DIV_ROUND_UP is defined in linux/kernel.h only for the kernel.
When ethtool.h is included by a userland app, we got the following error:

include/linux/ethtool.h:1218:8: error: variably modified 'queue_mask' at file scope
  __u32 queue_mask[DIV_ROUND_UP(MAX_NUM_QUEUE, 32)];
        ^

Let's add a common definition in uapi and use it everywhere.

Fixes: ac2c7ad0 ("net/ethtool: introduce a new ioctl for per queue setting")
CC: Kan Liang <kan.liang@intel.com>
Suggested-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices declare a high number of TX queues, then set a much
lower real_num_tx_queues

This cause setups using fq_codel, sfq or fq as the default qdisc to consume
more memory than really needed.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch restructures the DMA bus settings and this is done
by introducing a new platform structure used for programming
the AXI Bus Mode Register inside the DMA module.
This structure can be populated from device-tree as documented in the
binding txt file.

After initializing the DMA, the AXI register can be optionally tuned
for platform drivers based.
This patch also reworks some parameters to make coherent the DMA
configuration now that AXI register is introduced.
For example, the burst_len is managed by using the mentioned axi
support above; so the snps,burst-len parameter has been removed.
It makes sense to provide the AAL parameter from DT to Address-Aligned
Beats inside the Register0 and review the PBL settings when initialize
the engine.

For PCI glue, rebuilding the story of this setting, it
was added to align a configuration so not for fixing some
known problem. No issue raised after this patch.
It is safe to use the default burst length instead of
tuning it to the maximum value
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 52bd2d62 ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.

Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).

Caller will now have to choose whether to map via
write-combining API or not.

mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.

Fixes: 88a85f99 ('TX latency optimization to save DMA reads')
Signed-off-by: NMoshe Lazer <moshel@mellanox.com>
Reviewed-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The command timeout is terribly long, whole two hours. Make it 60s so if
things do go wrong, the user gets feedback in relatively short time, so
they can take corrective actions and/or investigate using tools and such.

Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ICMP timestamp messages and IP source route options require
timestamps to be in milliseconds modulo 24 hours from
midnight UT format.

Add inet_current_timestamp() function to support this. The function
returns the required timestamp in network byte order.

Timestamp calculation is also changed to call ktime_get_real_ts64()
which uses struct timespec64. struct timespec64 is y2038 safe.
Previously it called getnstimeofday() which uses struct timespec.
struct timespec is not y2038 safe.
Signed-off-by: NDeepa Dinamani <deepa.kernel@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.

Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.

YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress

xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify

xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue

xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok

xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1  (rule hit 0 success 0)
  match 00000000/00000000 at 0 (success 0 )
        action order 1: ife decode action reclassify
         index 1 ref 1 bind 1 installed 14 sec used 14 sec
         type: 0x0
         Metadata: allow mark allow hash allow prio allow qmap
        Action statistics:
        Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
        backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules

YYYY: Lets show the sender side now ..

xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx:	ethertype 0xdead
xxx:	add skb->mark to whitelist of metadatum to send
xxx:	rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10  u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15

xxx: Lets show the encoding policy
sudo tc -s filter ls dev $ETH parent 1: protocol ip
xxx:
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2  (rule hit 0 success 0)
  match c0a87aed/ffffffff at 16 (success 0 )
  match 00010000/00ff0000 at 8 (success 0 )

	action order 1:  skbedit mark 17
	 index 6 ref 1 bind 1
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

	action order 2: ife encode action pipe
	 index 3 ref 1 bind 1
	 dst MAC: 02:15:15:15:15:15 type: 0xDEAD
 	 Metadata: allow mark
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0
xxx:

