Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We want to split old FS USB platform init code and stop doing pin multiplexing
under plat-omap. First move 24xx specific init code into omap2_usb[012]_init
functions.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Merge branch 'v2.6.35-rc3-iommu-for-next' of git://gitorious.org/~doyu/lk/mainline into omap-for-linus

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
  USB: gadget: f_mass_storage: stale common->fsg value bug fix
  USB: gadget: f_mass_storage: fixed fs descriptors not being updated
  USB: musb: Enable the maximum supported burst mode for DMA
  USB: musb: fix Blackfin ulpi stubs
  USB: MUSB: make non-OMAP platforms build with CONFIG_PM=y
  USB: musb_core: make disconnect and suspend interrupts work again
  USB: obey the sysfs power/wakeup setting
  USB: gadget eth: Fix calculate CRC32 in EEM
  USB: qcserial: fix a memory leak in qcprobe error path
  USB: gadget/printer, fix sleep inside atomic
  USB: isp1362-hcd, fix double lock
  USB: serial: ftdi: correct merge conflict with CONTEC id
  USB: fix oops in usb_sg_init()
  USB: s3c2410: deactivate endpoints before gadget unbinding
  USB: ehci-mxc: bail out on transceiver problems
  USB: otg/ulpi: bail out on read errors
  usb: musb: Fix a bug by making suspend interrupt available in device mode
  USB: r8a66597: Fix failure in change of status
  USB: xHCI: Fix bug in link TRB activation change.
  USB: gadget: g_fs: possible invalid pointer reference bug fixed
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: cpm_uart: implement the cpm_uart_early_write() function for console poll

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP: hwmod: Fix the missing braces
  OMAP4: clock: Fix multi-omap boot with reset un-used clocks
  OMAP3: PM: fix IO daisy chain enable to use PM_WKEN reg
  omap: GPIO: fix auto-disable of debounce clock
  omap: DMTIMER: Ack pending interrupt always when stopping a timer
  omap: Stalker board: switch over to gpio_set_debounce
  omap: fix build failure due to missing include dma-mapping.h
  omap iommu: Fix Memory leak

As discussed with Mike Reed, add him as the maintainer of the qla1280
driver as I no longer have any hardware and he is actively looking
after it.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

futex_find_get_task is currently used (through lookup_pi_state) from two
contexts, futex_requeue and futex_lock_pi_atomic.  None of the paths
looks it needs the credentials check, though.  Different (e)uids
shouldn't matter at all because the only thing that is important for
shared futex is the accessibility of the shared memory.

The credentail check results in glibc assert failure or process hang (if
glibc is compiled without assert support) for shared robust pthread
mutex with priority inheritance if a process tries to lock already held
lock owned by a process with a different euid:

pthread_mutex_lock.c:312: __pthread_mutex_lock_full: Assertion `(-(e)) != 3 || !robust' failed.

The problem is that futex_lock_pi_atomic which is called when we try to
lock already held lock checks the current holder (tid is stored in the
futex value) to get the PI state.  It uses lookup_pi_state which in turn
gets task struct from futex_find_get_task.  ESRCH is returned either
when the task is not found or if credentials check fails.

futex_lock_pi_atomic simply returns if it gets ESRCH.  glibc code,
however, doesn't expect that robust lock returns with ESRCH because it
should get either success or owner died.
Signed-off-by: NMichal Hocko <mhocko@suse.cz>
Acked-by: NDarren Hart <dvhltc@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On fsg_unbind the common->fsg pointer was not NULLed if the
unbound fsg_dev instance was the current one.  As an effect,
the incorrect pointer was preserved in all further operations
which caused do_set_interface to reference an invalid region.

This commit fixes this by raising an exception in fsg_bind
which will change the common->fsg pointer.  This also requires
an wait queue so that the thread in fsg_bind can wait till the
worker thread handles the exception.

This commit removes also a config and new_config fields of
fsg_common as they are no longer needed since fsg can be
used to determine whether function is active or not.

