The adrp instruction is mostly used in combination with either
an add, a ldr or a str instruction with the low bits of the
referenced symbol in the 12-bit immediate of the followup
instruction.

Introduce the macros adr_l, ldr_l and str_l that encapsulate
these common patterns.
Tested-by: NMark Rutland <mark.rutland@arm.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

struct cpu_table is an artifact left from the (very) early days of
the arm64 port, and its only real use is to allow the most beautiful
"AArch64 Processor" string to be displayed at boot time.

Really? Yes, really.

Let's get rid of it. In order to avoid another BogoMips-gate, the
aforementioned string is preserved.
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Raise the maximum CPU limit to 4096 in preparation for upcoming
platforms with large core counts.
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGanapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The perf core implicitly rejects events spanning multiple HW PMUs, as in
these cases the event->ctx will differ. However this validation is
performed after pmu::event_init() is called in perf_init_event(), and
thus pmu::event_init() may be called with a group leader from a
different HW PMU.

The ARM64 PMU driver does not take this fact into account, and when
validating groups assumes that it can call to_arm_pmu(event->pmu) for
any HW event. When the event in question is from another HW PMU this is
wrong, and results in dereferencing garbage.

This patch updates the ARM64 PMU driver to first test for and reject
events from other PMUs, moving the to_arm_pmu and related logic after
this test. Fixes a crash triggered by perf_fuzzer on Linux-4.0-rc2, with
a CCI PMU present:

Bad mode in Synchronous Abort handler detected, code 0x86000006 -- IABT (current EL)
CPU: 0 PID: 1371 Comm: perf_fuzzer Not tainted 3.19.0+ #249
Hardware name: V2F-1XV7 Cortex-A53x2 SMM (DT)
task: ffffffc07c73a280 ti: ffffffc07b0a0000 task.ti: ffffffc07b0a0000
PC is at 0x0
LR is at validate_event+0x90/0xa8
pc : [<0000000000000000>] lr : [<ffffffc000090228>] pstate: 00000145
sp : ffffffc07b0a3ba0

[<          (null)>]           (null)
[<ffffffc0000907d8>] armpmu_event_init+0x174/0x3cc
[<ffffffc00015d870>] perf_try_init_event+0x34/0x70
[<ffffffc000164094>] perf_init_event+0xe0/0x10c
[<ffffffc000164348>] perf_event_alloc+0x288/0x358
[<ffffffc000164c5c>] SyS_perf_event_open+0x464/0x98c
Code: bad PC value

Also cleans up the code to use the arm_pmu only when we know
that we are dealing with an arm pmu event.

Cc: Will Deacon <will.deacon@arm.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NPeter Ziljstra (Intel) <peterz@infradead.org>
Signed-off-by: NSuzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This changes the AES core transform implementations to issue aese/aesmc
(and aesd/aesimc) in pairs. This enables a micro-architectural optimization
in recent Cortex-A5x cores that improves performance by 50-90%.

Measured performance in cycles per byte (Cortex-A57):

                CBC enc         CBC dec         CTR
  before        3.64            1.34            1.32
  after         1.95            0.85            0.93

Note that this results in a ~5% performance decrease for older cores.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Fixmap indices are in the interval (FIX_HOLE, __end_of_fixed_addresses),
but in __set_fixmap we only check idx <= __end_of_fixed_addresses, and
therefore indices <= FIX_HOLE are erroneously accepted. If called with
such an idx, __set_fixmap may corrupt page tables outside of the fixmap
region.

This patch ensures that we validate the idx against both endpoints of
the interval.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The FIX_TEXT_POKE0 is currently at the end of the temporary fixmap
slots, despite the fact that it can be used at any point during runtime
(e.g. for poking the text of loaded modules), and thus should be a
permanent fixmap slot (as is the case on arm and x86).

This patch moves FIX_TEXT_POKE0 into the set of permanent fixmap slots.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

This effectively unexports set_memory_ro and set_memory_rw functions from
commit 11d91a77 ("arm64: Add CONFIG_DEBUG_SET_MODULE_RONX support").

No module user of those is in mainline kernel and we explicitly do not want
modules to use these functions, as they i.e. RO-protect eBPF (interpreted and
JIT'ed) images from malicious modifications/bugs.

