We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address.  However, swiotlb maps in units of
2K, breaking this assumption.

Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed.  We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent.  (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Delete successive tests to the same location.  rc was previously tested and
not subsequently updated.  efx_phc_adjtime can return an error code, so the
call is updated so that is tested instead.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@

*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
    when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers.  This patch fixes all of
them back up to be properly aligned.

Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Most of the module parameters treated as boolean are currently exposed
as type int or uint.  Defining them with the proper type is useful
documentation for both users and developers.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_mcdi_poll() uses get_seconds() to read the current time and to
implement a polling timeout.  The use of this function was chosen
partly because it could easily be replaced in a co-sim environment
with a macro that read the simulated time.

Unfortunately the real get_seconds() returns the system time (real
time) which is subject to adjustment by e.g. ntpd.  If the system time
is adjusted forward during a polled MCDI operation, the effective
timeout can be shorter than the intended 10 seconds, resulting in a
spurious failure.  It is also possible for a backward adjustment to
delay detection of a areal failure.

Use jiffies instead, and change MCDI_RPC_TIMEOUT to be denominated in
jiffies.  Also correct rounding of the timeout: check time > finish
(or rather time_after(time, finish)) and not time >= finish.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The assertion of netif_device_present() at the top of
efx_hard_start_xmit() may fail if we don't do this.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

We sometimes hit a "failed to flush" timeout on some TX queues, but the
flushes have completed and the flush completion events seem to go missing.
In this case, we can check the TX_DESC_PTR_TBL register and drain the
queues if the flushes had finished.

[bwh: Minor fixes to coding style]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

If the MC reboots then the stats it reports to us will have been
reset.  We need to reset ours to get efx_update_diff_stat() working
properly.

(Ideally we would maintain stats across the reboot, but as this should
only happen immediately after a firmware upgrade it's not really worth
the trouble.)
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Currently we initialise the newly allocated buffer to all-1s, which is
important for event queues but not for descriptor queues.  And since
we also do that in efx_nic_init_eventq(), it is completely pointless
to do it here.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_writed_table() uses a step of 16 bytes but efx_readd_table() uses
a step of 4 bytes.  Why are they different?

Firstly, register access is asymmetric:

- The EVQ_RPTR table and RX_INDIRECTION_TBL can (or must?) be written
  as dwords even though they have a step size of 16 bytes, unlike
  most other CSRs.
- In general, a read of any width is valid for registers, so long as
  it does not cross register boundaries.  There is also no latching
  behaviour in the BIU, contrary to rumour.

We write to the EVQ_RPTR table with efx_writed_table() but never read
it back as it's write-only.  We write to the RX_INDIRECTION_TBL with
efx_writed_table(), but only read it back for the register dump, where
we use efx_reado_table() as for any other table with step size of 16.

We read MC_TREG_SMEM with efx_readd_table() for the register dump, but
normally read and write it with efx_readd() and efx_writed() using
offsets calculated in bytes.

Since these functions are trivial and have few callers, it's clearer
to open-code them at the call sites.  While we're at it, update the
comments on the BIU behaviour again.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_mcdi_rpc_start() returns a negative value on error or zero on
success.  However one caller that can't properly handle failure then
does WARN_ON(rc > 0).  Change it to WARN_ON(rc < 0).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Receiving pause frames can block TX queue flushes.  Earlier changes
work around this by reconfiguring the MAC during flushes for VFs, but
during flushes for the PF we would only change the fc_disable counter.
Unless the MAC is reconfigured for some other reason during the flush
(which I would not expect to happen) this had no effect at all.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Add necessary cast when setting a bogus checksum.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

sparse has got a bit more picky since I last ran it over this.  Add
forced casts for use of ~0 as a big-endian value.  Undo the pointless
optimisation of parameter validation with '|'; using '||' avoids these
warnings.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Various drivers depend on INET because they used to select INET_LRO,
but they have all been converted to use GRO which has no such
dependency.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was missed in commit a24006ed
('ptp: Enable clock drivers along with associated net/PHY drivers')
which enabled sfc's clock driver unconditionally.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:

- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
  as part of net driver modules.  (This also fixes cases where the PTP
  subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
  drivers but are built separately
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using list_move() instead of list_del() + list_add().

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are now standard functions for dealing with little-endian bit
arrays, so use them instead of our own implementations.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Each RX filter table contains filters with two different levels of
specificity: TCP/IPv4 and UDP/IPv4 filters match the local address and
port and optionally the remote address and port; Ethernet filters
match the local address and optionally the VID.  The more specific
filters always override less specific filters within the same table,
and should be numbered accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

This filter flag cannot yet be set through the ethtool command and
will not be supported on future hardware.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The loopback self-test iterates over all the TX queues of channel 0,
which is not very interesting when that's an RX-only channel.
Signed-off-by: NBen Hutchings <bhutchings@solarflre.com>

The least significant bit number (LBN) of a field within an MCDI
structure is counted from the start of the structure, not the
containing dword.  In MCDI_ARRAY_FIELD() we need to mask it rather
than using the usual EFX_DWORD_FIELD() macro.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Commit c31e5f9f ('sfc: Add channel specific receive_skb handler and
post_remove callback') added the function pointer field
efx_channel_type::post_remove and an unconditional call through it.

This field should have been initialised to efx_channel_dummy_op_void
in the existing instances of efx_channel_type, but this was only done
in efx_default_channel_type.  Consequently, if a device has SR-IOV
enabled then removing the driver or device will result in an oops.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MCDI supports requests up to 252 bytes long, which is only enough to
pass 63 RX queue IDs to MC_CMD_FLUSH_RX_QUEUES.  However a VF may have
up to 64 RX queues, and if we try to flush them all we will generate
an over-length request and BUG() in efx_mcdi_copyin().  Currently
all VF drivers limit themselves to 32 RX queues, so reducing the
limit to 63 does no harm.

Also add a BUILD_BUG_ON in efx_mcdi_flush_rxqs() so we remember to
deal with the same problem there if EFX_MAX_CHANNELS is increased.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The key new feature for 3.2 is PTP support.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

On big-endian systems the MTD partition names currently have mangled
subtype numbers and are not recognised by the firmware update tool
(sfupdate).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Add PTP IEEE-1588 support and make accesible via the PHC subsystem.

This work is based on prior code by Andrew Jackson
Signed-off-by: NStuart Hodgson <smhodgson@solarflare.com>
[bwh:
 - Add byte order conversion in efx_ptp_send_times()
 - Simplify conversion of PPS event times
 - Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The maximum array sizes have been calculated on the basis of a maximum
SDU size of 255 bytes, whereas the actual maximum is 252 bytes.
Constructing a larger SDU will result in a BUG_ON in efx_mcdi_copyin.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

For NIC/System time synchonisation efx_mcdi_rpc needs to be split in
efx_mcdi_rpc_start and efx_mcdi_rpc_finish operations.
Signed-off-by: NStuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Allows an extra channel to override the standard receive_skb handler
and also for extra non generic operations to be performed on remove.

Also set default rx strategy so only skbs can be delivered to the
PTP receive function.
Signed-off-by: NStuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

The PTP channel will have its own RX queue even though it's not
a regular traffic channel.

Original work by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NStuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>