Moreover, this commit removes possible race condition where
the fsg field was modified in both the worker thread and
form various other contexts.  This is fixed by replacing
prev_fsg with new_fsg.  At this point, fsg is assigned only
in worker thread.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The full speed descriptors were copied to the usb_function structure
in the fsg_bind_config function before call to the usb_ep_autoconfig.
The usb_ep_autoconfig was called in fsg_bind using the original
descriptors.  In effect copied descriptors were not updated.

This patch changes the copy full speed descriptors after the call to
usb_op_autoconfig is performed.  This way, copied full speed
descriptors have updated values.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: NDries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Tested-by: NDries Van Puymbroeck <Dries.VanPuymbroeck@dekimo.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Setting MUSB Burst Mode 3 automatically enables support for
lower burst modes (BURST4, BURST8, BURST16 or bursts of unspecified
length). There is no need to set these burst modes based on the
packet size. Also enable the burst mode for both mode1 and mode0.

This is a fix for buggy hardware - having the lower burst modes
enabled can potentially cause lockups of the DMA engine used in
OMAP2/3/4 chips.
Signed-off-by: NHema HK <hemahk@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The new ulpi code defines fallback stubs for the Blackfin arch, but does
so incorrectly leading to a build failure:
drivers/usb/musb/musb_core.c:227: error: 'musb_ulpi_read' undeclared here (not in a function)
drivers/usb/musb/musb_core.c:228: error: 'musb_ulpi_write' undeclared here (not in a function)

Tweak the fallback stubs so that they do work as intended.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Attempt to build MUSB driver with CONFIG_PM=y (e.g. in the OTG mode) on DaVinci
results in these link errors:

drivers/built-in.o: In function `musb_restore_context':
led-triggers.c:(.text+0x714d8): undefined reference to
`musb_platform_restore_context'
drivers/built-in.o: In function `musb_save_context':
led-triggers.c:(.text+0x71788): undefined reference to
`musb_platform_save_context'

This turned out to be caused by commit 9957dd97
(usb: musb: Fix compile error for omaps for musb_hdrc). Revert it, taking into
account the rename of CONFIG_ARCH_OMAP34XX into CONFIG_ARCH_OMAP3 (which that
commit fixed in a completely inappropriate way) and the recent addition of
OMAP4 support.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 1c25fda4 (usb: musb: handle irqs in the
order dictated by programming guide) forgot to get rid of the old 'STAGE0_MASK'
filter for calling musb_stage0_irq(), so now disconnect and suspend interrupts
are effectively ignored...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1403) is a partial reversion of an earlier change
(commit 5f677f1d "USB: fix remote
wakeup settings during system sleep").  After hearing from a user, I
realized that remote wakeup should be enabled during system sleep
whenever userspace allows it, and not only if a driver requests it
too.

Indeed, there could be a device with no driver, that does nothing but
generate a wakeup request when the user presses a button.  Such a
device should be allowed to do its job.

The problem fixed by the earlier patch -- device generating a wakeup
request for no reason, causing system suspend to abort -- was also
addressed by a later patch ("USB: don't enable remote wakeup by
default", accepted but not yet merged into mainline).  The device
won't be able to generate the bogus wakeup requests because it will be
disabled for remote wakeup by default.  Hence this reversion will not
re-introduce any old problems.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CRC should be calculated for Ethernet frame, not for whole recievede EEM data.
This bug shows rarely, because in many times len == skb->len.
Signed-off-by: NJiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds missing kfree(data) before return -ENODEV.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Stanse found that sleep is called inside atomic context created by
lock_printer_io spinlock in several functions. It's used in process
context only and some functions sleep inside its critical section. As
this is not allowed for spinlocks, switch it to mutex.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Craig W. Nadler <craig@nadler.us>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Stanse found that isp1362_sw_reset tries to take a isp1362_hcd->lock,
but it is already held in isp1362_hc_stop. Avoid that by introducing
__isp1362_sw_reset which doesn't take the lock and call it from
isp1362_hc_stop. isp1362_sw_reset is then as simple as lock --
__isp1362_sw_reset -- unlock.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.

