At least on i386, building with allyesconfig doesn't enable
PREEMPT, causing cec_gpio to not build.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There aren't many things that would be needed to allow it
to build with compile test.

Add the needed bits.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There are several functions that are used only inside the
driver. Stop exposing that to global symbolspace.

Get rid of the following gcc warnings:

drivers/media/platform/fsl-viu.c:240:17: warning: no previous prototype for ‘format_by_fourcc’ [-Wmissing-prototypes]
 struct viu_fmt *format_by_fourcc(int fourcc)
                 ^~~~~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:253:6: warning: no previous prototype for ‘viu_start_dma’ [-Wmissing-prototypes]
 void viu_start_dma(struct viu_dev *dev)
      ^~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:262:6: warning: no previous prototype for ‘viu_stop_dma’ [-Wmissing-prototypes]
 void viu_stop_dma(struct viu_dev *dev)
      ^~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:807:5: warning: no previous prototype for ‘vidioc_g_fbuf’ [-Wmissing-prototypes]
 int vidioc_g_fbuf(struct file *file, void *priv, struct v4l2_framebuffer *arg)
     ^~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:818:5: warning: no previous prototype for ‘vidioc_s_fbuf’ [-Wmissing-prototypes]
 int vidioc_s_fbuf(struct file *file, void *priv, const struct v4l2_framebuffer *arg)
     ^~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c: In function ‘viu_open’:
drivers/media/platform/fsl-viu.c:1170:6: warning: variable ‘status_cfg’ set but not used [-Wunused-but-set-variable]
  u32 status_cfg;
      ^~~~~~~~~~
drivers/media/platform/fsl-viu.c: At top level:
drivers/media/platform/fsl-viu.c:1304:6: warning: no previous prototype for ‘viu_reset’ [-Wmissing-prototypes]
 void viu_reset(struct viu_reg *reg)
      ^~~~~~~~~
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The isp_xclk_init_data const data isn't used anywere.

drivers/media/platform/omap3isp/isp.c:294:35: warning: ‘isp_xclk_init_data’ defined but not used [-Wunused-const-variable=]
 static const struct clk_init_data isp_xclk_init_data = {
                                   ^~~~~~~~~~~~~~~~~~

Fixes: 9b28ee3c ("[media] omap3isp: Use the common clock framework")
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

RFC 4122 asks for letters a-f in UUID to be lowercase. Follow this
recommendation.

Suggested by Paul Dagnelie at:
https://savannah.nongnu.org/bugs/index.php?53569Signed-off-by: NJean Delvare <jdelvare@suse.de>

OEM strings are defined by each OEM and they contain customized and
useful OEM information. Supporting it provides more flexible uses of
the dmi_matches function.
Signed-off-by: NAlex Hung <alex.hung@canonical.com>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

The test which ensures that the DMI type 1 structure is long enough
to hold the UUID is off by one. It would fail if the structure is
exactly 24 bytes long, while that's sufficient to hold the UUID.

I don't expect this bug to cause problem in practice because all
implementations I have seen had length 8, 25 or 27 bytes, in line
with the SMBIOS specifications. But let's fix it still.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Fixes: a814c359 ("firmware: dmi_scan: Check DMI structure length")
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>

This seems to cause flickering and lock-ups for a wide range of users.
Revert until we've found a proper fix for the flickering and lock-ups.

This reverts commit 36cc549d.

Cc: Shirish S <shirish.s@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit cd2d6c92.

Cc: Shirish S <shirish.s@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Hardware understands the regamma LUT as a piecewise linear function,
with points spaced exponentially along the range. We previously
programmed the LUT for range [2^-10, 2^0). This causes (normalized)
color values of 1 (=2^0) to miss the programmed LUT, and fall onto the
end region.

For DCE, the end region is extrapolated using a single (base, slope)
pair, using the max y-value from the last point in the curve as base.
This presents a problem, since this value affects all three color
channels. Scaling down the intensity of say - the blue regamma curve -
will not affect it's end region. This is especially noticiable when
using RedShift. It scales down the blue and green channels, but leaves
full-intensity colors unshifted.

Therefore, extend the range to cover [2^-10, 2^1) by programming another
hardware segment, containing only one point. That way, we won't be
hitting the end region.

Note that things are a bit different for DCN, since the end region can
be set per-channel.
Signed-off-by: NLeo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NRoman Li <roman.li@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.

The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.

The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted.  When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.

Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests.  As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.e>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Commit 42de82a8 previously attempted to fix this, and it did
correctly pad the MN and FR fields with spaces, but the SN field still
contains 0 bytes.  The current code fills out the first 16 bytes with
hex2bin, leaving the last 4 bytes zeroed.  Rather than adding a lot of
error-prone math to avoid overwriting SN twice, just set the whole thing
to spaces up front (it's only 20 bytes).

Fixes: 42de82a8 ("nvmet: don't report 0-bytes in serial number")
Signed-off-by: NDaniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: NMartin Wilck <mwilck@suse.com>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Also add error flow in case srcu initialization function fails.
Signed-off-by: NMax Gurtovoy <maxg@mellanox.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

We have to increment the number of logical blocks to a 1's based value
in the native format prior to converting to 512b units.
Signed-off-by: NRodrigo R. Galvao <rosattig@linux.vnet.ibm.com>
[changelog]
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The admin and first IO queues shared the first irq vector, which has an
affinity mask including cpu0. If a system allows cpu0 to be offlined,
the admin queue may not be usable if no other CPUs in the affinity mask
are online. This is a problem since unlike IO queues, there is only
one admin queue that always needs to be usable.

