Add a pin control driver for the TZ1090's low power pins via the
powerdown controller SOC_GPIO_CONTROL registers.

These pins have individually controlled pull-up, and group controlled
schmitt, slew-rate, drive-strength, and power-on-start (pos).

The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the
ir_mod_stable_out and ir_mod_power_out functions respectively. If no
function is set they remain in GPIO mode. These muxes can be overridden
by requesting them as GPIOs.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add a pin control driver for the main pins on the TZ1090 SoC. This
doesn't include the low-power pins as they're controlled separately via
the Powerdown Controller (PDC) registers.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'drvdata_list' is used only in this file. Make it static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

At several places, return value was not tested
and error output was missing.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Replace hardcoded value by corresponding #define's.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Factorize code by adding abx500_pullud_supported()
which improve code readability.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

- allow to get output GPIO value
- as there is no GPIO0 on ABX500, use correct offset with
  abx500_gpio_get_bit()
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

- Update abx500_pin_config_set() in order to take in
account PIN_CONFIG_BIAS_DISABLE state to disable
pull up or pull down.

- Rework error path.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We use the same way to define pin muxing and pin configuration
than for nomadik. So pickup code from pinctrl_nomadik.c to be
able to implement pin multiplexing and pin configuration using
the device tree. Pin configuration uses generic parsing code.
Signed-off-by: NGabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fix a compilation error caused by pinconf_generic_parse_dt_config() not
being defined on !CONFIG_OF platforms by guarding the whole DT node
parsing code with #ifdef CONFIG_OF.

Defining a pinconf_generic_parse_dt_config() on !CONFIG_OF would have
been possible as well, but would have resulted in a larger code size on
!CONFIG_OF platforms (such as arch/sh).
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for gpio on Intel BayTrail platforms. BayTrail supports 3 banks
of gpios called SCORE, NCORE ans SUS with 102, 28 and 44 gpio pins.
Supports gpio interrupts and ACPI gpio events

Pins may be muxed to alternate function instead of gpio by firmware.
This driver does not touch the pin muxing and expect firmare
to set pin muxing and pullup/down properties properly.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Symbols referenced only in this file are made static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'spear310_o2p' is referenced only in this file.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some symbols referenced only in this file are made static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'bcm2835_gpio_pins' is used only in this file.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Support device instantiation through the device tree. The compatible
property is used to select the SoC pinmux information.

Set the gpio_chip device field to the PFC device to enable automatic
GPIO OF support.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Platform data isn't used, support can thus be removed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the missing unlock before return from function pinctrl_find_gpio_range_from_pin()
in the error handling case.

Introduced by commit 2ff3477efd7086544b9e298fc63afab0645921b4.
(pinctrl: add pin list based GPIO ranges)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

A level-triggered interrupt should be acked after the interrupt line
becomes inactive and before it is unmasked, or else another interrupt
will be immediately triggered.  Acking before or after calling the
handler is not enough.
Signed-off-by: NLuigi Semenzato <semenzato@chromium.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The three functions pinctrl_pm_select_default_state,
pinctrl_pm_select_sleep_state, and pinctrl_pm_select_idle_state
are used in drivers that can be loadable modules, and should
be exported.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Change the rockchip pinctrl driver to handle the arguments to the pull
pinconfig options correctly. So only accept non-0 values for the
pull options as the rockchip pin-controller can only turn pulls on and
off (this via BIAS_DISABLE).
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Make pinctrl-single able to handle suspend/resume events and change
hogged pins states accordingly.
Signed-off-by: NHebbar Gururaja <gururaja.hebbar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It will allow us to have a cleaner separation between the data needed by
the driver to work, and the core logic of the driver in itself, and will
allow having too much noise in the core driver in the future.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Allocating the temorary array in pinconf_generic_parse_dt_config on stack
might cause problems later on, when the number of options grows over time.
Therefore also allocate this array dynamically to be on the safe side.
Suggested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a shortcut when no valid pinconf properties are found
in the parsed dt node, to set the values immediately and return.
Suggested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The bias-pull-* options use values > 0 to indicate that the pull should
be activated and optionally also indicate the strength of the pull.
Therefore use an default value of 1 for these options.

Split the low-power-mode option into low-power-enable and -disable.

Update the documentation to describe the param arguments better.
Reported-by: NJames Hogan <james.hogan@imgtec.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Traditionally, GPIO ranges are based on consecutive ranges of both GPIO
and pin numbers. This patch allows for GPIO ranges with arbitrary lists
of pin numbers.
Signed-off-by: NChristian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch does nothing but reorder the functions to improve the
readability of a future patch.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The patch:
  19846950 pinctrl: samsung: Protect bank registers with a spinlock

...added spinlocks to protect many accesses.  However, the irq_mask
and irq_unmask functions still do an unprotected read/modify/write.
Add the spinlock there.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

pinctrl-abx500.c: In function 'abx500_gpio_dbg_show_one':
pinctrl-abx500.c:534:14: warning: 'pud' may be used
uninitialized in this function [-Wuninitialized]
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver adds support the Cortex-A9 based SoCs from Rockchip,
so at least the RK2928, RK3066 (a and b) and RK3188.
Earlier Rockchip SoCs seem to use similar mechanics for gpio
handling so should be supportable with relative small changes.
Pull handling on the rk3188 is currently a stub, due to it being
a bit different to the earlier SoCs.

Pinmuxing as well as gpio (and interrupt-) handling tested on
a rk3066a based machine.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

pinconf_generic_parse_dt_config() takes a node as input and generates an
array of generic pinconfig values from the properties of this node.

As I couldn't find a mechanism to count the number of properties of a node
the function uses internally an array to accept one of parameter and copies
the real present options to a smaller variable at its end.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The A10 and A13 has a few pins that can be muxed into a particular
function that can be used as an interrupt source. Add the available
pins for such functions to the A10 and A13 description array.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The port controller IP found in the Allwinner A10 and A13 can use few of
the pins it manage as an interrupt source, called external interrupts in
the datasheet.

The number of these external interrupts are SoCs specific, but the
current upper limit is 32. In order to work, the external interrupts'
pins have to be muxed to a specific function to generate an interrupt.

This patch adds the irqchip and the needed logic to use the PIO
controller as an interrupt controller.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Avoid to use expensive string manipulation functions and search by pin
id when possible.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch fixes issues reported by prevent tool.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
[Drop hunk already in-tree from a patch by Wei Yongjun]
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Take care to name pin names as
register-offset.bit-pos-of-pin-in-register in case configuring multiple
pins in register.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>