This adds counters for tx and rx bytes, including any
errored packets as well as all wireless headers.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Initialize the rate table for WDS interfaces, and
add cases to allow WDS packets to pass the xmit and receive
tests.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added a nl interface to set the peer bssid of a WDS interface.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable WDS for the ath9k driver.
Signed-off-by: NBill Jordan <bjordan@rajant.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On association to an AP, after receiving beacons, the beacon_crc value is set.
The beacon_crc value is not reset in disassociation, but the BSS data may be
expired at a later point. When associating again, it's possible that a
beacon for the AP is not received, resulting in the beacon_ies to remain NULL.

After association, further beacons will not update the beacon data, as the
crc value of the beacon has not changed, and the beacon_crc still holds a
value matching the beacon. The beacon_ies will remain forever null.

One of the results of this is that WLAN power save cannot be entered, the STA
will remain foreven in active mode.

Fix this by adding a validation flag for the beacon_crc, which is cleared on
association.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move ieee80211_scan_cancel() and all other related code to
ieee80211_restart_work() as ieee80211_restart_hw() is intended to be
callable from any context.

Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan().

Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning)
to prevent the race condition with __ieee80211_start_scan() described
here: http://marc.info/?l=linux-wireless&m=128516716810537&w=2Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the ath9k debugging feature 'wiphy' the current channel used by the
station is incorrectly displayed.This is because the channels available
are sequentially mapped from numbers 0 to 37.This mapping cannot be
changed as the channel number is also used as an array index
          This fix solves the above problem by calculating the channel
number from center frequency.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The percal struct and bitmask for the initial DC calibration are not
used anywhere, so they can be removed.

Signed-off-by: Felix Fietkau <nbd@openwrt.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the regulatory code touches the channel array, it needs to be
copied for each device instance. That way the original channel array
can also be made const.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org [all]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add missing unlocking of the wiphy in set_channel,
and don't try to unlock a non-existing wiphy in
set_cqm.

Cc: stable@kernel.org [2.6.35+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support up to 4 virtual APs and as many virtual STA interfaces
as desired.

This patch is ported forward from a patch that Patrick McHardy
did for me against 2.6.31.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The net/cfg80211.h header file isn't exported to
userspace, so there's no need for any kind of
__KERNEL__ protection in it. If it was exported,
everything else in it would need protection as
well, not just the logging stuff ...

Cc:Joe Perches <joe@perches.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can start restarting firmware or RF kill switch can be turned on
during call to iwl_mac_add_interface(). That are normal working
conditions, so do not print call trace, just print simple message
instead.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The combined firmware ar9170.fw is preferred and supports all devices.
References to the older two-stage firmware are unnecessary.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some user space applications only want to display survey data for
the operating channel, however there is no API to get that yet.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

common->ani.noise_floor is now only used for a similar redundant debug
message similar to the one that was removed from ath9k_htc in an earlier
patch. Remove it from ath9k as well now.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is unused aside from a single redundant debug message
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware rx-filter was essentially disabled, because
of a serve, yet unidentifiable problem with iwlagn.
Due to these circumstances the driver and mac80211 were
left with the job of filtering.

This is very unfortunate and has proven to be expensive
in terms of latency, memory and load.

Therefore the new 1.8.8.3 firmware introduces a flexible
filtering infrastructure which allows the driver to
offload some of the checks (FCS & PLCP crc check,
RA match, control frame filter, etc...) whenever possible.

Note:
This patch also includes all changes to the
shared headers files since the inclusion.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an refcounting bug. Previously it
was possible to corrupt the per-device recv. filter
and monitor management counters when:
	iw dev wlanX set monitor [new flags]
was issued on an active monitor interface.
Acked-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Choose first available phyX name when creating phy devices.  This
means that reloading a wifi driver will not cause a change in the
name of it's phy device.