To fix, this patch allocates one pre_vector for the admin queue that
is assigned all CPUs, so will always be accessible. The IO queues are
assigned the remaining managed vectors.

In case a controller has only one interrupt vector available, the admin
and IO queues will share the pre_vector with all CPUs assigned.

Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMing Lei <ming.lei@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

All the queue memory is allocated up front. We don't take the node
into consideration when creating queues anymore, so removing the unused
parameter.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMing Lei <ming.lei@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

User reported controller always retains CSTS.RDY to 1, which fails
controller disabling when resetting the controller. This is also before
the admin queue is allocated, and trying to disable an unallocated queue
results in a NULL dereference.
Reported-by: NAlex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

nvmet_execute_get_disc_log_page() passes a fixed-length string into
nvmet_format_discovery_entry(), which then does a longer memcpy() on
it, as pointed out by gcc-8:

In function 'nvmet_format_discovery_entry',
    inlined from 'nvmet_execute_get_disc_log_page' at drivers/nvme/target/discovery.c:126:4:
drivers/nvme/target/discovery.c:62:2: error: 'memcpy' forming offset [38, 223] is out of the bounds [0, 37] [-Werror=array-bounds]
  memcpy(e->subnqn, subsys_nqn, NVMF_NQN_SIZE);

Using strncpy() will make this well-defined, filling the rest of the
buffer with zeroes, under the assumption that the input is either
a NUL-terminated string, or a byte sequence containing no zeroes.
If the input is a string that is longer than NVMF_NQN_SIZE, we
continue to have no NUL-termination in the output.

Fixes: a07b4970 ("nvmet: add a generic NVMe target")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

NVMe over Fabrics 1.0 Section 5.2 "Discovery Controller Properties and
Command Support" Figure 31 "Discovery Controller – Admin Commands"
explicitly listst all commands but "Get Log Page" and "Identify" as
reserved, but NetApp report the Linux host is sending Keep Alive
commands to the discovery controller, which is a violation of the
Spec.

We're already checking for discovery controllers when configuring the
keep alive timeout but when creating a discovery controller we're not
hard wiring the keep alive timeout to 0 and thus remain on
NVME_DEFAULT_KATO for the discovery controller.

This can be easily remproduced when issuing a direct connect to the
discovery susbsystem using:
'nvme connect [...] --nqn=nqn.2014-08.org.nvmexpress.discovery'
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Fixes: 07bfcd09 ("nvme-fabrics: add a generic NVMe over Fabrics library")
Reported-by: NMartin George <marting@netapp.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

nvme_start_keep_alive() isn't used outside core.c so unexport it and
make it static.
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

When nvmet_req_init() fails, __nvmet_req_complete() is called
to handle the target request via .queue_response(), so
nvme_loop_queue_response() shouldn't be called again for
handling the failure.

This patch fixes this case by the following way:

- move blk_mq_start_request() before nvmet_req_init(), so
nvme_loop_queue_response() may work well to complete this
host request

- don't call nvme_cleanup_cmd() which is done in nvme_loop_complete_rq()

- don't call nvme_loop_queue_response() which is done via
.queue_response()
Signed-off-by: NMing Lei <ming.lei@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
[trimmed changelog]
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Compiling on 32 bits system produces a warning for the shift width
when shifting 32 bit integer with 64bit integer.

Make sure that offset always is 64bit, and use macros for retrieving
lower and upper bits of the offset.
Signed-off-by: NMatias Bjørling <mb@lightnvm.io>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

The API docs describe i2c_transfer() as taking a pointer to an array
of i2c_msg containing at least 1 entry, but leaves it to the individual
drivers to sanity check the msgs and num parameters. Let's do this in
core code instead.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
[wsa: changed '<= 0' to '< 1']
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Tested-by: NJason Andryuk <jandryuk@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org

Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Fixes: 22e94bd6 ("i2c: i801: store and restore the SLVCMD register at load and unload")
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: NJason Andryuk <jandryuk@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org	# v4.10+

I added dumping of link information about tun devices over netlink in
commit 1ec010e7 ("tun: export flags, uid, gid, queue information
over netlink"), but didn't add the missing netlink notifications when
the device's exported properties change.

This patch adds notifications when owner/group or flags are modified,
when queues are attached/detached, and when a tun fd is closed.
Reported-by: NThomas Haller <thaller@redhat.com>
Fixes: 1ec010e7 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise, register_netdevice advertises the creation of the device with
the default flags, instead of what the user requested.
Reported-by: NThomas Haller <thaller@redhat.com>
Fixes: 1ec010e7 ("tun: export flags, uid, gid, queue information over netlink")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 92571a1a ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.

Fix this issue by removing the lan78xx_reset call from lan78xx_open.

Fixes: 92571a1a ("lan78xx: Connect phy early")
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.

If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi.  Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().

Fix it by checking for !bp->bnapi in bnxt_free_irq().

Fixes: e5811b8c ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings().  Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.

Fixes: fbcfc8e4 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:

	$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.

Fixes: f484f678 ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this patch the following commands would succeed as far as the
user was concerned:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01/44 action drop

The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed.  If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:

$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
	flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
	flower skip_sw src_mac 00:02:00:00:00:02 action drop
...

There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not.  Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.

Fixes: 2ae7408f ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding missing call to cache current backlight values.
Otherwise the brightness resets to default value on resume.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>