test by sending ping from sender to destination
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow for more multicast router port information to be dumped such as
timer and type attributes. For that that purpose we need to extend the
MDBA_ROUTER_PORT attribute similar to how it was done for the mdb entries
recently. The new format is thus:
[MDBA_ROUTER_PORT] = { <- nested attribute
    u32 ifindex <- router port ifindex for user-space compatibility
    [MDBA_ROUTER_PATTR attributes]
}
This way it remains compatible with older users (they'll simply retrieve
the u32 in the beginning) and new users can parse the remaining
attributes. It would also allow to add future extensions to the router
port without breaking compatibility.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for a temporary router port which doesn't depend only on the
incoming query. It can be refreshed if set to the same value, which is
a no-op for the rest.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using raw values makes it difficult to extend and also understand the
code, give them names and do explicit per-option manipulation in
br_multicast_set_port_router.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a user explicitly requests VLAN filtering with something like:

    # echo 1 > /sys/class/net/<bridge>/bridge/vlan_filtering

Switchdev propagates a SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING port
attribute.

Add support for it in the DSA layer with a new port_vlan_filtering
function to let drivers toggle 802.1Q filtering on user demand.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce devlink infrastructure for drivers to register and expose to
userspace via generic Netlink interface.

There are two basic objects defined:
devlink - one instance for every "parent device", for example switch ASIC
devlink port - one instance for every physical port of the device.

This initial portion implements basic get/dump of objects to userspace.
Also, port splitter and port type setting is implemented.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the initial implementation the only way to stop a rule from being
inserted into the hardware table was via the device feature flag.
However this doesn't work well when working on an end host system
where packets are expect to hit both the hardware and software
datapaths.

For example we can imagine a rule that will match an IP address and
increment a field. If we install this rule in both hardware and
software we may increment the field twice. To date we have only
added support for the drop action so we have been able to ignore
these cases. But as we extend the action support we will hit this
example plus more such cases. Arguably these are not even corner
cases in many working systems these cases will be common.

To avoid forcing the driver to always abort (i.e. the above example)
this patch adds a flag to add a rule in software only. A careful
user can use this flag to build software and hardware datapaths
that work together. One example we have found particularly useful
is to use hardware resources to set the skb->mark on the skb when
the match may be expensive to run in software but a mark lookup
in a hash table is cheap. The idea here is hardware can do in one
lookup what the u32 classifier may need to traverse multiple lists
and hash tables to compute. The flag is only passed down on inserts.
On deletion to avoid stale references in hardware we always try
to remove a rule if it exists.

The flags field is part of the classifier specific options. Although
it is tempting to lift this into the generic structure doing this
proves difficult do to how the tc netlink attributes are implemented
along with how the dump/change routines are called. There is also
precedence for putting seemingly generic pieces in the specific
classifier options such as TCA_U32_POLICE, TCA_U32_ACT, etc. So
although not ideal I've left FLAGS in the u32 options as well as it
simplifies the code greatly and user space has already learned how
to manage these bits ala 'tc' tool.

Another thing if trying to update a rule we require the flags to
be unchanged. This is to force user space, software u32 and
the hardware u32 to keep in sync. Thanks to Simon Horman for
catching this case.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.

This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The offload decision was originally very basic and tied to if the dev
implemented the appropriate ndo op hook. The next step is to allow
the user to more flexibly define if any paticular rule should be
offloaded or not. In order to have this logic in one function lift
the current check into a helper routine tc_should_offload().
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This method allows the controlling device (i.e. the bridge) to specify
additional headroom to be allocated for skb head on frame reception.
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the bottom qdisc decides to, for example, drop some packet,
it calls qdisc_tree_decrease_qlen() to update the queue length
for all its ancestors, we need to update the backlog too to
keep the stats on root qdisc accurate.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove nearly duplicated code and prepare for the following patch.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.

