This was used in the olden days, back when onions were proper
yellow. Basically it mapped to the current buffer to be
transferred. With highmem being added more than a decade ago,
most drivers map pages out of a bio, and rq->buffer isn't
pointing at anything valid.

Convert old style drivers to just use bio_data().

For the discard payload use case, just reference the page
in the bio.
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch fixes I/O errors with the sym53c8xx_2 driver when the disk
returns QUEUE FULL status.

When the controller encounters an error (including QUEUE FULL or BUSY
status), it aborts all not yet submitted requests in the function
sym_dequeue_from_squeue.

This function aborts them with DID_SOFT_ERROR.

If the disk has full tag queue, the request that caused the overflow is
aborted with QUEUE FULL status (and the scsi midlayer properly retries
it until it is accepted by the disk), but the sym53c8xx_2 driver aborts
the following requests with DID_SOFT_ERROR --- for them, the midlayer
does just a few retries and then signals the error up to sd.

The result is that disk returning QUEUE FULL causes request failures.

The error was reproduced on 53c895 with COMPAQ BD03685A24 disk
(rebranded ST336607LC) with command queue 48 or 64 tags.  The disk has
64 tags, but under some access patterns it return QUEUE FULL when there
are less than 64 pending tags.  The SCSI specification allows returning
QUEUE FULL anytime and it is up to the host to retry.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes the initialization of an array used in the TX
datapath that was mistakenly initialized together with the
RX datapath arrays. An out of range array access could happen
when RX and TX rings had different sizes.
Signed-off-by: NVincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sun4i-emac driver is rather primitive, and doesn't support
promiscuous mode. This makes usage such as bridging impossible,
which is a shame on virtualization capable HW such as the
Allwinner A20.

The fix is fairly simple: move the RX setup code to the ndo_set_rx_mode
vector, and add the required HW configuration when IFF_PROMISC is passed
by the core code.

This has been tested on a generic A20 box running a few virtual
machines hanging off a bridge with the EMAC chip as the link to the
outside world.

Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes coccinelle error regarding usage of IS_ERR and
PTR_ERR instead of PTR_ERR_OR_ZERO.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code was incorrectly using sg_dma_address() and
sg_dma_len() instead of ib_sg_dma_address() and
ib_sg_dma_len().

This prevents srpt from functioning with the
Intel HCA and indeed will corrupt memory
badly.

Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Tested-by: NVinod Kumar <vinod.kumar@intel.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@intel.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Because it doesn't always create, if there's an existing one it just
returns it.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

These functions are not adding or deleting an lport. They are adding a
wwn that may match with an lport that is present on the system.

Renaming ft_del_lport also means we won't have functions named
both ft_del_lport and ft_lport_del any more.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Rename struct ft_lport_acl to ft_lport_wwn. "acl" is associated with
something different in LIO terms. Really, ft_lport_wwn is the
fabric-specific wrapper for the struct se_wwn.

Rename "lacl" local variables to "ft_wwn" as well.

Rename list_heads used as list members to make it clear they're nodes, not
heads.

Rename lport_node to ft_wwn_node.

Rename ft_lport_list to ft_wwn_list
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

tcm_fc doesn't support multiple TPGs per wwn. For proof, see
ft_lport_find_tpg. Enforce this in the code.

Replace ft_lport_wwn.tpg_list with a single pointer. We can't fold ft_tpg
into ft_lport_wwn because they can have different lifetimes.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Nobody outside tfc_conf.c uses it.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

ft_del_tpg checks tpg->tport is set before unlinking the tpg from the
tport when the tpg is being removed. Set this pointer in ft_tport_create,
or the unlinking won't happen in ft_del_tpg and tport->tpg will reference
a deleted object.

This patch sets tpg->tport in ft_tport_create, because that's what
ft_del_tpg checks, and is the only way to get back to the tport to
clear tport->tpg.

The bug was occuring when:

- lport created, tport (our per-lport, per-provider context) is
  allocated.
  tport->tpg = NULL
- tpg created
- a PRLI is received. ft_tport_create is called, tpg is found and
  tport->tpg is set
- tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not
  set, tport->tpg is not cleared and points at freed memory
- Future calls to ft_tport_create return tport via first conditional,
  instead of searching for new tpg by calling ft_lport_find_tpg.
  tport->tpg is still invalid, and will access freed memory.

see https://bugzilla.redhat.com/show_bug.cgi?id=1071340

Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch addresses an issue that occurs when an ABTS is received
for an se_cmd that completes just before the sess_cmd_list is searched
in core_tmr_abort_task(). When the sess_cmd_list is searched, since
the ABTS and the FCP_CMND being aborted (that just completed) both
have the same OXID, TFO->get_task_tag(TMR) returns a value that
matches tmr->ref_task_tag (from TFO->get_task_tag(FCP_CMND)), and
the Abort Task tries to abort itself. When this occurs,
transport_wait_for_tasks() hangs forever since the TMR is waiting
for itself to finish.

