Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is not needed, the comment there was wrong, it
is only needed when MSI was *not* enabled.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The allocation failure will already be very verbose.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a firmware error occurs, don't just abort synchronous
commands but also return an error (-EIO) and block any new
commands as well. Currently, an error is only returned if
WANT_SKB was set which is confusing and can lead to issues.

Blocking is done until a new firmware image is loaded.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The printk message should say RX, not TX.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to print the PCI resource
length and base address, nor the hardware
revision ID (which can be found in lspci)
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no reason to print these all the time,
the messages aren't all that interesting. Leave
them as DEBUG_INFO though, just in case.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the EEPROM reading was successful, don't print
a message by default, the EEPROM version isn't all
that interesting. Change the message to DEBUG_INFO
priority so it can still be obtained.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

People tend not to set the fields they want to leave as 0.
So make sure the struct is zeroed properly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The ALIVE response of new fw inclues the base address of
the SCD in SRAM. Until we read it from a prph register,
which was set by the fw. Since the fw might well stop
updating the prph register, add a WARN when there is an
inconsitency between the ALIVE response and the register
to catch any change in the behavior.
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of open-coding it with a temporary list_head
pointer, just use list_first_entry.
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The flush_control parameter to iwlagn_txfifo_flush
is passed as an internal value (context flags) and
then sent to the device, that can't be right.

Fix the confusion by removing the parameter, always
use IWL_DROP_ALL that is redefined according to the
firmware API in the flush control.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no reason to clear the CTL_AMPDU flag on
transmitted frame status, it's not used by the
driver here and mac80211 only uses it for some
rate statistics.

Also remove a stray space in the function.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The flush command really flushes queues, not
FIFOs, and the first 32 bits indicate the
queues to flush, not FIFOs. Change the command
accordingly.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we unregister from mac80211 it will down the device anyway.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

No HCMD can be sent while RFKILL is asserted. If a SYNC
command is running while RFKILL is asserted the fw will
silently discard it. This means that the driver needs to
wake the process that sleeps on the CMD_SYNC.

Since the RFKILL interrupt is handled in the transport layer
and the code that sleeps in CMD_SYNC is also in the transport
layer, all this logic can be handled there.
This simplifies the work of the op_mode.

So the transport layer will now return -ERFKILL when a CMD
is sent and RFKILL is asserted. This will be the case even
when the CMD is SYNC. The transport layer will return
-ERFKILL straight away.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clarify the documentation to indicate that these
flags can only be used at the end, i.e. after them
a copy TFD (no flags set) is invalid.
Reported-by: NInbal Hacohen <inbal.hacohen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In addition to the NOCOPY flag, add a DUP flag that
tells the transport to kmemdup() the buffer and free
it after the command completes.

Currently this is only supported for a single buffer
in a given command, but that could be extended if it
should be needed.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove the Kconfig option CONFIG_IWLWIFI_EXPERIMENTAL_MFP,
if the firmware doesn't support MFP then the user shouldn't
have the option to enable it as it won't work correctly.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since the queue might not be empty, we need to free the
pending Tx packets.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This can happen when we shut down suddenly an interface.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Once in bus enumeration is enough, no need to print it
again when the op_mode loads.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Doing the opposite is wrong, the SCD wouldn't like someone
to clear its data while the queue is still active.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of hardcoding the expression, use the macro
provided in the previous patch.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When we disable a queue, we don't want the SCD to remember anything
about this queue (what packet was transmitted but not acked, what
packed was acked etc...).
Wipe out all this data in its SRAM.

Constify the arguments to iwl_write_targ_mem_dwords on the way.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove a number of variables that are assigned, but not used.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When tracing in iwlwifi, we get all data. Most of
the time, we don't need it, and it just takes up
a lot of extra space in the trace.

Make this optional by recording the data into two
separate trace events if it is needed. Without it,
record only the content of non-data and EAPOL TX
frames.