Relevant commands from his script:
    ip addr add 9.9.9.9/32 dev lo
    ip link set lo up

    ip link add name vrf0 type vrf table 101
    ip rule add oif vrf0 table 101
    ip rule add iif vrf0 table 101
    ip link set vrf0 up
    ip addr add 10.0.0.3/32 dev vrf0

    ip link add name dummy2 type dummy
    ip link set dummy2 master vrf0 up

    --> note dummy2 has no address - unnumbered device

    ip route add 10.2.2.2/32 dev dummy2 table 101
    ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02

    tcpdump -ni dummy2 &

And using ping instead of his socat example:
    $ ping -I vrf0 -c1 10.2.2.2
    ping: Warning: source address might be selected on device other than vrf0.
    PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64

Note the source address is from lo and is not a VRF local address. With
this patch:

    $ ping -I vrf0 -c1 10.2.2.2
    PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.

>From tcpdump:
    12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64

Now the source address comes from vrf0.

The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.

IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.

Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replaced by __ethtool_get_link_ksettings.
Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch defines a new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API,
handled by the new get_link_ksettings/set_link_ksettings callbacks.
This API provides support for most legacy ethtool_cmd fields, adds
support for larger link mode masks (up to 4064 bits, variable length),
and removes ethtool_cmd deprecated
fields (transceiver/maxrxpkt/maxtxpkt).

This API is deprecating the legacy ETHTOOL_GSET/SSET API and provides
the following backward compatibility properties:
 - legacy ethtool with legacy drivers: no change, still using the
   get_settings/set_settings callbacks.
 - legacy ethtool with new get/set_link_ksettings drivers: the new
   driver callbacks are used, data internally converted to legacy
   ethtool_cmd. ETHTOOL_GSET will return only the 1st 32b of each link
   mode mask. ETHTOOL_SSET will fail if user tries to set the
   ethtool_cmd deprecated fields to
   non-0 (transceiver/maxrxpkt/maxtxpkt). A kernel warning is logged if
   driver sets higher bits.
 - future ethtool with legacy drivers: no change, still using the
   get_settings/set_settings callbacks, internally converted to new data
   structure. Deprecated fields (transceiver/maxrxpkt/maxtxpkt) will be
   ignored and seen as 0 from user space. Note that that "future"
   ethtool tool will not allow changes to these deprecated fields.
 - future ethtool with new drivers: direct call to the new callbacks.

By "future" ethtool, what is meant is:
 - query: first try ETHTOOL_GLINKSETTINGS, and revert to ETHTOOL_GSET if
   fails
 - set: query first and remember which of ETHTOOL_GLINKSETTINGS or
   ETHTOOL_GSET was successful
   + if ETHTOOL_GLINKSETTINGS was successful, then change config with
     ETHTOOL_SLINKSETTINGS. A failure there is final (do not try
     ETHTOOL_SSET).
   + otherwise ETHTOOL_GSET was successful, change config with
     ETHTOOL_SSET. A failure there is final (do not try
     ETHTOOL_SLINKSETTINGS).

The interaction user/kernel via the new API requires a small
ETHTOOL_GLINKSETTINGS handshake first to agree on the length of the link
mode bitmaps. If kernel doesn't agree with user, it returns the bitmap
length it is expecting from user as a negative length (and cmd field is
0). When kernel and user agree, kernel returns valid info in all
fields (ie. link mode length > 0 and cmd is ETHTOOL_GLINKSETTINGS).

Data structure crossing user/kernel boundary is 32/64-bit
agnostic. Converted internally to a legal kernel bitmap.

The internal __ethtool_get_settings kernel helper will gradually be
replaced by __ethtool_get_link_ksettings by the time the first
"link_settings" drivers start to appear. So this patch doesn't change
it, it will be removed before it needs to be changed.
Signed-off-by: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the SO_CNX_ADVICE socket option (setsockopt only). The
purpose is to allow an application to give feedback to the kernel about
the quality of the network path for a connected socket. The value
argument indicates the type of quality report. For this initial patch
the only supported advice is a value of 1 which indicates "bad path,
please reroute"-- the action taken by the kernel is to call
dst_negative_advice which will attempt to choose a different ECMP route,
reset the TX hash for flow label and UDP source port in encapsulation,
etc.