This patch adds a check to core_tmr_abort_task() to make sure the
TMR does not attempt to abort itself.
Signed-off-by: NAlex Leung <alex.leung@emulex.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

When the Ethernet interface is put down and up with heavy Ethernet
traffic, then there is prossibility of an interrupt waiting in irq
controller to be processed, so when the interface is brought up again
just after enable interrupt, it goes to ISR due to the previous
unhandled interrutp and in ISR napi is not scheduled as the napi
is not enabled in ndo_open which results in disabled interrupt for
CPSW and no packets are received in cpsw. So this patch moves enabling
of interupts after napi_enable and clearing CPDMA interrupts.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the Ethernet interface is brought down during high Ethernet traffic,
then cpsw creates the following warn dump. When cpdma has already processed
the packet then the status will be greater than 0, so the cpsw_rx_handler
considers that the interface is up and try to resubmit one more rx buffer
to cpdma which fails as the DMA is in teardown process. This can be avoided
by checking the interface state and then process the received packet, if the
interface is down just discard and free the skb and return.

[ 2823.104591] WARNING: CPU: 0 PID: 1823 at drivers/net/ethernet/ti/cpsw.c:711 cpsw_rx_handler+0x148/0x164()
[ 2823.114654] Modules linked in:
[ 2823.117872] CPU: 0 PID: 1823 Comm: ifconfig Tainted: G        W     3.14.0-11992-gf34c4a35 #11
[ 2823.126860] [<c0014b5c>] (unwind_backtrace) from [<c00117e4>] (show_stack+0x10/0x14)
[ 2823.135030] [<c00117e4>] (show_stack) from [<c0533a9c>] (dump_stack+0x80/0x9c)
[ 2823.142619] [<c0533a9c>] (dump_stack) from [<c003f0e0>] (warn_slowpath_common+0x6c/0x90)
[ 2823.151141] [<c003f0e0>] (warn_slowpath_common) from [<c003f120>] (warn_slowpath_null+0x1c/0x24)
[ 2823.160336] [<c003f120>] (warn_slowpath_null) from [<c03caeb0>] (cpsw_rx_handler+0x148/0x164)
[ 2823.169314] [<c03caeb0>] (cpsw_rx_handler) from [<c03c730c>] (__cpdma_chan_free+0x90/0xa8)
[ 2823.178028] [<c03c730c>] (__cpdma_chan_free) from [<c03c7418>] (__cpdma_chan_process+0xf4/0x134)
[ 2823.187279] [<c03c7418>] (__cpdma_chan_process) from [<c03c7560>] (cpdma_chan_stop+0xb4/0x17c)
[ 2823.196349] [<c03c7560>] (cpdma_chan_stop) from [<c03c766c>] (cpdma_ctlr_stop+0x44/0x9c)
[ 2823.204872] [<c03c766c>] (cpdma_ctlr_stop) from [<c03cb708>] (cpsw_ndo_stop+0x154/0x188)
[ 2823.213321] [<c03cb708>] (cpsw_ndo_stop) from [<c046f0ec>] (__dev_close_many+0x84/0xc8)
[ 2823.221761] [<c046f0ec>] (__dev_close_many) from [<c046f158>] (__dev_close+0x28/0x3c)
[ 2823.230012] [<c046f158>] (__dev_close) from [<c0474ca8>] (__dev_change_flags+0x88/0x160)
[ 2823.238483] [<c0474ca8>] (__dev_change_flags) from [<c0474da0>] (dev_change_flags+0x18/0x48)
[ 2823.247316] [<c0474da0>] (dev_change_flags) from [<c04d12c4>] (devinet_ioctl+0x61c/0x6e0)
[ 2823.255884] [<c04d12c4>] (devinet_ioctl) from [<c045c660>] (sock_ioctl+0x68/0x2a4)
[ 2823.263789] [<c045c660>] (sock_ioctl) from [<c0125fe4>] (do_vfs_ioctl+0x78/0x61c)
[ 2823.271629] [<c0125fe4>] (do_vfs_ioctl) from [<c01265ec>] (SyS_ioctl+0x64/0x74)
[ 2823.279284] [<c01265ec>] (SyS_ioctl) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several spots in the kernel perform a sequence like:

	skb_queue_tail(&sk->s_receive_queue, skb);
	sk->sk_data_ready(sk, skb->len);

But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up.  So this skb->len access is potentially
to freed up memory.

Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.

And finally, no actual implementation of this callback actually uses
the length argument.  And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.

So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.

Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ws2008r2 does not support UDP checksum offload. Thus, we cannnot turn on
UDP offload in the host. Also, on ws2012 and ws2012 r2, there appear to be
an issue with UDP checksum offload.
Fix this issue by computing the UDP checksum in the Hyper-V driver.