Also, allow users to rename a phy to any un-used name, including
phy%d.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

For 6050 series device, change the supported API version
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since uCode is responsible for doing DC calibration, there's no need
to let init uCode to do initial DC calibration then send results
back to driver, then driver sends the results to runtime uCode.
Driver can simply tell runtime uCode to do DC calibration.

Actually, this patch does not disable DC calib for init uCode. It just
prevent driver from saving and sending the DC calib results (from init
ucode) to runtime uCode. The driver still uses 0xffffffff in
CALIB_CFG_CMD for init ucode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For 6050g2 devices driver needs to set a special bit to CSR register
so that uCode can do things correctly in calibration routines.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi driver supports multiple devices. Since some device needs
special configuration we create a new iwl_nic_ops structure which is
configurable per device. Currently there is only one function pointer
inside this structure: additional_nic_config().

The iwl_nic_ops structure is added to the top level in struct iwl_ops,
making it easier to change per device. Duplication of the iwl_lib_ops
structure is no longer needed.

With this new ops the previous function pointer set_calib_version is
no longer needed since it is just a per device nic configuration.

As part of the code restructuring, a bug is addressed. Indication of
calib version to uCode is only needed for 6050 devices, however,
current implementation set calib version for all 6000 devices for
which DC calib is needed. To fix this, create iwl6050_ops for 6050
devices and only populate iwl_nic_ops in this structure.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

add new structures and defines need to identify 100 devices.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-agn-lib.c
	drivers/net/wireless/iwlwifi/iwl3945-base.c

The WMM parameter configuration function (ieee80211_sta_wmm_params) only
configures the WMM parameters to the driver is the wmm_last_param_set
counter value is changed by the AP.

The wmm_last_param_set is initialized to -1 on association in order to ensure
the configuration is made to the driver at least once on association, but
currently this initialization is done *after* the WMM parameter configuration
function was called.

This leads to unreliability in the driver getting properly configured on first
association (depending on what counter value the AP happens to use.) When
disassociating (the wmm default parameters are configured to the driver) and
then reassociating, due to the above the WMM configuration is not set to the
driver at all.

On drivers without beacon filtering the problem is corrected by later beacons,
but on drivers with beacon filtering the WMM will remain permanently incorrectly
configured.

Fix this by moving the initialization of wmm_last_param_set to -1 before
ieee80211_sta_wmm_params is called on association.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IBSS started from wireless extensions is currently
missing basic rate configuration, fix this by moving
the code to generate the default to the common code
that gets invoked for both nl80211 and wext.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug in the driver which was
exposed by CONFIG_USB_DEBUG:
	"usb 1-1.6.3: BOGUS urb flags, 40 --> 0"

The transfer flag "URB_ZERO_PACKET" is only valid
for bulk urbs.

Reported-by: André Erdmann
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As reported by Ryan Niemi, some bitmasks in the register definition for the PCU
Diagnostic register (DIAG_SW) were missing a zero at the end. While at it fix
some typos and add more comments.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code in ath5k_hw_get_tsf64() is time critical and will return wrong results
if we get interrupted, so disable local interrupts.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We use FUDGE to make sure the next TBTT is ahead of the current TU.
Since we later substract AR5K_TUNE_SW_BEACON_RESP (10) in the timer
configuration we need to make sure it is bigger than that.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds sanity-checks for the beacon timers and especially the ATIM
window to ath5k. It is basically the same what i did for madwifi two years ago
and fixes a problem in IBSS mode which has been described as "ramping" pings.

See the code comments for a more detailed description and these links:

http://madwifi-project.org/ticket/1154
http://madwifi-project.org/changeset/3867
http://thread.gmane.org/gmane.linux.drivers.madwifi.devel/6066Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not used and it's unlikely we will ever implement ATIM.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

David Miller complained about the driver's excessive use
of variables in __packed structs. While I did not fully
agree with his sole "performance" argument on all accounts.
I do see some room for improvement in hot-paths on
architectures without an efficient access to unaligned
elements.

This first patch (dare I say?) optimizes an important tx
hot-path in the driver: carl9170_tx_prepare.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>