This facility should be useful for connected UDP sockets where only the
application can provide any feedback about path quality. It could also
be useful for TCP applications that have additional knowledge about the
path outside of the normal TCP control loop.
Signed-off-by: NTom Herbert <tom@herbertland.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, all ipv6 addresses are flushed when the interface is configured
down, including global, static addresses:

    $ ip -6 addr show dev eth1
    3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
        inet6 2100:1::2/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
           valid_lft forever preferred_lft forever
    $ ip link set dev eth1 down
    $ ip -6 addr show dev eth1
    << nothing; all addresses have been flushed>>

Add a new sysctl to make this behavior optional. The new setting defaults to
flush all addresses to maintain backwards compatibility. When the set global
addresses with no expire times are not flushed on an admin down. The sysctl
is per-interface or system-wide for all interfaces

    $ sysctl -w net.ipv6.conf.eth1.keep_addr_on_down=1
or
    $ sysctl -w net.ipv6.conf.all.keep_addr_on_down=1

Will keep addresses on eth1 on an admin down.

    $ ip -6 addr show dev eth1
    3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
        inet6 2100:1::2/120 scope global
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
           valid_lft forever preferred_lft forever
    $ ip link set dev eth1 down
    $ ip -6 addr show dev eth1
    3: eth1: <BROADCAST,MULTICAST> mtu 1500 state DOWN qlen 1000
        inet6 2100:1::2/120 scope global tentative
           valid_lft forever preferred_lft forever
        inet6 fe80::e0:f9ff:fe79:34bd/64 scope link tentative
           valid_lft forever preferred_lft forever
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VLAN GetNext operation is specific to some switches, and thus can be
complicated to implement for some drivers.

Remove the support for the vlan_getnext/port_pvid_get approach in favor
of the generic and simpler port_vlan_dump function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to port_fdb_dump, add a port_vlan_dump function to DSA drivers
which gets passed the switchdev VLAN object and callback.

This function, if implemented, takes precedence over the soon legacy
vlan_getnext/port_pvid_get approach.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tc actions are stored in a per-module hashtable,
therefore are visible to all network namespaces. This is
probably the last part of the tc subsystem which is not
aware of netns now. This patch makes them per-netns,
several tc action API's need to be adjusted for this.

The tc action API code is ugly due to historical reasons,
we need to refactor that code in the future.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only release the memory of the hashtable itself, not its
entries inside. This is not a problem yet since we only call
it in module release path, and module is refcount'ed by
actions. This would be a problem after we move the per module
hinfo into per netns in the latter patch.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement set/get WOL by ethtool and added the needed
device commands and structures to mlx5_ifc.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NRana Shahout <ranas@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for DCBNL IEEE get/set max rate.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add access functions to set and query a physical port TC groups
and prio parameters.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add access functions to set and query a physical port PFC
(Priority Flow Control) parameters.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the device physical port access functions are implemented in the
port.c file.
We just extract the exposure of these functions from driver.h into a
dedicated header file called port.h.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No more users for it.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Helper for finding the type based on name. Useful if the
type needs to be determined based on device property.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
[modify rfkill_types array and BUILD_BUG_ON to not cause errors]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Today, the supplicant will add the RRM capabilities
Information Element in the association request only if
Quiet period is supported (NL80211_FEATURE_QUIET).

Quiet is one of many RRM features, and there are other RRM
features that are not related to Quiet (e.g. neighbor
report). Therefore, requiring Quiet to enable RRM is too
restrictive.
Some of the features, like neighbor report, can be
supported by user space without any help from the kernel.
Hence adding the RRM capabilities IE to association request
should be the sole user space's decision.
Removing the RRM dependency on Quiet in the driver solves
this problem, but using an old driver with a user space
tool that would not require Quiet feature would be
problematic: the user space would add NL80211_ATTR_USE_RRM
in the association request even if the kernel doesn't
advertize NL80211_FEATURE_QUIET and the association would
be denied by the kernel.

This solution adds a global RRM capability, that tells user
space that it can request RRM capabilities IE publishment
without any specific feature support in the kernel.
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>