The documentation for the 8070 and 8072 SPCv chip explicitly states that
a minimum of 500ms must elapse before issuing commands, otherwise the
SPCv may not process them and the firmware may get into an unrecoverable
state requiring a reboot.  While the Linux guys will probably think this
is 'racy', it is called out in the chip documentation and inserting this
delay makes power management function properly.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

PHY profiles are not saved in NVRAM on ATTO 12Gb SAS controllers.
Therefore, in order for the controller to function in a wide range of
configurations, the PHY profiles must be statically set.  This patch
provides the necessary functionality to do so.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ATTO SAS controllers retrieve the SAS address from the NVRAM in a location
different from non-ATTO PMC Sierra SAS controllers.  This patch makes the
necessary adjustments in order to retrieve the SAS address on these types
of adapters.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These PCI IDs allow the pm8001 driver to load against ATTO 12Gb SAS
controllers that use PMC Sierra 8070 and PMC Sierra 8072 SAS chips.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These SAS controllers support speeds up to 12Gb.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Previuosly, all PMC Sierra 80xx controllers are assumed to be a
motherboard controller, except if the subsystem vendor ID was equal to
PCI_VENDOR_ID_ADAPTEC.  The driver then attempts to load PHY settings
from NVRAM.  While this may be correct behavior for most controllers, it
does not work with Adaptec and ATTO controllers since they do not store
PHY settings in NVRAM and choose to use either custom PHY settings or
chip defaults.  Loading random values from NVRAM may cause the
controllers to malfunction in this edge case.
Signed-off-by: NBenjamin Rood <brood@attotech.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete.  The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: NHannes Reinecke <hare@suse.de>

The task_collector mode (or "latency_injector", (C) Dan Willians) is an
optional I/O path in libsas that queues up scsi commands instead of
directly sending it to the hardware.  It generall increases latencies
to in the optiomal case slightly reduce mmio traffic to the hardware.

Only the obsolete aic94xx driver and the mvsas driver allowed to use
it without recompiling the kernel, and most drivers didn't support it
at all.

Remove the giant blob of code to allow better optimizations for scsi-mq
in the future.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Acked-by: NDan Williams <dan.j.williams@intel.com>

All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.

Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NVenkatesh Srinivas <venkateshs@google.com>

Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq.  This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

When a call to request_irq() failed pm8001_setup_msix()
still returns the success. This udate fixes the described
misbehaviour.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The driver ignores the return value in a lot of places, fix
it at least somewhere (and release the resources in such cases),
to avoid that bad things happen.
A memory leak is fixed too.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Patch adds a new spinlock to protect the ccb management.
It may happen that concurrent threads become the same tag value
from the 'alloc' function', the spinlock prevents this situation.
Signed-off-by: NTomas Henzl <thenzl@redhat.com>
Acked-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

During hibernation, the HBA firmware may lose power and forget the device
id info.   This causes the HBA to reject IO upon resume.   The fix is
to call the libsas power management routines to make the domain device
forgetful.

This fixes bug 76681: https://bugzilla.kernel.org/show_bug.cgi?id=76681Signed-off-by: NBradley Grove <bgrove@attotech.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The pm8001_get_phy_settings_info() function does not check
the kzalloc() return value and does not free the allocated memory.
Signed-off-by: NMaurizio Lombardi <mlombard@redhat.com>
Acked-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: NJack Wang <xjtuwjp@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

It's a NOOP since 2.6.35 and it will be removed one day.

[jejb: remove from missed arm scsi drivers]
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NBradley Grove <bgrove@attotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When multiple vectors are used, the vector variable is over written,
resulting in unhandled operation for those vectors.
This fix prevents the problem by maitaining HBA instance and
vector values for each irq.

[jejb: checkpatch fixes]
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Supports below logging facilities,
Inbound outbound queues dump.
Non fatal dump in case of IO failures.
Fatal dump in case of firmware failure.

[jejb: checkpatch spacing fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Phy profile implementation to support phy settings feature
for motherboard controllers.

[jejb: checkpatch fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Updated pci id table with device, vendor, subdevice and subvendor ids
for 8074, 8076, 8077 SAS/SATA 12G controllers. Added 12G related macros.

Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Acked-by: Nlindar_liu <lindar_liu@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: Anandkumar.Santhanam@pmcs.com
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Pci core has been saved pm cap register offset by pdev->pm_cap in
pci_pm_init() in init path. So we can use pdev->pm_cap instead of using
pci_find_capability(pdev, PCI_CAP_ID_PM) for better performance and simplified
code.
Tested-by: NLindar Liu <lindar_liu@usish.com>
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Acked-by: NLindar Liu <lindar_liu@usish.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas.  The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:

drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]

Fix by eliminating one of them.  The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Modified thermal configuration to happen after interrupt registration
Added SAS controller configuration during initialization
Added error handling logic to handle I_T_Nexus errors and variants

[jejb: fix up tabs and spaces issues]
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Individual WWN read operations based on controller.
PM8081 - Read WWN from Flash VPD.
PM8088/89 - Read WWN from EEPROM.
PM8001 - Read WWN from NVM.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Changed name in driver to pm80xx. Updated debug messages.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Performing pci_free_consistent in tasklet had result in a core dump. So
allocated a new memory region for it. Fix for passing proper address
and operation in firmware flash update.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Implementation of SPCv/ve specific hardware functionality and
macros. Changing common functionalities wrt SPCv/ve operations.
Conditional checks for SPC specific operations.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Implementation of interrupt handlers and tasklets to support
upto 64 interrupt for the device.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Update of function prototype for common function to SPC and SPCv/ve.
Multiple queues implementation for IO.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Memory allocation and configuration of multiple inbound and
outbound queues.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Updated pci id table with device, vendor, subdevice and subvendor ids
for 8081, 8088, 8089 SAS/SATA controllers. Added SPCv/ve related macros.
Updated macros, hba info structure and other structures for SPCv/ve.
Update of structure and variable names for SPC hardware functionalities.
Signed-off-by: NSakthivel K <Sakthivel.SaravananKamalRaju@pmcs.com>
Signed-off-by: NAnand Kumar S <AnandKumar.Santhanam@pmcs.com>
Acked-by: NJack Wang <jack_wang@usish.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

All memory regions are allocated based on variables total_len
and alignment but free was based on element_size.
Signed-off-by: NSakthivel K <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: NAnand Kumar S <DL.Team.PMC.SPC.Linux.open.source@pmcs.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>