Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards.  Original timing data is from the Micron
datasheet PDF downloaded from:

http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf

Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Gumstix will soon be shipping a variant of their Summit board that
includes an SMSC LAN9221 ethernet interface.  This patch provides
support via the smsc911x driver when enabled in kernel config.

The Overo defconfig is not updated since the LAN9221 is an option
not present on all systems.
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>

Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

An upcoming Overo expansion board includes an ADS7846 touchscreen controller.

This patch adds support via the ads7846 driver when enabled in the
kernel config.
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Create a generic board-file for initializing usb
on omap2430 and omap3 boards.

Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Correct twl4030 MMC power switching:  fix voltage ranges reported
for each slot, and handle them fully.

 Lies corrected:
  - MMC-1 doesn't support the 2.6-2.7 Volt range
  - MMC-2 can't normally support anything except 1.8V
 Omissions corrected
  - MMC-1 *does* handle the 2.8-2.9 Volt range
  - MMC-2 can handle 2.5-3.2 Volt cards, given a transceiver

Add transciever support for MMC-2; enable it for Overo and Pandora.
(Depends on something else to have set up pinmuxing for control
signals instead of as MMC2_DAT4..7 pins.)

Also shrink twl4030_hsmmc_info a smidgeon ... padding is all gone.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move the defines to the associated board file and remove
the now unnecessary header file.
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.

Also change wire4 to be wires, as some newer controllers support
8 data lines.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds minimal overo support.
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>