Outside of eBPF scope, I believe also other set_memory_* functions should
be unexported on arm64 due to non-existant mainline module user. Laura
mentioned that they have some uses for modules doing set_memory_*, but
none that are in mainline and it's unclear if they would ever get there.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

With binutils 2.25 the default alignment for 32bit arm sections changed to
have everything 64k aligned. Armv7 binaries built with this binutils version
run successfully on an arm64 system.

Since effectively there is now the chance to run armv7 code on arm64 even
with 64k page size, it doesn't make sense to block people from enabling
CONFIG_COMPAT on those configurations.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

The arm mmap2 syscall takes the offset in units of 4K, thus with 64K pages
the offset needs to be scaled to units of pages.
Signed-off-by: NAndreas Schwab <schwab@suse.de>
Signed-off-by: NAlexander Graf <agraf@suse.de>
[will: removed redundant lr parameter, localised PAGE_SHIFT #if check]
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Commit f4f75ad5 ("efi: efistub: Convert into static library")
introduced a static library for EFI stub, libstub.

The EFI libstub directory is referenced by the kernel build system via
a obj subdirectory rule in:
drivers/firmware/efi/Makefile

Unfortunately, arm64 also references the EFI libstub via:
libs-$(CONFIG_EFI_STUB) += drivers/firmware/efi/libstub/

If we're unlucky, the kernel build system can enter libstub via two
simultaneous threads resulting in build failures such as:

fixdep: error opening depfile: drivers/firmware/efi/libstub/.efi-stub-helper.o.d: No such file or directory
scripts/Makefile.build:257: recipe for target 'drivers/firmware/efi/libstub/efi-stub-helper.o' failed
make[1]: *** [drivers/firmware/efi/libstub/efi-stub-helper.o] Error 2
Makefile:939: recipe for target 'drivers/firmware/efi/libstub' failed
make: *** [drivers/firmware/efi/libstub] Error 2
make: *** Waiting for unfinished jobs....

This patch adjusts the arm64 Makefile to reference the compiled library
explicitly (as is currently done in x86), rather than the directory.

Fixes: f4f75ad5 efi: efistub: Convert into static library
Signed-off-by: NSteve Capper <steve.capper@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

We currently don't log the boot mode for arm64 as we do for arm, and
without KVM the user is provided with no indication as to which mode(s)
CPUs were booted in, which can seriously hinder debugging in some cases.

Add logging to the boot path once all CPUs are up. Where CPUs are
mismatched in violation of the boot protocol, WARN and set a taint (as
we do for CPU other CPU feature mismatches) given that the
firmware/bootloader is buggy and should be fixed.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Commit 828e9834 ("arm64: head: create a new function for setting
the boot_cpu_mode flag") added BOOT_CPU_MODE_EL1, a nonzero value
replacing uses of zero. However it failed to update __boot_cpu_mode
appropriately.

A CPU booted at EL2 writes BOOT_CPU_MODE_EL2 to __boot_cpu_mode[0], and
a CPU booted at EL1 writes BOOT_CPU_MODE_EL1 to __boot_cpu_mode[1].
Later is_hyp_mode_mismatched() determines there to be a mismatch if
__boot_cpu_mode[0] != __boot_cpu_mode[1].

If all CPUs are booted at EL1, __boot_cpu_mode[0] will be set to
BOOT_CPU_MODE_EL1, but __boot_cpu_mode[1] will retain its initial value
of zero, and is_hyp_mode_mismatched will erroneously determine that the
boot modes are mismatched. This hasn't been a problem so far, but later
patches which will make use of is_hyp_mode_mismatched() expect it to
work correctly.

This patch initialises __boot_cpu_mode[1] to BOOT_CPU_MODE_EL1, fixing
the erroneous mismatch detection when all CPUs are booted at EL1.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Currently we only perform alternative patching for kernels built with
CONFIG_SMP, as we call apply_alternatives_all() in smp.c, which is only
built for CONFIG_SMP. Thus !SMP kernels may not have necessary
alternatives patched in.

This patch ensures that we call apply_alternatives_all() once all CPUs
are booted, even for !SMP kernels, by having the smp_init_cpus() stub
call this for !SMP kernels via up_late_init. A new wrapper,
do_post_cpus_up_work, is added so we can hook other calls here later
(e.g. boot mode logging).

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: e039ee4e ("arm64: add alternative runtime patching")
Tested-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

ARM64 has the yield nop hint which has the intended semantics of
cpu_relax. Implement.

