Add MIPS dependency for dm9000 ethernet controller.  Indeed this controller
is used by some embedded platforms based on MIPS CPUs.
Signed-off-by: NFranck Bui-Huu <franck.bui@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

A BIOS bug affecting some multiport tulip NICs requires an irq fixup
in tulip_core.c.  This has only been enabled for i686, but it is
needed for x86_64 as well.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Disable TX status deferral (EMACx_MR[MWSW=001]) in half-duplex mode.
I have two reports when EMAC stops transmitting when connected to a
hub. TX ring debug printouts show complete mess when this happens,
probably hardware collision handling doesn't work quite well in this
mode.

This is relevant only for SoCs with EMAC4 core (440GX, 440SP, 440SPe).
Tested on 440GX.
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Don't enable the pci device twice (already done in the probe
routine).  Propogate the error codes from pci_request_region
back to initial probing.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The sk98lin driver doesn't do proper error number handling
during initialization. Note: -EAGAIN is a bogus return value for
hardware errors.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Trivial use of kzalloc.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Sk98lin driver error recovery on two port boards is bad.
If it fails the second allocation, it will not release resources
properly. Also it registers the second port in the pci driver data

If second port fails, might as well go with one port.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Sk98lin 64bit memory handling is wrong. It doesn't set the
highdma flag; i.e. the kernel always does bounce buffers.
It doesn't fallback to 32 bit mask if it can't get 64 bit mask.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Sk98lin driver has a routine marked __init that is called from
the probe code. If using pci hotplug, this could be called after
the initialization so it needs to be marked __devinit.
So if you hot added a sk98lin board, the kernel would crash.
I don't have hot plug hardware to actually try this feat.

Also, there are two routines, only called from SkGeBoardInit that can
be marked __devinit.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Since version 4.1 the gcc is warning about ignored attributes. This patch is
using the equivalent attribute on the struct instead of on each of the
structure or union members.

GCC Manual:
  "Specifying Attributes of Types

   packed
    This attribute, attached to struct or union type definition, specifies
    that
    each member of the structure or union is placed to minimize the memory
    required. When attached to an enum definition, it indicates that the
    smallest integral type should be used.

    Specifying this attribute for struct and union types is equivalent to
    specifying the packed attribute on each of the structure or union
    members."
Signed-off-by: NJan Blunck <jblunck@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels.  For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.

Currently, ARM drivers do (eg) the following:

	err = request_irq(irq, ...);

	set_irq_type(irq, IRQT_RISING);

However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.

Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt.  The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.

Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like.  The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The Kconfig symbol for pnx0105 was recently renamed to ARCH_PNX010X.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

PNX010X support for CS89x0 should be conditional on NET_PCI, as it is an 'on
board controller' and NET_PCI includes that category of NICs.  Since
ARCH_PNX0105 was recently changed to ARCH_PNX010X, incorporate that change as
well while we're at it.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement readwords/writewords that use readword/writeword, and switch the
rest of the driver over to use these.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Implement suitable versions of the readword/writeword macros for ixdp2x01 and
pnx0501.  Handle the 32-bit spacing of the registers in these functions
instead of in the header file.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make readreg/writereg use readword/writeword.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Reverse the order of readreg/writereg and readword/writeword in the
file, so that we can make readreg/writereg use readword/writeword.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Switch all occurences of inw/outw in the driver over to readword/writeword.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

readword() and writeword() take a 'struct net_device *' and deref its
->base_addr member.  Make them take the base_addr directly instead, so
that we can switch the other occurences of inw/outw in the file over
to readword/writeword as well.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Cc: dmitry pervushin <dpervushin@ru.mvista.com>
Cc: <dsaxena@plexity.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The unlocking disappeared during commit
5793f4be.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Small cleanup of includes meant for older implementation.
Signed-off-by: NMarko Kohtala <marko.kohtala@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Sanitize some s390 Kconfig options.  We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT.  Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.

With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:

        int (*probe)            (struct pcmcia_device *dev);
        void (*remove)          (struct pcmcia_device *dev);

        int (*suspend)          (struct pcmcia_device *dev);
        int (*resume)           (struct pcmcia_device *dev);
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.

Bugfix to include/pcmcia/ds.c
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

It is no longer needed, so let's remove it, saving a bit of memory.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Stephen Hemminger <shemminger@osdl.org>

is_multicast_ether_addr() accepts broadcast too, so the
is_broadcast_ether_addr() calls are redundant.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turning struct iphdr::tot_len into __be16 added sparse warning.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And actually, with this, the whole pppox layer can basically
be removed and subsumed into pppoe.c, no other pppox sub-protocol
implementation exists and we've had this thing for at least 4
years.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.

Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Its common enough to to justify that, TCP still can't use it as it has the
prequeueing stuff, still to be made generic in the not so distant future :-)
Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As everyone knows, the rule is: "i before e.. um.. always."
Signed-off-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Ignore all files generated from *_shipped files, plus a few others.
Signed-off-by: NBrian Gerst <bgerst@didntduck.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1).  Retested.  Problem remains fixed.

Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the checks are scattered all over and this leads
to inconsistencies and even cases where the check is not made.

Based upon a patch from Kris Katterjohn.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two critical bugs were found in forcedeth 0.47:
 - TSO doesn't work.
 - pci_map_single() for the rx buffers is called with size==0.  This bug
   is critical, it causes random memory corruptions on systems with an
   iommu.

Below is a minimal fix for both bugs, for 2.6.15.

TSO will be fixed properly in the next version.  Tested on x86-64.
Signed-Off-By: NManfred Spraul <manfred@colorfullife.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Andy,

libphy has no license tag. Something like the attached (untested!) patch
is needed. Hopefully such a change finds its way into 2.6.15.

filename: /lib/modules/2.6.15-rc5-3-ppc64/kernel/drivers/net/phy/libphy.ko
vermagic:       2.6.15-rc5-3-ppc64 SMP gcc-4.1
depends:
srcversion:     ACC921B5E82701BE1E6F603

 drivers/net/phy/phy_device.c |    4 ++++
 1 files changed, 4 insertions(+)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add ID for Symbol LA-4123.  Reported by Tomas Novak <tap@post.cz>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>