When a vb2_queue is freed check if all the mem_ops and queue ops were balanced.
So the number of calls to e.g. buf_finish has to match the number of calls to
buf_prepare, etc.

This code is only enabled if CONFIG_VIDEO_ADV_DEBUG is set.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NPawel Osciak <pawel@osciak.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Fix an incorrect test in vb2_internal_qbuf() where only DEQUEUED buffers
are allowed. But PREPARED buffers are also OK.

Introduced by commit 4138111a
("vb2: simplify qbuf/prepare_buf by removing callback").
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Commit 88e26870 ("vb2: Improve file I/O
emulation to handle buffers in any order") broke read/write support if
the size of the buffer being read/written is less than the size of the
image.

When the commit was tested originally I used qv4l2, which calls read()
with exactly the size of the image. But if you try 'cat /dev/video0'
then it will fail and typically hang after reading two buffers.

This patch fixes the behavior by adding a new cur_index field that
contains the index of the field currently being filled/read, or it
is num_buffers in which case a new buffer needs to be dequeued.

The old index field has been renamed to initial_index in order to be
a bit more descriptive.

This has been tested with both read and write.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch adds a test preventing streamon() if there is no buffer
ready.

Without this patch, a user could call streamon() before
preparing any buffer. This leads to a situation where if he calls
close() before calling streamoff() the device is kept streaming.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Linux 3.14-rc5

* tag 'v3.14-rc5': (1117 commits)
  Linux 3.14-rc5
  drm/vmwgfx: avoid null pointer dereference at failure paths
  drm/vmwgfx: Make sure backing mobs are cleared when allocated. Update driver date.
  drm/vmwgfx: Remove some unused surface formats
  MAINTAINERS: add maintainer entry for Armada DRM driver
  arm64: Fix !CONFIG_SMP kernel build
  arm64: mm: Add double logical invert to pte accessors
  dm cache: fix truncation bug when mapping I/O to >2TB fast device
  perf tools: Fix strict alias issue for find_first_bit
  powerpc/powernv: Fix indirect XSCOM unmangling
  powerpc/powernv: Fix opal_xscom_{read,write} prototype
  powerpc/powernv: Refactor PHB diag-data dump
  powerpc/powernv: Dump PHB diag-data immediately
  powerpc: Increase stack redzone for 64-bit userspace to 512 bytes
  powerpc/ftrace: bugfix for test_24bit_addr
  powerpc/crashdump : Fix page frame number check in copy_oldmem_page
  powerpc/le: Ensure that the 'stop-self' RTAS token is handled correctly
  kvm, vmx: Really fix lazy FPU on nested guest
  perf tools: fix BFD detection on opensuse
  drm/radeon: enable speaker allocation setup on dce3.2
  ...

Use the correct name in the comment describing function
omap3isp_module_sync_is_stopping().

isp_isr() never returned IRQ_NONE, remove the comment saying so.
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch renames the variable in the description to match it
appropriately to function definition.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This patch removes the description of members which does not exists for
ispccdc_lsc structure.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add bayer 8-bit GUIDs to uvcvideo and associated them with the
corresponding V4L2 pixel formats.
Signed-off-by: NEdgar Thier <info@edgarthier.net>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The UVC specification uses alternate setting selection to notify devices
of stream start/stop. This breaks when using bulk-based devices, as the
video streaming interface has a single alternate setting in that case,
making video stream start and video stream stop events to appear
identical to the device. Bulk-based devices are thus not well supported
by UVC.

The webcam built in the Asus Zenbook UX302LA ignores the set interface
request and will keep the video stream enabled when the driver tries to
stop it. If USB autosuspend is enabled the device will then be suspended
and will crash, requiring a cold reboot.

USB trace capture showed that Windows sends a CLEAR_FEATURE(HALT)
request to the bulk endpoint when stopping the stream instead of
selecting alternate setting 0. The camera then behaves correctly, and
thus seems to require that behaviour.

Replace selection of alternate setting 0 with clearing of the endpoint
halt feature at video stream stop for bulk-based devices. Let's refrain
from blaming Microsoft this time, as it's not clear whether this
Windows-specific but USB-compliant behaviour was specifically developed
to handle bulkd-based UVC devices, or if the camera just took advantage
of it.

CC: stable@vger.kernel.org
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Timestamp buffer flags are constant at the moment. Document them so that 1)
they're always valid and 2) not changed by the drivers. This leaves room to
extend the functionality later on if needed.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Copy the flags containing the timestamp source from source buffer flags to
the destination buffer flags on memory-to-memory devices. This is analogous
to copying the timestamp field from source to destination.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The timestamp and timecode fields were copied from destination to source,
not the other way around as they should. Fix it.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The UVC device provided timestamps are taken from the clock once the
exposure of the frame has begun, not when the reception of the frame would
have been finished as almost anywhere else. Show this to the user space by
using V4L2_BUF_FLAG_TSTAMP_SRC_SOE buffer flag.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

For COPY timestamps, buffer timestamp source flags will traverse the queue
untouched.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some devices do not produce timestamps that correspond to the end of the
frame. The user space should be informed on the matter. This patch achieves
that by adding buffer flags (and a mask) for timestamp sources since more
possible timestamping points are expected than just two.