The immediate application is ARM CPU emulators. An emulator can take
advantage of the yield hint to de-prioritise an emulated CPU in favor
of other emulation tasks. QEMU A64 SMP emulation has yield awareness,
and sees a significant boot time performance increase with this change.
Signed-off-by: NPeter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Another one for the big head.S spring cleaning: the label should
be after the .align or it may point to the padding.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

If UEFI Runtime Services are available, they are preferred over direct
PSCI calls or other methods to reset the system.

For the reset case, we need to hook into machine_restart(), as the
arm_pm_restart function pointer may be overwritten by modules.
Tested-by: NMark Rutland <mark.rutland@arm.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Reviewed-by: NMatt Fleming <matt.fleming@intel.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The ARM architecture allows the caching of intermediate page table
levels and page table freeing requires a sequence like:

	pmd_clear()
	TLB invalidation
	pte page freeing

With commit 5e5f6dc1 (arm64: mm: enable HAVE_RCU_TABLE_FREE logic),
the page table freeing batching was moved from tlb_remove_page() to
tlb_remove_table(). The former takes care of TLB invalidation as this is
also shared with pte clearing and page cache page freeing. The latter,
however, does not invalidate the TLBs for intermediate page table levels
as it probably relies on the architecture code to do it if required.
When the mm->mm_users < 2, tlb_remove_table() does not do any batching
and page table pages are freed before tlb_finish_mmu() which performs
the actual TLB invalidation.

This patch introduces __tlb_flush_pgtable() for arm64 and calls it from
the {pte,pmd,pud}_free_tlb() directly without relying on deferred page
table freeing.

Fixes: 5e5f6dc1 arm64: mm: enable HAVE_RCU_TABLE_FREE logic
Reported-by: NJon Masters <jcm@redhat.com>
Tested-by: NJon Masters <jcm@redhat.com>
Tested-by: NSteve Capper <steve.capper@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The set_memory_* functions currently only support module
addresses. The addresses are validated using is_module_addr.
That function is special though and relies on internal state
in the module subsystem to work properly. At the time of
module initialization and calling set_memory_*, it's too early
for is_module_addr to work properly so it always returns
false. Rather than be subject to the whims of the module state,
just bounds check against the module virtual address range.
Signed-off-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.

The new bindings are in sync with the newer firmware.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKeyur Chudgar <kchudgar@apm.com>
Tested-by: NMark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ARM64 CPUidle driver requires the cpu_do_idle function so that it can
be used to enter the shallowest idle state, and it is declared in
asm/proc-fns.h.

The current ARM64 CPUidle driver does not include asm/proc-fns.h
explicitly and it has so far relied on implicit inclusion from other
header files.

Owing to some header dependencies reshuffling this currently triggers
build failures when CONFIG_ARM64_64K_PAGES=y:

drivers/cpuidle/cpuidle-arm64.c: In function "arm64_enter_idle_state"
drivers/cpuidle/cpuidle-arm64.c:42:3: error: implicit declaration of
function "cpu_do_idle" [-Werror=implicit-function-declaration]
   cpu_do_idle();
   ^

This patch adds the explicit inclusion of the asm/proc-fns.h header file
in the arm64 asm/cpuidle.h header file, so that the build breakage is fixed
and the required header inclusion is added to the appropriate arch back-end
CPUidle header, already included by the CPUidle arm64 driver, where
CPUidle arch related function declarations belong.
Reported-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Tested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.

Cc: <stable@vger.kernel.org>
Reported-by: NBamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Tested-by: NBamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

With commit 3690951f (arm64: Use swiotlb late initialisation), the
swiotlb buffer size is limited to MAX_ORDER_NR_PAGES. However, there are
platforms with 32-bit only devices that require bounce buffering via
swiotlb. This patch changes the swiotlb initialisation to an early 64MB
memblock allocation. In order to get the swiotlb buffer correctly
allocated (via memblock_virt_alloc_low_nopanic), this patch also defines
ARCH_LOW_ADDRESS_LIMIT to the maximum physical address capable of 32-bit
DMA.
Reported-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Patch 2f896d58 ("arm64: use fixmap for text patching") changed
the way we patch the kernel text, using a fixmap when the kernel or
modules are flagged as read only.