I believe the merge problem occurred with the commit:
dee5658b

Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: NDaniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1401) fixes a bug in usb_sg_init() that can cause an
invalid pointer dereference.  An inner loop reuses some local variables
in an unsafe manner, so new variables are introduced.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Gadget disconnect must be called before unbinding to avoid races.
The change fixes an oops on g_ether module unregistering.
Signed-off-by: NVladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The old code registered the hcd even if there were no transceivers
detected, leading to oopses like this if we try to probe a non-existant
ULPI:

[    2.730000] mxc-ehci mxc-ehci.0: unable to init transceiver
[    2.740000] timeout polling for ULPI device
[    2.740000] timeout polling for ULPI device
[    2.750000] mxc-ehci mxc-ehci.0: unable to enable vbus on transceiver
[    2.750000] mxc-ehci mxc-ehci.0: Freescale On-Chip EHCI Host Controller
[    2.760000] mxc-ehci mxc-ehci.0: new USB bus registered, assigned bus number 2
[    2.770000] Unhandled fault: external abort on non-linefetch (0x808) at 0xc4876184
[    2.770000] Internal error: : 808 [#1] PREEMPT
[    2.770000] last sysfs file:
[    2.770000] Modules linked in:
[    2.770000] CPU: 0    Not tainted  (2.6.33.5 #5)
[    2.770000] PC is at ehci_hub_control+0x4d4/0x8f8
[    2.770000] LR is at ehci_mxc_setup+0xbc/0xdc
[    2.770000] pc : [<c0196dfc>]    lr : [<c019bc8c>]    psr: 00000093
[    2.770000] sp : c3815e40  ip : 00000001  fp : 60000013
[    2.770000] r10: c4876184  r9 : 00000000  r8 : c3814000
[    2.770000] r7 : c391d2cc  r6 : 00000001  r5 : 00000001  r4 : 00000000
[    2.770000] r3 : 80000000  r2 : 00000007  r1 : 80000000  r0 : c4876184
[    2.770000] Flags: nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM Segment kernel
[    2.770000] Control: 0005317f  Table: a0004000  DAC: 00000017
[    2.770000] Process swapper (pid: 1, stack limit = 0xc3814270)
...
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable <stable@kernel.org>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

otg_read may return errnos, so bail out correctly to prevent bogus
ID-numbers.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As a part of aligning the ISR code for MUSB with the specs, the
ISR code was re-written. 

See Commit 1c25fda4 (usb: musb: handle 
irqs in the order dictated by programming guide)

With this the suspend interrupt came accidently under CONFIG_USB_MUSB_HDRC_HCD.

The fix brings suspend interrupt handling outside 
CONFIG_USB_MUSB_HDRC_HCD.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the change by 749da5f8,
The change in the status when the USB device is connected is wrong.
Therefore, the device is not recognized.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Paul Mundt" <lethal@linux-sh.org>
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 6c12db90 introduced a bug for
control transfers.  The patch was supposed to change when the link TRBs at
the end of each ring segment were given to the hardware.  If a transfer
descriptor (TD) ended just before the link TRB, the code wouldn't give
back the link TRB to the hardware; instead it would be given back in
prepare_ring() just before the next TD was enqueued at the top of the
ring.

Unfortunately, the code relied on checking the chain bit of the TRB to
determine whether the TD ended just before the link TRB.  It assumed that
the ring enqueuing code would call prepare_ring() before enqueuing the
next TD.  However, control transfers are made of multiple TDs, and
prepare_ring() is only called once before enqueuing two or three TDs.

If the first or second TD of the control transfer ended just before the
link TRB, then the code in inc_enq() would not move the enqueue pointer
past the link TRB, and the link TRB would get overwritten.  This would
cause the xHCI driver to start writing to memory past the ring segment,
and eventually the system would crash or hang.