As a result, tracing without the data tracepoints
will record meta information including the 802.11
headers for all frames but will not record the
contents of data frames to reduce trace overhead.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When warning about a command that is too large,
print out the command name/ID to help figure
out which place is attempting to send a command
that is too large.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull MIPS update from Ralf Baechle:
 "Cleanups and fixes for breakage that occured earlier during this merge
  phase.  Also a few patches that didn't make the first pull request.
  Of those is the Alchemy work that merges code for many of the SOCs and
  evaluation boards thus among other code shrinkage, reduces the number
  of MIPS defconfigs by 5."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
  MIPS: SNI: Switch RM400 serial to SCCNXP driver
  MIPS: Remove unused empty_bad_pmd_table[] declaration.
  MIPS: MT: Remove kspd.
  MIPS: Malta: Fix section mismatch.
  MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
  MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
  MIPS: Alchemy: merge PB1550 support into DB1550 code
  MIPS: Alchemy: Single kernel for DB1200/1300/1550
  MIPS: Optimize TLB refill for RI/XI configurations.
  MIPS: proc: Cleanup printing of ASEs.
  MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
  MIPS: Add detection of DSP ASE Revision 2.
  MIPS: Optimize pgd_init and pmd_init
  MIPS: perf: Add perf functionality for BMIPS5000
  MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
  MIPS: perf: Remove unnecessary #ifdef
  MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
  MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
  MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
  vmlinux.lds.h: Allow architectures to add sections to the front of .bss
  ...

Pull module signing support from Rusty Russell:
 "module signing is the highlight, but it's an all-over David Howells frenzy..."

Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.

* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
  X.509: Fix indefinite length element skip error handling
  X.509: Convert some printk calls to pr_devel
  asymmetric keys: fix printk format warning
  MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
  MODSIGN: Make mrproper should remove generated files.
  MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
  MODSIGN: Use the same digest for the autogen key sig as for the module sig
  MODSIGN: Sign modules during the build process
  MODSIGN: Provide a script for generating a key ID from an X.509 cert
  MODSIGN: Implement module signature checking
  MODSIGN: Provide module signing public keys to the kernel
  MODSIGN: Automatically generate module signing keys if missing
  MODSIGN: Provide Kconfig options
  MODSIGN: Provide gitignore and make clean rules for extra files
  MODSIGN: Add FIPS policy
  module: signature checking hook
  X.509: Add a crypto key parser for binary (DER) X.509 certificates
  MPILIB: Provide a function to read raw data into an MPI
  X.509: Add an ASN.1 decoder
  X.509: Add simple ASN.1 grammar compiler
  ...

The hostprogs need access to the CONFIG_* symbols found in
include/generated/autoconf.h.  But commit abbf1590 ("UAPI: Partition
the header include path sets and add uapi/ header directories") replaced
$(LINUXINCLUDE) with $(USERINCLUDE) which doesn't contain the necessary
include paths.

This has the undesirable effect of breaking the EFI boot stub because
the #ifdef CONFIG_EFI_STUB code in arch/x86/boot/tools/build.c is
never compiled.

It should also be noted that because $(USERINCLUDE) isn't exported by
the top-level Makefile it's actually empty in arch/x86/boot/Makefile.

Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The UAPI commits forgot to test tooling builds such as tools/perf/,
and this fixes the fallout.

Manual conversion.
Signed-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ARM update from Russell King:
 "This is the final round of stuff for ARM, left until the end of the
  merge window to reduce the number of conflicts.  This set contains the
  ARM part of David Howells UAPI changes, and a fix to the ordering of
  'select' statements in ARM Kconfig files (see the appropriate commit
  for why this happened - thanks to Andrew Morton for pointing out the
  problem.)

  I've left this as long as I dare for this window to avoid conflicts,
  and I regenerated the config patch yesterday, posting it to our
  mailing list for review and testing.  I have several acks which
  include successful test reports for it.

  However, today I notice we've got new conflicts with previously unseen
  code...  though that conflict should be trivial (it's my changes vs a
  one liner.)"

