This patch addresses a long standing issue of the driver with the
mac80211 .flush() callback. Since implementing the .flush() callback
a number of issues have been fixed, but a WARN_ON_ONCE() was still
triggered because the timeout on the flush could still occur.

This patch changes the awkward design using msleep() into one using
a waitqueue. The waiting flush() context will kick the transmit dma
when it is idle and the timeout used waiting for the event is set
to 500 ms. Worst case there can be 64 frames outstanding for transmit
in the driver. At a rate of 1Mbps that would take 1.5 seconds assuming
MTU is 1500 bytes and ignoring retries. The WARN_ON_ONCE() is also
removed as this was put in to indicate the flush timeout as a reason
for the driver to stall. That was not happening since fixing endless
AMPDU retries with following upstream commit:

commit 85091fc0
Author: Arend van Spriel <arend@broadcom.com>
Date:   Thu Feb 23 18:38:22 2012 +0100

    brcm80211: smac: fix endless retry of A-MPDU transmissions

bugzilla: 42840 <https://bugzilla.kernel.org/show_bug.cgi?id=42840>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=799168>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=787649>

Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Camaleón <noelamac@gmail.com>
Cc: Milan Bouchet-Valat <nalimilan@club-internet.fr>
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unregisters the gpio chip before ssb gets unloaded.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch unregisters the gpio chip before bcma gets unloaded.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reported-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel commits 41affd52 and 6539306b changed the locking in rtl_lps_leave()
from a spinlock to a mutex by doing the calls indirectly from a work queue
to reduce the time that interrupts were disabled. This change was fine for
most systems; however a scheduling while atomic bug was reported in
https://bugzilla.redhat.com/show_bug.cgi?id=903881. The backtrace indicates
that routine rtl_is_special(), which calls rtl_lps_leave() in three places
was entered in atomic context. These direct calls are replaced by putting a
request on the appropriate work queue.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: NNathaniel Doherty <ntdoherty@gmail.com>
Cc: Nathaniel Doherty <ntdoherty@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is normal for minidrivers accumulating frames to return NULL
from their tx_fixup function. We do not want to count this as a
drop, or log any debug messages.  A different exit path is
therefore chosen for such drivers, skipping the debug message
and the tx_dropped increment.

The test for accumulating drivers was however completely bogus,
making the exit path selection depend on whether the user had
enabled tx_err logging or not. This would arbitrarily mess up
accounting for both accumulating and non-accumulating minidrivers,
and would result in unwanted debug messages for the accumulating
drivers.

Fix by testing for FLAG_MULTI_PACKET instead, which probably was
the intention from the beginning.  This usage match the documented
behaviour of this flag:

 Indicates to usbnet, that USB driver accumulates multiple IP packets.
 Affects statistic (counters) and short packet handling.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) rhine_tx() should use dev_kfree_skb() not dev_kfree_skb_irq()

2) rhine_slow_event_task's NAPI triggering logic is racey, it
   should just hit the interrupt mask register.  This is the
   same as commit 7dbb4918
   ("r8169: avoid NAPI scheduling delay.") made to fix the same
   problem in the r8169 driver.  From Francois Romieu.
Reported-by: NJamie Gloudon <jamie.gloudon@gmail.com>
Tested-by: NJamie Gloudon <jamie.gloudon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to C_CAN documentation, the reserved bit in IFx_MASK2 register is
fixed 1.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add VID, PID and fixed interface for Telit LE920
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.

Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs.  Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.

If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.

We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.

Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state.  Correct this by
setting netif_carrier_off on probe, like other drivers do.

Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway

Tested successfully by myself
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions.  Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors.  Correctable errors will be handled
by the hardware.  Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded.  If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error.  The driver will then reset the hardware in order to
clear the error and restart.

Both types of errors will be accounted for in statistics counters.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When bonding module is loaded with primary parameter and one decides to unset
primary slave using sysfs these settings are not preserved during bond device
restart. Primary slave is only unset once and it's not remembered in
bond->params structure. Below is example of recreation.

 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=active-backup miimon=100 primary=eth01"
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)

 echo "" > /sys/class/net/bond0/bonding/primary
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None

 sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0
 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond
BONDING_OPTS="mode=active-backup miimon=100 "
 ifdown bond0 && ifup bond0

without patch:
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)

with patch:
 grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NMilos Vyletel <milos.vyletel@sde.cz>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We forbid polling, writing and reading when the file were detached, this may
complex the user in several cases:

- when guest pass some buffers to vhost/qemu and then disable some queues,
  host/qemu needs to do its own cleanup on those buffers which is complex
  sometimes. We can do this simply by allowing a user can still write to an
  disabled queue. Write to an disabled queue will cause the packet pass to the
  kernel and read will get nothing.
- align the polling behavior with macvtap which never fails when the queue is
  created. This can simplify the polling errors handling of its user (e.g vhost)

We can simply achieve this by don't assign NULL to tfile->tun when detached.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the polling errors were ignored, which can lead following issues:

- vhost remove itself unconditionally from waitqueue when stopping the poll,
  this may crash the kernel since the previous attempt of starting may fail to
  add itself to the waitqueue
- userspace may think the backend were successfully set even when the polling
  failed.