A three-bit mask is defined (V4L2_BUF_FLAG_TSTAMP_SRC_MASK) and two of the
eight possible values is are defined V4L2_BUF_FLAG_TSTAMP_SRC_EOF for end of
frame (value zero) V4L2_BUF_FLAG_TSTAMP_SRC_SOE for start of exposure (next
value).
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NKamil Debski <k.debski@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Mask out other bits when comparing timestamp types.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The timestamp_type field used to contain only the timestamp type. Soon it
will be used for timestamp source flags as well. Rename the field
accordingly.

[m.chehab@samsung.com: do the change also to drivers/staging/media and at s2255]
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The buffer flags field is 32 bits but the defined only used 16. This is
fine, but as more than 16 bits will be used in the very near future, define
them as 32-bit numbers for consistency.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Document that monotonic timestamps are taken after the corresponding frame
has been received, not when the reception has begun. This corresponds to the
reality of current drivers: the timestamp is naturally taken when the
hardware triggers an interrupt to tell the driver to handle the received
frame.

Remove the note on timestamp accuracy as it is fairly subjective what is
actually an unstable timestamp.

Also remove explanation that output buffer timestamps can be used to delay
outputting a frame.

Remove the footnote saying we always use realtime clock.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

When sending a buffer to a video output device some of the fields need
to be copied so they arrive in the driver. These are the KEY/P/BFRAME
flags and the TIMECODE flag, and, if that flag is set, the timecode field
itself.

There are a number of functions involved in this: the __fill_vb2_buffer()
is called while preparing a buffer. For output buffers the buffer contains
the video data, so any meta data associated with that (KEY/P/BFRAME and
the field information) should be stored at that point.

The timecode, timecode flag and timestamp information is not part of that,
that information will have to be set when vb2_internal_qbuf() is called to
actually queue the buffer to the driver. Usually VIDIOC_QBUF will do the
prepare as well, but you can call PREPARE_BUF first and only later VIDIOC_QBUF.
You most likely will want to set the timestamp and timecode when you actually
queue the buffer, not when you prepare it.

Finally, in buf_prepare() make sure the timestamp and sequence fields are
actually cleared so that when you do a QUERYBUF of a prepared-but-not-yet-queued
buffer you will not see stale timestamp/sequence data.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Modern silicon RF tuners used nowadays has many controllable gain
stages on signal path. Usually, but not always, there is at least
3 gain stages. Also on some cases there could be multiple gain
stages within the ones specified here. However, I think that having
these three controllable gain stages offers enough fine-tuning for
real use cases.

1) LNA gain. That is first gain just after antenna input.
2) Mixer gain. It is located quite middle of the signal path, where
RF signal is down-converted to IF/BB.
3) IF gain. That is last gain in order to adjust output signal level
to optimal level for receiving party (usually demodulator ADC).

Each gain stage could be set rather often both manual or automatic
(AGC) mode. Due to that add separate controls for controlling
operation mode.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add documentation for LNA, mixer and IF gain controls. These
controls are RF tuner specific.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

It is class for RF tuner specific controls, like gain controls,
filters, signal strength.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Delay possible I2C gate close a little bit in order to see if there
is next message coming to tuner in a sequence.

Also, export private muxed I2C adapter. That is aimed only for SDR
extension module as SDR belongs to same RTL2832 physical I2C bus (it
is physically property of RTL2832, whilst it is own kernel module).
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: NLuis Alves <ljalvs@gmail.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There was a deadlock between master I2C adapter and muxed I2C
adapter. Implement two I2C muxed I2C adapters and leave master
alone, just only for offering I2C adapter for these mux adapters.
Reported-by: NLuis Alves <ljalvs@gmail.com>
Reported-by: NBenjamin Larsson <benjamin@southpole.se>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

RTL2832 provides gated / repeater I2C adapter for tuner.
Implement it as a muxed I2C adapter.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Most of those were reported by checkpatch.pl...

debug module parameter is not used anywhere so remove it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Disable IR interrupts in order to avoid SDR sample loss.
IR interrupts causes some extra load for device and it seems
be one reason to loss samples when sampling rate is high.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

There is now new tuner types which are not handled on that switch-case.
Print error if unknown tuner type is meet.

drivers/media/tuners/tuner-xc2028.c: In function ‘generic_set_freq’:
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_ADC’ not handled in switch [-Wswitch]
  switch (new_type) {
  ^
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_RF’ not handled in switch [-Wswitch]

Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Some previous patch introduced this bug:

/devel/v4l/patchwork/Documentation/DocBook/controls.xml:2262: parser error : attributes construct error
	      <row id=""v4l2-mpeg-video-hor-search-range">
	                ^
/devel/v4l/patchwork/Documentation/DocBook/controls.xml:2262: parser error : Couldn't find end of Start Tag row line 2262
	      <row id=""v4l2-mpeg-video-hor-search-range">
	                ^
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add SDR to V3.15 revlist, and add the credits to Antti.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add SDR device type to v4l2-framework.txt document.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Let it be experimental still as all SDR drivers are in staging.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Document V4L2 SDR interface.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Update documentation to reflect 1 Hz frequency step flag.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Modulator ioctls could be enabled mistakenly for non-radio devices.
Currently those ioctls are only valid for radio. Fix it.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>