* 'late-for-linus' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: config: make sure that platforms are ordered by option string
  ARM: config: sort select statements alphanumerically
  UAPI: (Scripted) Disintegrate arch/arm/include/asm

Fix up fairly conflict in arch/arm/Kconfig (the select re-organization
vs recent addition of GENERIC_KERNEL_EXECVE)

Pull UAPI disintegration for include/linux/{,byteorder/}*.h from David Howells:
 "The patches contained herein do the following:

 (1) Remove kernel-only stuff in linux/ppp-comp.h from the UAPI.  I checked
     this with Paul Mackerras before I created the patch and he suggested some
     extra bits to unexport.

 (2) Remove linux/blk_types.h entirely from the UAPI as none of it is userspace
     applicable, and remove from the UAPI that part of linux/fs.h that was the
     reason for linux/blk_types.h being exported in the first place.  I
     discussed this with Jens Axboe before creating the patch.

 (3) The big patch of the series to disintegrate include/linux/*.h as a unit.
     This could be split up, though there would be collisions in moving stuff
     between the two Kbuild files when the parts are merged as that file is
     sorted alphabetically rather than being grouped by subsystem.

     Of this set of headers, 17 files have changed in the UAPI exported region
     since the 4th and only 8 since the 9th so there isn't much change in this
     area - as one might expect.

     It should be pretty obvious and straightforward if it does come to fixing
     up: stuff in __KERNEL__ guards stays where it is and stuff outside moves
     to the same file in the include/uapi/linux/ directory.

     If a new file appears then things get a bit more complicated as the
     "headers +=" line has to move to include/uapi/linux/Kbuild.  Only one new
     file has appeared since the 9th and I judge this type of event relatively
     unlikely.

 (4) A patch to disintegrate include/linux/byteorder/*.h as a unit.

  Signed-off-by: David Howells <dhowells@redhat.com>"

* tag 'disintegrate-main-20121013' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/linux/byteorder
  UAPI: (Scripted) Disintegrate include/linux
  UAPI: Unexport linux/blk_types.h
  UAPI: Unexport part of linux/ppp-comp.h

Pull spi UAPI disintegration from David Howells:
 "This is to complete part of the Userspace API (UAPI) disintegration
  for which the preparatory patches were pulled recently.  After these
  patches, userspace headers will be segregated into:

        include/uapi/linux/.../foo.h

  for the userspace interface stuff, and:

        include/linux/.../foo.h

  for the strictly kernel internal stuff.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
  Acked-by: Grant Likely <grant.likely@secretlab.ca>"

* tag 'disintegrate-spi-20121009' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate include/linux/spi

Pull OpenRISC uapi disintegration from Jonas Bonn:
 "OpenRISC UAPI disintegration work from David Howells"

* tag 'openrisc-uapi' of git://openrisc.net/jonas/linux:
  UAPI: (Scripted) Disintegrate arch/openrisc/include/asm

Pull user namespace compile fixes from Eric W Biederman:
 "This tree contains three trivial fixes.  One compiler warning, one
  thinko fix, and one build fix"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  btrfs: Fix compilation with user namespace support enabled
  userns: Fix posix_acl_file_xattr_userns gid conversion
  userns: Properly print bluetooth socket uids

Pull md updates from NeilBrown:
 - "discard" support, some dm-raid improvements and other assorted bits
   and pieces.

* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
  md: refine reporting of resync/reshape delays.
  md/raid5: be careful not to resize_stripes too big.
  md: make sure manual changes to recovery checkpoint are saved.
  md/raid10: use correct limit variable
  md: writing to sync_action should clear the read-auto state.
  Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
  md/raid5: make sure to_read and to_write never go negative.
  md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
  md/raid5: protect debug message against NULL derefernce.
  md/raid5: add some missing locking in handle_failed_stripe.
  MD: raid5 avoid unnecessary zero page for trim
  MD: raid5 trim support
  md/bitmap:Don't use IS_ERR to judge alloc_page().
  md/raid1: Don't release reference to device while handling read error.
  raid: replace list_for_each_continue_rcu with new interface
  add further __init annotations to crypto/xor.c
  DM RAID: Fix for "sync" directive ineffectiveness
  DM RAID: Fix comparison of index and quantity for "rebuild" parameter
  DM RAID: Add rebuild capability for RAID10
  DM RAID: Move 'rebuild' checking code to its own function
  ...