Solve this by:

- check poll->wqh before trying to remove from waitqueue
- report polling errors in vhost_poll_start(), tx_poll_start(), the return value
  will be checked and returned when userspace want to set the backend

After this fix, there still could be a polling failure after backend is set, it
will addressed by the next patch.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when vhost_init_used() fails the sock refcnt and ubufs were
leaked. Correct this by calling vhost_init_used() before assign ubufs and
restore the oldsock when it fails.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c8d68e6b removed carrier off call
from tun_detach since it's now called on queue disable and not only on
tun close.  This confuses userspace which used this flag to detect a
free tun. To fix, put this back but under if (clean).
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Tested-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Tested-by: NToralf Förster <toralf.foerster@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:

[  588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[  588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[  588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[  588.286208] ieee80211 phy0: Hardware restart was requested

The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.

Bisecting was done by Seth Forshee and showed following commit as the
culprit:

commit 57fe5048
Author: Piotr Haber <phaber@broadcom.com>
Date:   Wed Nov 28 21:44:07 2012 +0100

    brcmsmac: fix bounds checking in tx/rx

[1] http://www.spinics.net/lists/linux-wireless/msg101293.htmlReported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.

BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: NSuravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: NBorislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: NJoerg Roedel <joro@8bytes.org>

dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.

This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.

Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: NAnunay Saxena <anunay.saxena@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.

VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Spotted-by: NTimo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 9992c2e2 (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant.  The USB core has already done the lookup
and saved the result in the USB interface struct.  Use that
instead.

Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Greear reported crashes in ip_rcv_finish() on a stress
test involving many macvlans.

We tracked the bug to a dst use after free. ip_rcv_finish()
was calling dst->input() and got garbage for dst->input value.

It appears the bug is in loopback driver, lacking
a skb_dst_force() before calling netif_rx().

As a result, a non refcounted dst, normally protected by a
RCU read_lock section, was escaping this section and could
be freed before the packet being processed.

  [<ffffffff813a3c4d>] loopback_xmit+0x64/0x83
  [<ffffffff81477364>] dev_hard_start_xmit+0x26c/0x35e
  [<ffffffff8147771a>] dev_queue_xmit+0x2c4/0x37c
  [<ffffffff81477456>] ? dev_hard_start_xmit+0x35e/0x35e
  [<ffffffff8148cfa6>] ? eth_header+0x28/0xb6
  [<ffffffff81480f09>] neigh_resolve_output+0x176/0x1a7
  [<ffffffff814ad835>] ip_finish_output2+0x297/0x30d
  [<ffffffff814ad6d5>] ? ip_finish_output2+0x137/0x30d
  [<ffffffff814ad90e>] ip_finish_output+0x63/0x68
  [<ffffffff814ae412>] ip_output+0x61/0x67
  [<ffffffff814ab904>] dst_output+0x17/0x1b
  [<ffffffff814adb6d>] ip_local_out+0x1e/0x23
  [<ffffffff814ae1c4>] ip_queue_xmit+0x315/0x353
  [<ffffffff814adeaf>] ? ip_send_unicast_reply+0x2cc/0x2cc
  [<ffffffff814c018f>] tcp_transmit_skb+0x7ca/0x80b
  [<ffffffff814c3571>] tcp_connect+0x53c/0x587
  [<ffffffff810c2f0c>] ? getnstimeofday+0x44/0x7d
  [<ffffffff810c2f56>] ? ktime_get_real+0x11/0x3e
  [<ffffffff814c6f9b>] tcp_v4_connect+0x3c2/0x431
  [<ffffffff814d6913>] __inet_stream_connect+0x84/0x287
  [<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
  [<ffffffff8108d695>] ? _local_bh_enable_ip+0x84/0x9f
  [<ffffffff8108d6c8>] ? local_bh_enable+0xd/0x11
  [<ffffffff8146763c>] ? lock_sock_nested+0x6e/0x79
  [<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
  [<ffffffff814d6b49>] inet_stream_connect+0x33/0x49
  [<ffffffff814632c6>] sys_connect+0x75/0x98

This bug was introduced in linux-2.6.35, in commit
7fee226a (net: add a noref bit on skb dst)

skb_dst_force() is enforced in dev_queue_xmit() for devices having a
qdisc.
Reported-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a cpu notifier to virtio-net, so that we can reset the
virtqueue affinity if the cpu hotplug happens. It improve
the performance through enabling or disabling the virtqueue
affinity after doing cpu hotplug.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split out the clean affinity function to virtnet_clean_affinity().

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As Michael mentioned, set affinity and select queue will not work very
well when CPU IDs are not consecutive, this can happen with hot unplug.
Fix this bug by traversal the online CPUs, and create a per cpu variable
to find the mapping from CPU to the preferable virtual-queue.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Updated in latest datasheet.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

If the twl4030_write_script function gets called with
a zero length argument, its return value does not
get set. We know that all scripts have a nonzero
length, but returning an error in case they ever
do is probably appropriate.

Without this patch, building omap2plus_defconfig results in:

drivers/mfd/twl4030-power.c: In function 'load_twl4030_script':
drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: NAmit Kucheria <amit.kucheria@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: "Kristo, Tero" <t-kristo@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.

The failure case is where this unwanted write transfers incorrect data to
a critical register.

This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Different card reader has different method to switch output voltage, so
we have to use the callback function provided by MFD driver to switch
output pad voltage.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NOlivier Sobrie <olivier@sobrie.be>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].

Cc: linux-stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: NOlivier Sobrie <olivier@sobrie.be>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>