- 19 6月, 2013 4 次提交
-
-
由 Kevin Hilman 提交于
Ensure the console uart (UART3) on these boards is mux'd correctly, and IO ring wakeup is enabled. This is needed for serial console wakeups when using DT boot. Thanks to Florian Vaussard for suggestion to use preprocessor features. Cc: Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by: NKevin Hilman <khilman@linaro.org> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Florian Vaussard 提交于
Using constants for pinctrl allows a better readability, and removes redundancy with comments. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Florian Vaussard 提交于
Use standard GPIO constants to enhance the readability of DT GPIOs. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Florian Vaussard 提交于
Replace /include/ by #include for OMAP2+ DT, in order to use the C pre-processor, making use of #define features possible. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
- 09 4月, 2013 2 次提交
-
-
由 Nishanth Menon 提交于
Define VDD1 regulator in twl4030 DT and mark it as the supply for the various OMAP34xx/35xx/36xx/37xx platforms (all use TWL4030 variants with VDD1 supplying the CPU). NOTE: This currently will use I2C1 bus communication path to set the voltage in device tree boot. In the legacy non device tree boot, we continue to use twl-common.c which bypasses I2C1 bus communication path and uses I2C4 bus path using OMAP voltage libraries. We should eventually be able to use I2C4 path once we have voltage regulator for OMAP which is capable of using the voltage controller/voltage processor IP blocks. Signed-off-by: NNishanth Menon <nm@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Jon Hunter <jon-hunter@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
由 Nishanth Menon 提交于
Add DT OPP table for OMAP34xx/35xx family of devices. This data is decoded by OF with of_init_opp_table() helper function. OPP data here is based on existing opp3xxx_data.c Since the omap36xx OPP tables would be different from OMAP34xx/35xx, introduce an new omap34xx.dtsi for 34xx/35xx specific entries and use existing omap3.dtsi as the common dtsi file for all OMAP3 platforms. This is in preparation to use generic cpufreq-cpu0 driver for device tree enabled boot. Legacy non device tree enabled boot continues to use omap-cpufreq.c and opp3xxx_data.c. Signed-off-by: NNishanth Menon <nm@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Jon Hunter <jon-hunter@ti.com> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Shawn Guo <shawn.guo@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>
-
- 03 4月, 2013 1 次提交
-
-
由 Roger Quadros 提交于
Provide RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for USB host pins. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by: NRoger Quadros <rogerq@ti.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 29 10月, 2012 1 次提交
-
-
由 Jon Hunter 提交于
Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This version of the Beagle board has 256MB of DDR and features the same TWL4030 power management IC (PMIC) as the Beagle board XM. Given that the Beagle and Beagle-XM boards use the same PMIC, move the definition of the VSIM regulator into the TWL4030.dtsi file so that we do not need to duplicate in the Beagle board dts file. This has been boot tested on an OMAP3530 Beagle board and verifing that the SD/MMC interface is working with a SD card. V2 changes - Rebased upon of devel-dt - Corrected copyright date in omap3-beagle.dts file - Added LED support after verifing that Beagle and Beagle XM have the same LED configuration Signed-off-by: NJon Hunter <jon-hunter@ti.com> Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
-
- 08 9月, 2012 1 次提交
-
-
由 Florian Vaussard 提交于
Add device tree properties for twl4030/gpio, according to the platform data of corresponding boards. This enables the led connected to LEDB output for both boards, as well as pullups/pulldowns on GPIO for the BeagleBoard. Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
-
- 02 7月, 2012 1 次提交
-
-
由 Vaibhav Hiremath 提交于
Add support for TWL4030, which is interfaced on i2c1 bus. Also add clock frequencies for other i2c instances (2 & 3) required for client-device exist on OMAP3EVM board. Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: NBenoit Cousson <b-cousson@ti.com> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 25 2月, 2012 1 次提交
-
-
由 Vaibhav Hiremath 提交于
Add OMAP3 EVM (OMAP3530, AM/DM37x) DTS file to use the omap3.dtsi SoC file, along with memory node information. Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: NBenoit Cousson <b-cousson@ti.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca>
-