The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: FCC -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.

The CTL mappings for this regdomain code were now changed to:

* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this regdomain code are:

* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this regdomain code are:

* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this regdomain code are:

* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this regdomain code are:

* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this regdomain code are:

* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:

  Invalid EEPROM contents

The current CTL mappings for this country are:

* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: NSven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.

Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.

Supported Chipsets:
 -QCA988X/QCA9887 PCI
 -QCA99X0/QCA9984/QCA9888/QCA4019 PCI
 -QCA6174/QCA9377 PCI/USB/SDIO
 -WCN3990 SNOC

Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds firmware crash memory dump support for QCA9888 and QCA99X0.

Tested on:

QCA9888 firmware 10.4-3.5.3-00053
QCA99X0 firmware 10.4.1.00030-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Auto rate table sent to firmware is getting corrupted
as memset to zeros is not done. Added memset to skb
data before filling auto rate table.
Signed-off-by: NSanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: NSushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: NSanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: NSushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This allows reading all capabilities as reported by a firmware. They are
printed using native (raw) names, just like developers like it the most.
It's how firmware reports support for various features, e.g. supported
modes, supported standards, power saving details, max BSS-es.

Access to all that info is useful for trying new firmwares, comparing
them and debugging features AKA bugs.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Correct snr/nr/rssi data index to avoid possible buffer underflow.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

usleep_range can cause excessive latency on channel change if waiting
for the MAC to stop fails. It will be forced to stop by the code
following that loop anyway.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Reduces interruption caused by scanning
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>