TMIO MMC chips contain an SD / SDIO IP core from Panasonic, similar to
the one, used in MN5774 and other MN57xx controllers. These IP cores are
included in many multifunction devices, in sh-mobile chips from Renesas,
in the latter case they can also use DMA. Some sh-mobile implementations
also have some other specialities, that MFD-based solutions don't have.
This makes supporting all these features in a monolithic driver inconveniet
and error-prone. This patch splits the driver into 3 parts: the core,
the MFD glue and the DMA support. In case of a modular build, two modules
will be built: mmc_tmio_core and mmc_tmio.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch allows transferring of some requests in PIO and some in DMA
mode and defaults to using DMA only for transfers longer than 8 bytes.
This is especially useful with SDIO, which can have lots of 2- and 4-byte
transfers, creating unnecessary high overhead, when executed in DMA.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

On some SDHI tmio implementations the order of DMA and command completion
interrupts swaps, which leads to malfunction. This patch postpones
DMA activation until the MMC command completion IRQ time.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fix the NO INT in the Multi-BLK IO in SD/MMC, and Multi-BLK read in
SDIO on imx53.

The CMDTYPE of the CMD register (offset 0xE) should be set to "11"
when the STOP CMD12 is issued on imx53 to abort one open ended
multi-blk IO. Otherwise the TC INT wouldn't be generated.

In exact block transfer, the controller doesn't complete the
operations automatically as required at the end of the transfer
and remains on hold if the abort command is not sent on imx53.

As a result, the TC flag is not asserted and SW receives timeout
exception. Set bit1 of Vendor Spec register to fix it.
Signed-off-by: NRichard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add one flag to indicate the GPIO CD/WP is enabled or not
on imx platforms, and reuse the writel/readl as the general
APIs for imx SOCs.
Signed-off-by: NRichard Zhu <Hong-Xing.Zhu@freescale.com>
Reviewed-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add the abort CMDTYPE bits definition of command register (offset 0xE)
Signed-off-by: NRichard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

sdhci-esdhc-imx does not need SDHCI_QUIRK_NO_CARD_NO_RESET.
Make it OF-specific.
Signed-off-by: NRichard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Since these are the headers that provide irq_of_parse_and_map()
and NO_IRQ.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NChris Ball <cjb@laptop.org>

New IO FPGA implementation for Versatile Express boards contain
MMCI (PL180) cell with FIFO extended to 128 words (512 bytes).

Matt Waddel reports that this patch improves MMC performance on
his vexpress system, and also fixes "mmcblk0: error -5 transferring
data" errors.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Tested-by: NMatt Waddel <matt.waddel@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch uses the fixed burst bit when using an internal DMA controller.
I found increased performance with IDMAC when this bit is set.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The SDHCI driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it was not converted by commit 44c10138
(PCI: Change all drivers to use pci_device->revision). The newer VIA
driver has similar code too. This patch converts both drivers to use
the 'revision' field of 'struct pci_dev'.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: NHarald Welte <HaraldWelte@viatech.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This silences warnings such as

drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type

These were added by me in commit 2a79bb1d.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use mfd_data for passing information from mfd drivers to mfd
clients.  The mfd_cell's driver_data field is being phased out.

Clients that were using driver_data now access .mfd_data
via mfd_get_data().  This changes tmio-mmc only; mfd drivers with
other cells are not modified.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

No need to explicitly set the cell's platform_data/data_size.

Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use resource_size().
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for power regulators.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Nkyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch is related to re-init processing on suspend/resume.

When card is resuming, some register is reset.  If card is removable,
maybe controller should be rescan for card.  But if assume card is
non-removable, need to restore the old value at registers.

We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds quirks and capabilities to platdata.

Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Currently kunmap_atomic() doesn't take into account the offset, used
with kmap_atomic(). On platforms, where kunmap_atomic() is not a NOP,
this will lead to problems, when offset != 0.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

count is only ever used by assigning to old_len if count == 0, and
then old_len isn't ever used at all.  So, both are redundant.  Fixes:

drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_read_data_pio’:
drivers/mmc/host/dw_mmc.c:1034:32: warning: variable ‘old_len’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NWill Newton <will.newton@imgtec.com>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It can be worked around using a GPIO which will be done for i.MX later.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Tested-by: NMarc Reilly <marc@cpdesign.com.au>
Tested-by: NEric Benard <eric@eukrea.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

dma_unmap_sg() already flushes the cache, I don't get what this
code is doing here.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

To support MMC aggressive clock gating the driver has to stop the
interface clock when the .set_ios() method is called with .clock == 0.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds DDR mode support to dw_mmc.

If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode.  For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

drivers/mmc/host/via-sdmmc.c: In function ‘via_reset_pcictrl’:
drivers/mmc/host/via-sdmmc.c:805:8: warning: variable ‘addrbase’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

Fixes:

drivers/mmc/host/cb710-mmc.c: In function ‘cb710_wait_while_busy’:
drivers/mmc/host/cb710-mmc.c:182:6: warning: variable ‘err’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

drivers/mmc/host/sdhci-pci.c: In function ‘sdhci_pci_probe_slot’:
drivers/mmc/host/sdhci-pci.c:913:18: warning: variable ‘addr’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: NChris Ball <cjb@laptop.org>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.

Thanks Chris Ball for the indentation patch.
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Tested-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This variable doesn't seem to be used for anything after the
other patches so just drop it.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The host_sglen is now actually used to keep track of whether DMA
is active or not, so rename and retype it to bool.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>