88PM860x codec is used in Marvell saarb development board. 88PM860x codec
is used as master mode for SSP communication. Only I2S format is supported.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add 88PM860x codec driver. 88PM860x codec supports two interfaces. And it
also supports headset/mic/hook/short detection.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since the SSC is already being registered as a device under arch and
the DMA and SSC hardware are pretty much the same provide a simplified
device registration function for the Atmel SSC which will add the
ASoC-specific devices within the ASoC code, parenting the SSC device
off the actual SSC device. Also use it in the sam9g20-ek driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

A couple of typos in the multi-component conversion.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Instead of unconditionally enabling the crystal oscillator on the WM8731
only enable it when explicitly selected via set_sysclk(), allowing machine
drivers to specify that they drive a clock into MCLK alone. This avoids
any conflicts between the oscillator and the external MCLK source and saves
power for systems which do not need the oscillator.

This should also deliver a small power saving on systems using the crystal
since the oscillator will only be enabled when the ADC or DAC is active.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Output size_t type as a "%Zu" to avoid warnings.
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Dead pxa2xx-pcm.h includes and a missing ,
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch contains two small fixes for the sound board driver for the qi_lb60
introduced by the multi-component patches:
* Remove unnecessary includes: Those includes where only used to get the
  definitions for the DAI devices and are thus not needed anymore.
* Fix a typo.
Signed-off-By: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Reported-by: NSeungwhan Youn <claude.youn@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The RX and TX directions were inverted.
Reported-by: NSeungwhan Youn <claude.youn@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This is not supported by current hardware revisions.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

The DAC OSR should be selected based on the sample clock ratio.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Drive a minimal supported number of clocks required for the current
bit format in master mode. In slave mode this setting has no effect.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Implement set_sysclk() and then rather than assuming 256fs use the
supplied value to calculate and configure the clock ratio for the
currently used sample rate. As a side effect we also end up
implementing clock selection for the ADC path.

In order to avoid confusion remove the existing set_clkdiv() based
configuration of the clock source for the DAC and update the SMDK64xx
driver (which is the only in-tree user of the CODEC).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In the case of the BCLK rate the defines are at best misleading anyway.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

All the cool kids are using snd_soc_update_bits() these days.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

There's much more needed but this'll get us started.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

SCFR bit is required to be always set if pxa ssp is in slave mode. This bit
indicates clock input to SSPSCLK is only active during data transfers.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since pxa2xx-pcm.h is removed from sound/soc/pxa, we need to update the
path in related files.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Tested-by: NIan Lartey <ian@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

 Removed #include of pxa2xx-pcm.h
Signed-off-by: NIan Lartey <ian@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since the core now includes deduplication in the name of CODEC
devices there's no need to add extra for the debugfs directory name.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Since the debugfs directory is current per CODEC we should only init
it when the CODEC is initialised, otherwise we end up with errors
being generated when an attempt is made to add duplicate debugfs
entries.

Since most of this stuff is actually for the card we should refactor
but this can come later.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Gcc complains that ret might be used uninitialized:

sound/usb/format.c: In function ‘snd_usb_parse_audio_format’:
sound/usb/format.c:354: warning: ‘ret’ may be used uninitialized in this function
sound/usb/format.c:354: note: ‘ret’ was declared here
sound/usb/format.c:414: warning: ‘ret’ may be used uninitialized in this function
sound/usb/format.c:414: note: ‘ret’ was declared here

I suppose it could be uninitialized if there is ever a UAC_VERSION_3
released. Anyway this patch is worthwhile if only to silence the gcc
warning.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Any subsequent revisions will have these configuration changes applied
by default.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Change the chip defaults to optimise performance of some of the DSP
functionality.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The commit eb541337
    ALSA: hda - Make converter setups sticky
changes the semantics of snd_hda_codec_cleanup_stream() not to clean up
the stream at that moment but delay the action.  This broke the codes
expecting that the clean-up is done immediately, such as dynamic ADC
changes in some codec drivers.

This patch fixes the issue by introducing a lower helper,
__snd_hda_codec_cleanup_stream(), to allow the immediate clean up.
The original snd_hda_codec_cleanup_stream() is kept as is now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a device is plugged over HDMI, it passes some information in ELD
including the supported PCM parameters like formats, rates, channels.
This patch adds the check to PCM open callback of HDMI streams so that
only valid parameters the device supports are used.

When no device is plugged, the parameters the codec supports are used;
it's mostly all parameters the hardware can work.  This is for apps
that are started before device plugging and do probing (e.g. a sound
daemon), so that at least, probing would work even before the device
plugging.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Nothing should be referencing this any more.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>

No notable changes, currently build tested only.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add back the register restore call, when the codec driver is
removed.
This does not affect normal operation, but it is usefull when
debugging audio through the twl4030 class codecs.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Since the provision of a struct device for the CODEC is now mandatory
we can use container_of() to locate the struct i2c_client and struct
spi_device for relevant devices, removing the need to manually set it
in each driver.

A further patch will automate selection of the control type based on
the bus_type of the struct device, further reducing the amount of
driver code required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Now soc-cache.c can figure out the I2C and SPI control data from the
device for the CODEC we don't need to manually assign it in drivers.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Add support for adding "status = disabled" to an SSI node to incidate that it
is not wired on the board.  This replaces the not-so-intuitive previous method
of omitting a codec-handle property.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>