Create a specific helper for netlink kernel socket disposal. This just
let the code look better and provides a ground for proper disposal
inside a namespace.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Tested-by: NAlexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network namespace allocates 2 kernel netlink sockets, fibnl &
rtnl. These sockets should be disposed properly, i.e. by
sock_release. Plain sock_put is not enough.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Tested-by: NAlexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netlink protocol table is global for all namespaces. Some netlink
protocols have been virtualized, i.e. they have per/namespace netlink
socket. This difference can easily lead to double free if more than 1
namespace is started. Count the number of kernel netlink sockets to
track that this table is not used any more.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Tested-by: NAlexey Dobriyan <adobriyan@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexey Dobriyan reported an oops when unsharing the network
indefinitely inside a loop. This is because the ip6_frag is not per
namespace while the ctls are.

That happens at the fragment timer expiration:
inet_frag_secret_rebuild function is called and this one restarts the
timer using the value stored inside the sysctl field.

        "mod_timer(&f->secret_timer, now + f->ctl->secret_interval);"

When the network is unshared, ip6_frag.ctl is initialized with the new
sysctl instances, but ip6_frag has only one instance. A race in this
case will appear because f->ctl can be modified during the read access
in the timer callback.

Until the ip6_frag is not per namespace, I discard the assignation to
the ctl field of ip6_frags in ip6_frag_sysctl_init when the network
namespace is not the init net.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, all non TAH equipped 4xx PPC's call emac_start_xmit() upon
xmit. This routine doesn't check if the frame length exceeds the max.
MAL buffer size.

This patch now changes the driver to call emac_start_xmit_sg() on all
GigE platforms and not only the TAH equipped ones (440GX). This enables
an MTU of 9000 instead 4080.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NClaudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When doing init_ring checking whether a new skb needs to be allocated
was wrong.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update driver version reflects new hardware support.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add support from sk98lin vendor driver 10.50.1.3 for 88E8055 and
88E8075 chips.  I don't have this hardware to test, so this changes
are untested.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

stop the byteswap-in-place, annotate
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Use inline functions for dma_sync_* instead of macros
- added Kconfig change to make selection for similair SGI boxes easier
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds me as maintainer of the RDC R6040 Fast Ethernet driver.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
--
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch skips mac80211 configuration setting during a hardware scan
and replays it afterwards for the iwlwifi drivers.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch changes the iwlwifi driver to properly support
monitor interfaces after the filter flags change.

The patch is originally created by Johannes Berg for iwl4965. I fixed some
of the comments and created a similar patch for iwl3945.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sizeof(*cmd) is going to give the total size of the data structure that
we allocated, more often than not. But the size of the command to be
_sent_ could be a lot smaller, as it is in the KEY_MATERIAL and
SUBSCRIBE_EVENT commands for example. So swap them round; let the caller
set the _command_ size explicitly in the header, and infer the
maximum response size from the data structure.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We don't necessarily want to reset the device on a TX timeout. But more
often than not, the real cause is that the firmware has crapped itself,
not just that the network is busy. So submit any harmless command, and
if _that_ times out, then the error handling code will reset the module,
as appropriate.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Even if it fails, we want to wait a while and try again, with an
ultimate timeout if it the condition persists. So again, just use the
standard command timeout behaviour.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the firmware returns 0x0004, it wants us to try again later. We can
achieve that simply by throwing out the response and letting the command
timeout code kick in.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we don't scribble over the command we sent, then we can retry it when
the firmware responds with 0x0004 (which means -EAGAIN).
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have a local variable 'resp' which we use for this. So use it,
instead of typing the whole thing.

In preparation for actually using priv->upld_buf for the responses
instead...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the various firmware setup bits into a separate function, which
used to do just boot2 version.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, we go into an endless busy loop trying to enable PS mode when
the command queue is empty, dealing with the error response, and then
trying to enable PS mode again because the command queue is empty.... it
doesn't really save much power.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

lbs_send_confirmwake() is a bit ugly but matches the way we confirm
sleep. We'll deal with that whole thing later.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DNLD_RES_RECEIVED is a bit of a misnomer -- we never wait for the result
to be received; it's purely representing the state of the TX path, and
in this case the TX path is definitely busy.

Of course, that means that we don't actually care about DATA_SENT vs.
CMD_SENT either, but that's a can of worms for another day...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 5b8845345e7385d2eb37fac22ba9ab6905988be5 (or, in case the git
workflow is broken and patches get recommitted, the commit entitled
'libertas: rename and re-type bufvirtualaddr to cmdbuf' by dcbw),
introduced a number of bugs where we once had a pointer to a command
_payload_, but now we use the pointer to the command header instead.

The fix isn't wonderfully pretty for now, but it'll get better when we
finish converting all commands so the structures include the header.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we return the channel number in a 'ret' variable where anything
non-zero is later interpreted as an error, that isn't nice. It breaks
WPA, for a start. OLPC trac #5485
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>