Based on Dave Miller's comments, in this version, I have COWed the skb
before modifying the UDP header (the checksum field).
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ws2008R2 supports ndis_version 6.1 and 6.1 is the minimal version required
for various offloads. Negotiate ndis_version 6.1 when on ws2008r2.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An outgoing packet can potentially need per-packet information for
all the offloads and VLAN tagging. Fix this issue.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the bonding debug_fs entries when the
module initialization fails. The debug_fs
entries should be removed together with all other
already allocated resources.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NJay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent change broke the RSS LUT programming, causing it to be
programmed with all 0. Correct this by actually assigning the
incremented value back to the counter variable so that the increment
will be remembered by the calling function.

While we're at it, add a proper kernel-doc function comment to our
helper function.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

last_rx_timestamp should be updated only when rx time stamp is
read. Also it's only used with NICs that have per-interface time
stamping resources so it can be moved to adapter structure and
set in igb_ptp_rx_rgtstamp().
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000_hw.c contains a lot of debug messages which print
name of invoked function and contain no new line character
at the end.  Remove them as equivalent information can be
nowadays obtained using function tracer.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

An indication of work queue initialization is needed. This is
because register accesses prior to that time can detect a removal
and attempt to schedule the watchdog task. Adding the
__IXGBEVF_WORK_INIT bit allows this to be checked and if not
set prevent the watchdog task scheduling. By checking for a
removal right after initialization, the probe can be failed
at that point without getting the watchdog task involved.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There needs to be an indication when the service task has been
initialized. This is because register access prior to that time
can detect a removal and attempt to schedule the service task.
Adding the __IXGBE_SERVICE_INITED bit allows this to be checked
and if not set prevent the service task scheduling. By checking
for a removal right after initialization, the probe can be failed
at that point without getting the service task involved.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

async_schedule() sd resume work to allow disks and other devices to
resume in parallel.

This moves the entirety of scsi_device resume to an async context to
ensure that scsi_device_resume() remains ordered with respect to the
completion of the start/stop command.  For the duration of the resume,
new command submissions (that do not originate from the scsi-core) will
be deferred (BLKPREP_DEFER).

It adds a new ASYNC_DOMAIN_EXCLUSIVE(scsi_sd_pm_domain) as a container
of these operations.  Like scsi_sd_probe_domain it is flushed at
sd_remove() time to ensure async ops do not continue past the
end-of-life of the sdev.  The implementation explicitly refrains from
reusing scsi_sd_probe_domain directly for this purpose as it is flushed
at the end of dpm_resume(), potentially defeating some of the benefit.
Given sdevs are quiesced it is permissible for these resume operations
to bleed past the async_synchronize_full() calls made by the driver
core.

We defer the resolution of which pm callback to call until
scsi_dev_type_{suspend|resume} time and guarantee that the callback
parameter is never NULL.  With this in place the type of resume
operation is encoded in the async function identifier.

There is a concern that async resume could trigger PSU overload.  In the
enterprise, storage enclosures enforce staggered spin-up regardless of
what the kernel does making async scanning safe by default.  Outside of
that context a user can disable asynchronous scanning via a kernel
command line or CONFIG_SCSI_SCAN_ASYNC.  Honor that setting when
deciding whether to do resume asynchronously.

Inspired by Todd's analysis and initial proposal [2]:
https://01.org/suspendresume/blogs/tebrandt/2013/hard-disk-resume-optimization-simpler-approach

Cc: Len Brown <len.brown@intel.com>
Cc: Phillip Susi <psusi@ubuntu.com>
[alan: bug fix and clean up suggestion]
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Suggested-by: NTodd Brandt <todd.e.brandt@linux.intel.com>
[djbw: kick all resume work to the async queue]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Fix the macro used to define linear range regulators to include the
number of voltages.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Acked-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

For commands returned with failed status, queue these for resubmission
and continue retrying them until success or for a limited amount of
time. The final timeout was arbitrarily chosen so requests can't be
retried indefinitely.

Since these are requeued on the nvmeq that submitted the command, the
callbacks have to take an nvmeq instead of an nvme_dev as a parameter
so that we can use the locked queue to append the iod to retry later.

The nvme_iod conviently can be used to track how long we've been trying
to successfully complete an iod request. The nvme_iod also provides the
nvme prp dma mappings, so I had to move a few things around so we can
keep those mappings.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
[fixed checkpatch issue with long line]
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

Some programs require HDIO_GETGEO work, which requires we implement
getgeo.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

Done to ensure nvme_thread is not running when there
are no devices to poll.
Signed-off-by: NDan McLeran <daniel.mcleran@intel.com>
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>

Increase the default timeout to 30 seconds to match SCSI.
Signed-off-by: NKeith Busch <keith.busch@intel.com>
[use byte instead of ushort]
Signed-off-by: NMatthew Wilcox <matthew.r.wilcox@intel.com>