Unfortunately, a flaw in the logic makes it fall over when patching
modules without CONFIG_DEBUG_SET_MODULE_RONX enabled:

[...]
[   32.032636] Call trace:
[   32.032716] [<fffffe00003da0dc>] __copy_to_user+0x2c/0x60
[   32.032837] [<fffffe0000099f08>] __aarch64_insn_write+0x94/0xf8
[   32.033027] [<fffffe000009a0a0>] aarch64_insn_patch_text_nosync+0x18/0x58
[   32.033200] [<fffffe000009c3ec>] ftrace_modify_code+0x58/0x84
[   32.033363] [<fffffe000009c4e4>] ftrace_make_nop+0x3c/0x58
[   32.033532] [<fffffe0000164420>] ftrace_process_locs+0x3d0/0x5c8
[   32.033709] [<fffffe00001661cc>] ftrace_module_init+0x28/0x34
[   32.033882] [<fffffe0000135148>] load_module+0xbb8/0xfc4
[   32.034044] [<fffffe0000135714>] SyS_finit_module+0x94/0xc4
[...]

This is triggered by the use of virt_to_page() on a module address,
which ends to pointing to Nowhereland if you're lucky, or corrupt
your precious data if not.

This patch fixes the logic by mimicking what is done on arm:
- If we're patching a module and CONFIG_DEBUG_SET_MODULE_RONX is set,
  use vmalloc_to_page().
- If we're patching the kernel and CONFIG_DEBUG_RODATA is set,
  use virt_to_page().
- Otherwise, use the provided address, as we can write to it directly.

Tested on 4.0-rc1 as a KVM guest.
Reported-by: NRichard W.M. Jones <rjones@redhat.com>
Reviewed-by: NKees Cook <keescook@chromium.org>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NLaura Abbott <lauraa@codeaurora.org>
Tested-by: NRichard W.M. Jones <rjones@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch increases the interleave factor for parallel AES modes
to 4x. This improves performance on Cortex-A57 by ~35%. This is
due to the 3-cycle latency of AES instructions on the A57's
relatively deep pipeline (compared to Cortex-A53 where the AES
instruction latency is only 2 cycles).

At the same time, disable inline expansion of the core AES functions,
as the performance benefit of this feature is negligible.

  Measured on AMD Seattle (using tcrypt.ko mode=500 sec=1):

  Baseline (2x interleave, inline expansion)
  ------------------------------------------
  testing speed of async cbc(aes) (cbc-aes-ce) decryption
  test 4 (128 bit key, 8192 byte blocks): 95545 operations in 1 seconds
  test 14 (256 bit key, 8192 byte blocks): 68496 operations in 1 seconds

  This patch (4x interleave, no inline expansion)
  -----------------------------------------------
  testing speed of async cbc(aes) (cbc-aes-ce) decryption
  test 4 (128 bit key, 8192 byte blocks): 124735 operations in 1 seconds
  test 14 (256 bit key, 8192 byte blocks): 92328 operations in 1 seconds
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Caught during Trinity testing. The pte_modify does not allow
modification for PTE type bit. This cause the test to hang
the system. It is found that the PTE can't transit from an
inaccessible page (b00) to a valid page (b11) because the mask
does not allow it. This happens when a big block of mmaped
memory is set the PROT_NONE, then the a small piece is broken
off and set to PROT_WRITE | PROT_READ cause a huge page split.
Signed-off-by: NFeng Kan <fkan@apm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The functions __cpu_flush_user_tlb_range and __cpu_flush_kern_tlb_range
were removed in commit fa48e6f7 'arm64: mm: Optimise tlb flush logic
where we have >4K granule'. Global variable cpu_tlb was never used in
arm64.

Remove them.
Signed-off-by: NYingjoe Chen <yingjoe.chen@mediatek.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

An arm64 allmodconfig fails to build with GCC 5 due to __asmeq
assertions in the PSCI firmware calling code firing due to mcount
preambles breaking our assumptions about register allocation of function
arguments:

  /tmp/ccDqJsJ6.s: Assembler messages:
  /tmp/ccDqJsJ6.s:60: Error: .err encountered
  /tmp/ccDqJsJ6.s:61: Error: .err encountered
  /tmp/ccDqJsJ6.s:62: Error: .err encountered
  /tmp/ccDqJsJ6.s:99: Error: .err encountered
  /tmp/ccDqJsJ6.s:100: Error: .err encountered
  /tmp/ccDqJsJ6.s:101: Error: .err encountered

This patch fixes the issue by moving the PSCI calls out-of-line into
their own assembly files, which are safe from the compiler's meddling
fingers.
Reported-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The vdso implementation of clock_getres currently returns 0 (success)
whenever a null timespec is provided by the caller, regardless of the
clock id supplied.

