The DSI PLL and HSDivider can be used to generate the pixel clock for
LCD overlay manager, which then goes to DPI output. On the DPI output
pin the voltage of the signal is shifted from the OMAP's internal
minimal voltage to 1.8V range. The shifting is not instant, and the
higher the clock frequency, the less time there is to shift the signal
to nominal voltage.

If the HSDivider's divider is greater than one and odd, the resulting
pixel clock does not have 50% duty cycle. For example, with a divider of
3, the duty cycle is 33%.

When combining high frequency (in the area of 140MHz+) and non-50% duty
cycle, it has been observed the the shifter does not have enough time to
shift the voltage enough, and this leads to bad signal which is rejected
by monitors.

As a workaround this patch makes the divider calculation skip all odd
dividers when the required pixel clock is over 100MHz. The limit of
100MHz is a guesstimate.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DPI may use DSI PLL, so it depends on DSI. However, currently DPI driver
is added first, which causes DPI initialization to fail when it tries to
get the DSI PLL.

This patch changes the init order to fix this.

A better solution would be to separate DSI PLL and DSI drivers. They
have dependencies, though, but we could still have DSI PLL as an
independent entity that we could initialize before any of the output
drivers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Merge omapdss miscellaneous patches.

Split the omap4_hdmi_mux_pads() function into two parts, one handles the
tpd12s015 gpio muxing, the other handles the hdmi pins.

This is clearer, as hdmi and tpd12s015 are separate devices, and it also
allows us to mux those separately with DT.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

The dispc error handler tries to "fix" issues by disabling and enabling
panel. This is problematic, as we're trying to remove the dependency
from omapdss to the omap_dss_devices. It's also racy, and doesn't really
fix anything.

This patch removes the use of omap_dss_device from the error handler,
and just disables and enables the associated overlay manager. This
should produce similar results as the previous solution, without using
dssdev.

However, the error handling is still horrible. But the problem boils
down to one question, to which I don't have a clear answer: what to do
when a HW error happens?
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The dispc's error handler has a loop inside another loop, and both use
the same loop variable. This is clearly wrong, and this patch makes a
new variable for the inner loop.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss_generic_clk_source_names is missing the names for clocks from DSI2
PLL. Add them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current omapfb code goes over all the modes found from the monitors
EDID data, and searches for a mode that is compatible with the DSS
hardware and has the highest x-res.

While this works ok as such, it proves problematic when using DSI PLL
for pixel clock. Calculating DSI PLL dividers is not the fastest of the
operations, and while doing it for one mode is usually ok, doing it for
20 modes is noticable.

Also, the first mode given in the EDID data should be the native mode of
the monitor, and thus also the best mode, so if that can be used, no
need to look further.

This patch changes the code to use the first mode that is compatible
with the DSS hardware.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

It seems that using the second EDID block causes more problems than is
of any help. The first mode in the extended block will get
FB_MODE_IS_FIRST set, which will override the first mode from the first
EDID block, thus making the default videomode selection not to work
properly.

This patch removes the use of the extended edid block for now.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The hdmi driver tries to find the given video timings from its static
list of timings, to find the required ID for the mode. The check tries
to find exact match for the pixel clock, among other checks.

with omapfb driver there can be some amount of error in the give pixel
clock, as the pixel clock is converted between Hz and ps, thus the
hdmi's check fails to find the mode.

This patch makes the check more allowing, by rounding the pixel clocks
to nearest MHz.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>

Add 1920x1200 video mode to hdmi driver's static modelist.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>

This patch makes use of the hdmi_power_[on|off]_core() functions added
in the previous patch. The functions are used when reading EDID or
detecting if a monitor is connected.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>

There's currently just one power-on function for HDMI, which enables the
IP and the video output. When reading EDID or detecting if a monitor is
connected, we don't need the video output.

Enabling the video output for these operations is not a big problem in
itself, but the quick enable/disable cycles caused by the operations
seem to cause sync lost errors from time to time. Also, this makes it
possible to read the EDID before the full video path has been set up.

This patch splits the hdmi_power_on into two parts, hdmi_power_on_core
and hdmi_power_on_full. The "full" version does what hdmi_power_on does
currently, and hdmi_power_on_core only enables the core IP. Similar
changes are made for power_off.

Note that these don't allow the HDMI IP to be first enabled, and later
enable the video output, but the HDMI IP will first need to be powered
off before calling the full version. So this is rather limited
implementation, but it fills the needs for reading EDID.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>

DISPC irqs need to be handled from the compat layer and also in the
future by the omapdrm. To make this possible, this patchs adds a set of
helper functions, so that the irqs can be managed without direct
register reads/writes.

The following functions are added, and all the current direct reg
reads/writes are changed to use these.

u32 dispc_read_irqstatus(void);
void dispc_clear_irqstatus(u32 mask);
u32 dispc_read_irqenable(void);
void dispc_write_irqenable(u32 mask);
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add new dispc function, dispc_ovl_enabled(). This returns if the overlay
enable bit is set in the registers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We need a low level manager-enable function for omapdrm. We have that
function as dispc internal func, _enable_mgr_out().