The fix is to add a flag to inc_enq() that says whether the caller will
enqueue more TDs before calling prepare_ring().  If the chain bit is
cleared (meaning this is the last TRB in a TD), and the caller will not
enqueue more TDs, then we defer giving back the link TRB.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

During __gfs_do_config() some invalid pointers may be left
in usb_configuration::interfaces array from previous calls
to the __gfs_do_config() for the same configuration.  This
will always happen if an user space function which has
a fewer then the last user space function registers itself.
Composite's set_config() function that a pointer after the
last interface in usb_configuration::interface is NULL
unless the array is full.

This patch makes the __gfs_do_config() make sure that if the
usb_configuration::interface is not full then a pointer
after the last interface is NULL.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Call put_tty_driver() in cleanup function, to fix Oops when trying to open
gadget serial char device after module unload.
Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

No longer set low_latency flag as it causes this warning backtrace:

  WARNING: at kernel/mutex.c:207 __mutex_lock_slowpath+0x6c/0x288()

Fix associated locking and wakeups.
Signed-off-by: NJon Povey <jon.povey@racelogic.co.uk>
Cc: Maulik Mankad <x0082077@ti.com>
Cc: stable <stable@kernel.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The cpm_uart_early_write() function which was used for console poll
isn't implemented in the cpm uart driver.

Implementing this function both fixes the build when CONFIG_CONSOLE_POLL
is set and allows kgdboc to work via the cpm uart.
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: NBruce Ashfield <bruce.ashfield@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a lockdep-splat-causing regression introduced by commit 989a2979
("fasync: RCU and fine grained locking").

kill_fasync() can be called from both process and hard-irq context, so
fa_lock must be taken with IRQs disabled.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16230Reported-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: NDominik Brodowski <linux@dominikbrodowski.net>
Tested-by: NDominik Brodowski <linux@dominikbrodowski.net>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The os-linux/mem.c file calls fchmod function, which is declared in sys/stat.h
header file, so include it.  Fixes build breakage under FC13.
Signed-off-by: NLiu Aleaxander <Aleaxander@gmail.com>
Acked-by: NBoaz Harrosh <bharrosh@panasas.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a nuc900 lcd build error.

Since the 'nuc900_driver_clksrc_div()' API cannot be merged into mainline
successfully, I removed this clock source selection hook in this driver.
This means nuc900 lcd driver has to select default clock source from the
external crystal now.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Cc: Qiang Wang <rurality.wq@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A call to sysv_write_inode() in sysv_new_inode() to its new interface that
replaced wait flag with writeback structure.  This was broken by
a9185b41 ("pass writeback_control to
->write_inode").
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@kernel.org>		[2.6.34.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update Kconfig and Makefile in drivers/gpio to discourage inappropriate
addition of platform-specific code.

[akpm@linux-foundation.org: fix tpyo]
Signed-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ds1307 driver misreads the ds1388 registers when checking for 12 or 24
hour mode.  Instead of checking the hour register it reads the minute
register.  Therefore the driver thinks minutes >= 40 has the 12HR bit set
and resets the minute register by zeroing the high bits.  This results in
minutes are reset to 0-9, jumping back in time 40 or 50 minutes.  The time
jump is also written back to the RTC.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I take over the maintenance of SPI, USART, Ethernet and USB gadget
drivers.  Those drivers are found in Atmel microcontrollers, both
AT32/AVR32 and AT91/ARM.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Masami Hiramatsu moved back to Hitachi Japan and changed his email
address.
Signed-off-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a regression introduced by ae74e823 ("ipmi: add parameter to limit
CPU usage in kipmid").

Some systems were seeing CPU usage go up dramatically with the recent
changes to try to reduce timer usage in the IPMI driver.  This was traced
down to schedule_timeout_interruptible(1) being changed to
schedule_timeout_interruptbile(0).  Revert that part of the change.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16147Reported-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Tested-by: NThomas Jarosch <thomas.jarosch@intra2net.com>
Cc: <stable@kernel.org>		[2.6.34.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>