This behavior is incorrect.  It should fall back to syscall when an
unrecognized clock id is passed, even when the timespec argument is
null.  This ensures that clock_getres always returns an error for
invalid clock ids.
Signed-off-by: NNathan Lynch <nathan_lynch@mentor.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Commit 5d425c18 ("arm64: kernel: add support for cpu cache
information") adds cacheinfo support for ARM64. Since there's no
architectural way of detecting the cpus that share particular cache,
device tree can be used and the core cacheinfo already supports the
same.

This patch adds the L2 cache topology on Juno board, FVP/RTSM and
foundation models.
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

asm/assembler.h lacks the usual guard against multiple inclusion,
leading to a compilation failure if it is accidentally included
twice.

Using the classic #ifndef/#define/#endif construct solves the issue.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

Fix cbz/cbnz having the mask offset by a bit, and add encodings for
tbz/tbnz so that all branch forms are represented.
Signed-off-by: NRobin Murphy <robin.murphy@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NZi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

ftrace_enable_ftrace_graph_caller and ftrace_disable_ftrace_graph_caller
should replace B(jmp) instruction and not BL(call) instruction.

Commit 9f1ae759("arm64: Correct ftrace calls to
aarch64_insn_gen_branch_imm()") had a typo and used
AARCH64_INSN_BRANCH_LINK instead of AARCH64_INSN_BRANCH_NOLINK.

Either instruction will work, as the link register is saved/restored
across the branch but this better matches the intention of the code.
Signed-off-by: NPratyush Anand <panand@redhat.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

For instrumenting global variables KASan will shadow memory backing memory
for modules.  So on module loading we will need to allocate memory for
shadow and map it at address in shadow that corresponds to the address
allocated in module_alloc().

__vmalloc_node_range() could be used for this purpose, except it puts a
guard hole after allocated area.  Guard hole in shadow memory should be a
problem because at some future point we might need to have a shadow memory
at address occupied by guard hole.  So we could fail to allocate shadow
for module_alloc().

Now we have VM_NO_GUARD flag disabling guard page, so we need to pass into
__vmalloc_node_range().  Add new parameter 'vm_flags' to
__vmalloc_node_range() function.
Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: NAndrey Konovalov <adech.fo@gmail.com>
Cc: Yuri Gribov <tetra2005@gmail.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target.  This is because the
restart_block is held in the same memory allocation as the kernel stack.

Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.

Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.

It's also a decent simplification, since the restart code is more or less
identical on all architectures.

[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: NRichard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

LKP has triggered a compiler warning after my recent patch "mm: account
pmd page tables to the process":

    mm/mmap.c: In function 'exit_mmap':
 >> mm/mmap.c:2857:2: warning: right shift count >= width of type [enabled by default]

The code:

 > 2857                WARN_ON(mm_nr_pmds(mm) >
   2858                                round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT);

In this, on tile, we have FIRST_USER_ADDRESS defined as 0.  round_up() has
the same type -- int.  PUD_SHIFT.

I think the best way to fix it is to define FIRST_USER_ADDRESS as unsigned
long.  On every arch for consistency.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently we have many duplicates in definitions around
follow_huge_addr(), follow_huge_pmd(), and follow_huge_pud(), so this
patch tries to remove the m.  The basic idea is to put the default
implementation for these functions in mm/hugetlb.c as weak symbols
(regardless of CONFIG_ARCH_WANT_GENERAL_HUGETL B), and to implement
arch-specific code only when the arch needs it.

For follow_huge_addr(), only powerpc and ia64 have their own
implementation, and in all other architectures this function just returns
ERR_PTR(-EINVAL).  So this patch sets returning ERR_PTR(-EINVAL) as
default.

As for follow_huge_(pmd|pud)(), if (pmd|pud)_huge() is implemented to
always return 0 in your architecture (like in ia64 or sparc,) it's never
called (the callsite is optimized away) no matter how implemented it is.
So in such architectures, we don't need arch-specific implementation.