This patch exposes that function, and renames it to dispc_mgr_enable().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The current dispc_mgr_enable/disable function are blocking, and do a bit
too much for omapdrm. We'll expose new enable & disable functions that
will just set the bits in the registers in the following patches.

This patch renames the current functions to *_sync, to make it clear
that they are blocking, and also to free up the dispc_mgr_enable/disable
names for these new functions.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use dss_feat_get_num_ovls() in dispc.c instead of
omap_dss_get_num_overlays() to remove the dependency to overlay.c. Note
that we still have uses of omap_dss_get_num_overlays() in dispc.c, but
these will be moved out in the future patches.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently omapdss driver sets up the initial connections between
overlays, overlay manager and a panel, based on default display
parameter coming from the board file or via module parameters.

This is unnecessary, as it's the higher level component that should
decide what display to use and how. This patch removes the code from
omapdss, and implements similar code to omapfb.

The def_disp module parameter and the default display platform_data
parameter are kept in omapdss, but omapdss doesn't do anything with
them. It will just return the default display name with
dss_get_default_display_name() call, which omapfb uses. This is done to
keep the backward compatibility.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Export dss_get_def_display_name() with the name of
omapdss_get_def_display_name() so that omapfb can use it after the next
patch which moves default display handling to omapfb.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dispc_mgr_lclk_rate() cannot currently be called with DIGIT channel
parameter, even if dispc_ovl_lclk_rate() can. Fix this by making
dispc_mgr_lclk_rate() handle DIGIT channel also.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss.h contains dispc_irq_handler declaration, even if the function is
dispc.c internal. Remove the declaration.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The output drivers get the omapdss hw version from the platform data for
their respective output device. This doesn't work with DT, as there's no
platform data for them.

Add a new function, omapdss_get_version(), which returns the dss version
from the core device, which will have platform data on DT also. The
function is exported so that users of omapdss can also use it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The panel drivers contain enable, disable, suspend and resume calls.
The suspend and resume are effectively identical to disable and enable.

This patch removes panel suspend and enable code from omapdss and the
panel drivers, and replaces their use with enable and disable.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add the missing unlock on the error handling path in function
hdmi_dump_regs().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

acbi and acb fields were meant for passive matrix panels which omapdss
doesn't support any longer. Remove these fields from omap_dss_device
struct.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We currently have a single function to enable and disable the manager
output for LCD and DIGIT. The functions are a bit complex, as handling
both enable and disable require some extra steps to ensure that the
output is enabled or disabled properly without errors before exiting the
function.

The code can be made simpler to understand by splitting the functions
into separate enable and disable functions. We'll also clean up the
comments and some parameter names at the same time.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add function that returns the sync lost irq mask for the given channel.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dispc.c's functions to enable LCD and DIGIT outputs can be cleaned up a
bit by using common functions to set the enable bit and to check if the
output is enabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dispc_ovl_setup() uses struct omap_overlay to get the caps for the
overlay. We can change the code to get the caps directly from dss
features, thus removing the dependency to struct omap_overlay.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dss_mgr_set_device and dss_mgr_unset_device are declared in dss.h, but
the functions do not exist. Remove the declarations.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Dispc has a bunch of functions used to configure output related
parameters:

- dispc_mgr_set_io_pad_mode
- dispc_mgr_enable_stallmode
- dispc_mgr_enable_fifohandcheck
- dispc_mgr_set_clock_div
- dispc_mgr_set_tft_data_lines
- dispc_lcd_enable_signal_polarity
- dispc_mgr_set_lcd_type_tft

These are all called together, and the configuration values are taken
from struct dss_lcd_mgr_config.

Instead of exposing those individual dispc functions, create a new one,
dispc_mgr_set_lcd_config(), which is used to configure the above
parameters from values in struct dss_lcd_mgr_config.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add consts to dispc function parameters which do not modify the passed
structs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When we enable an output we don't check if we need to register the vsync
isr. This causes us to miss vsync interrupts until somebody changes the
configuration of an overlay or an overlay manager.

Add the registration to dss_mgr_enable to fix the problem.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

If dsi_get_dsidev_from_id() is called with a DSI module id that does not
exist on the board, the function will crash as omap_dss_get_output()
will return NULL.

This happens on omap3 boards when dumping DSI clocks, as the dumping
code will try to get the dsidev for DSI modules 0 and 1, but omap3 only
has DSI module 0.

Also clean up the id -> output mapping, so that if the function is
called with invalid module ID it will return NULL.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Archit Taneja <archit@ti.com>

Merge omap vrfb code to remove direct omap platform dependencies from the
driver.

Merge omapdss code to remove cpu_is_* checks from the driver.

Replace cpu_is_*() check with omap_vrfb_supported().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add an exported function omap_vrfb_supported() which returns true if the
vrfb driver has been loaded succesfully. This can be used to decide if
VRFB can be used or not.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that VRFB driver handles its registers independently, we can remove
the VRFB related code from OMAP's sdrc.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>