In some architecture (like mips, s390 and tile,) their current
arch-specific follow_huge_(pmd|pud)() are effectively identical with the
common code, so this patch lets these architecture use the common code.

One exception is metag, where pmd_huge() could return non-zero but it
expects follow_huge_pmd() to always return NULL.  This means that we need
arch-specific implementation which returns NULL.  This behavior looks
strange to me (because non-zero pmd_huge() implies that the architecture
supports PMD-based hugepage, so follow_huge_pmd() can/should return some
relevant value,) but that's beyond this cleanup patch, so let's keep it.

Justification of non-trivial changes:
- in s390, follow_huge_pmd() checks !MACHINE_HAS_HPAGE at first, and this
  patch removes the check. This is OK because we can assume MACHINE_HAS_HPAGE
  is true when follow_huge_pmd() can be called (note that pmd_huge() has
  the same check and always returns 0 for !MACHINE_HAS_HPAGE.)
- in s390 and mips, we use HPAGE_MASK instead of PMD_MASK as done in common
  code. This patch forces these archs use PMD_MASK, but it's OK because
  they are identical in both archs.
  In s390, both of HPAGE_SHIFT and PMD_SHIFT are 20.
  In mips, HPAGE_SHIFT is defined as (PAGE_SHIFT + PAGE_SHIFT - 3) and
  PMD_SHIFT is define as (PAGE_SHIFT + PAGE_SHIFT + PTE_ORDER - 3), but
  PTE_ORDER is always 0, so these are identical.
Signed-off-by: NNaoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We've replaced remap_file_pages(2) implementation with emulation.  Nobody
creates non-linear mapping anymore.

This patch also adjust __SWP_TYPE_SHIFT and increase number of bits
availble for swap offset.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch introduces a new module parameter for the KVM module; when it
is present, KVM attempts a bit of polling on every HLT before scheduling
itself out via kvm_vcpu_block.

This parameter helps a lot for latency-bound workloads---in particular
I tested it with O_DSYNC writes with a battery-backed disk in the host.
In this case, writes are fast (because the data doesn't have to go all
the way to the platters) but they cannot be merged by either the host or
the guest.  KVM's performance here is usually around 30% of bare metal,
or 50% if you use cache=directsync or cache=writethrough (these
parameters avoid that the guest sends pointless flush requests, and
at the same time they are not slow because of the battery-backed cache).
The bad performance happens because on every halt the host CPU decides
to halt itself too.  When the interrupt comes, the vCPU thread is then
migrated to a new physical CPU, and in general the latency is horrible
because the vCPU thread has to be scheduled back in.

With this patch performance reaches 60-65% of bare metal and, more
important, 99% of what you get if you use idle=poll in the guest.  This
means that the tunable gets rid of this particular bottleneck, and more
work can be done to improve performance in the kernel or QEMU.

Of course there is some price to pay; every time an otherwise idle vCPUs
is interrupted by an interrupt, it will poll unnecessarily and thus
impose a little load on the host.  The above results were obtained with
a mostly random value of the parameter (500000), and the load was around
1.5-2.5% CPU usage on one of the host's core for each idle guest vCPU.

The patch also adds a new stat, /sys/kernel/debug/kvm/halt_successful_poll,
that can be used to tune the parameter.  It counts how many HLT
instructions received an interrupt during the polling period; each
successful poll avoids that Linux schedules the VCPU thread out and back
in, and may also avoid a likely trip to C1 and back for the physical CPU.

While the VM is idle, a Linux 4 VCPU VM halts around 10 times per second.
Of these halts, almost all are failed polls.  During the benchmark,
instead, basically all halts end within the polling period, except a more
or less constant stream of 50 per second coming from vCPUs that are not
running the benchmark.  The wasted time is thus very low.  Things may
be slightly different for Windows VMs, which have a ~10 ms timer tick.

The effect is also visible on Marcelo's recently-introduced latency
test for the TSC deadline timer.  Though of course a non-RT kernel has
awful latency bounds, the latency of the timer is around 8000-10000 clock
cycles compared to 20000-120000 without setting halt_poll_ns.  For the TSC
deadline timer, thus, the effect is both a smaller average latency and
a smaller variance.
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The comment was right originally but the _pad array size was wrong. It
was fixed in the meantime but the comment not updated.
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>