The following change is meant to update the adaptive ITR algorithm to
better support the needs of the network. Specifically with this change what
I have done is make it so that our ITR algorithm will try to prevent either
starving a socket buffer for memory in the case of Tx, or overrunning an Rx
socket buffer on receive.

In addition a side effect of the calculations used is that we should
function better with new features such as XDP which can handle small
packets at high rates without needing to lock us into NAPI polling mode.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the
previous check invalid.

Change the check for MNG present to be only based on FWSM.PT bit.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.

- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()

- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe driver have page recycle scheme based around the RX-ring
queue, where a RX page is shared between two packets. Based on the
refcnt, the driver can determine if the RX-page is currently only used
by a single packet, if so it can then directly refill/recycle the
RX-slot by with the opposite "side" of the page.

While this is a clever trick, it is hard to determine when this
recycling is successful and when it fails.  Adding a counter, which is
available via ethtool --statistics as 'alloc_rx_page'.  Which counts
the number of times the recycle fails and the real page allocator is
invoked.  When interpreting the stats, do remember that every alloc
will serve two packets.

The counter is collected per rx_ring, but is summed and ethtool
exported as 'alloc_rx_page'.  It would be relevant to know what
rx_ring that cannot keep up, but that can be exported later if
someone experience a need for this.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit: fed21bcee7a5
("ixgbe: Don't bother clearing buffer memory for descriptor rings)

exposed some issues with the logic in the current implementation of
ixgbe_clean_test_rings() that are being addressed in this patch:

- Split the clearing of the Tx and Rx rings in separate loops. Previously
both Tx and Rx rings were cleared in a rx_desc->wb.upper.length based
loop which could lead to issues if for w/e reason packets were received
outside of the frames transmitted for the loopback test.

- Add check for IXGBE_TXD_STAT_DD to avoid clearing the rings if the
transmits have not comlpeted by the time we enter ixgbe_clean_test_rings()

- Exit early on ixgbe_check_lbtest_frame() failure.

This change fixes a crash during ethtool diagnostic (ethtool -t).
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ignoring errors when attempting to identify the PHY can lead to a crash.
Specifically in the case of FW controlled PHYs where the PHY read/write
operations are set to NULL.

Removed redundant comment.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just like when the last VF is removed, we need to restore normal
operations after the last macvlan offload is removed, else we
get stuck in single queue operations.

To test:
ethtool -l eth1   # note the number of queues in use, ~= cpus

ethtool -K eth1 l2-fwd-offload on
ip link add mv1 link eth1 type macvlan mode bridge
ip link set dev mv1 up
ip link del mv1

ethtool -l eth1   # are we back to the same # of queues, or stuck on 1?
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Declare ixgbe_mac_operations structures as const as they are only stored
in the mac_ops field of ixgbe_info structure. This field is of type
const and therefore ixgbe_mac_operations structure can be made const
too.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added clearing of SW resource bits in the SW/FW synchronization
register to ixgbe_init_swfw_sync_X540().

Updated ixgbe_acquire_swfw_sync_X540 SW Manageability host interface
resource bit error case to match the error handling of the other SW
resource bits. Which is to release the SW resource bits if SW times
out while attempting to acquire the resource.

This allows the driver to load in cases where the semaphore bits
could be stuck after a reset or a crash.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

dcb_app priority is unsigned thus checking whether it is less than zero
is redundant.
Signed-off-by: NChristos Gkekas <chris.gekas@gmail.com>
Acked-By: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many macros in dwmac-ipq806x are unused and should be removed.
Moreover gmac->id is an unsigned variable and therefore checking
whether it is less than zero is redundant.
Signed-off-by: NChristos Gkekas <chris.gekas@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch supports the options to switch TCP hash level between
L3 and L4 by ethtool command. TCP over IPv4 and v6 can be set
differently. The default hash level is L4. We currently only
allow switching TX hash level from within the guests.

For example, for TCP over IPv4 on eth0:
To include TCP port numbers in hashing:
	ethtool -N eth0 rx-flow-hash tcp4 sdfn
To exclude TCP port numbers in hashing:
	ethtool -N eth0 rx-flow-hash tcp4 sd
To show TCP hash level:
	ethtool -n eth0 rx-flow-hash tcp4
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This simplifies the logic and make it easier to add more
options.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code that actually takes care of bridge offload introduces a few
more non-trivial constraints with regards to bridge enslavements.
Propagate extack there to indicate the reason.

$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20
$ ip link add name br0 type bridge
$ ip link set dev enp1s0np1.10 master br0
$ ip link set dev enp1s0np1.20 master br0
Error: spectrum: Can not bridge VLAN uppers of the same port.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to physical ports, enslavement of VLAN devices can also fail.
Use extack to indicate why the enslavement failed.

$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add name bond0 type bond mode 802.3ad
$ ip link set dev enp1s0np1.10 master bond0
Error: spectrum: VLAN devices only support bridge and VRF uppers.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of zeroing out bnxt_tc.c with a #ifdef foo, instead don't compile
the file when the option is not enabled. Now make and the preprocessor do
not have to waste time compiling a no-op.
Signed-off-by: NJonathan Toppins <jtoppins@redhat.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use pci_ari_enabled() from the PCI core instead of the identical local copy
bnx2x_ari_enabled().  No functional change intended.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set TCP/UDP actions. This
patch enables TC flower offload of set TCP/UDP sport and dport actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set IPv6 actions. This
patch enables TC flower offload of set IPv6 src and dst address actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set IPv4 actions. This
patch enables TC flower offload of set IPv4 src and dst address actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set ethernet actions.
This patch enables TC flower offload of set ethernet actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously matching on IPv6 ttl and tos fields were not offloaded. This
patch enables offloading IPv6 ttl and tos as match fields.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously matching on IPv4 ttl and tos fields were not offloaded. This
patch enables offloading IPv4 ttl and tos as match fields.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously MPLS match offloading was not supported. This patch enables
MPLS match offloading support for label, bos and tc fields.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we've reduced the number of flags, organize similar flags
together and re-number them accordingly.

Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.

One alternative approach considered, but not implemented here, was to
use an enumeration for the flag variables, and create a macro
I40E_FLAG() which used string concatenation to generate BIT_ULL values.
This has the advantage of making the actual bit values compile-time
dynamic so that we do not need to worry about matching the order to the
bit value. However, this does produce a high level of code churn, and
makes it more difficult to read a dumped flags value when debugging.

Change-ID: I8653fff69453cd547d6fe98d29dfa9d8710387d1
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 6a7fded7 ("i40e: Fix RS bit update in Tx path and
disable force WB workaround") we've tried to "optimize" setting the
RS bit based around skb->xmit_more. This same logic was refactored
in commit 1dc8b538 ("i40e: Reorder logic for coalescing RS bits"),
but ultimately was not functionally changed.

Using skb->xmit_more in this way is incorrect, because in certain
circumstances we may see a large number of skbs in sequence with
xmit_more set. This leads to a performance loss as the hardware does not
writeback anything for those packets, which delays the time it takes for
us to respond to the stack transmit requests. This significantly impacts
UDP performance, especially when layered with multiple devices, such as
bonding, VLANs, and vnet setups.

This was not noticed until now because it is difficult to create a setup
which reproduces the issue. It was discovered in a UDP_STREAM test in
a VM, connected using a vnet device to a bridge, which is connected to
a bonded pair of X710 ports in active-backup mode with a VLAN. These
layered devices seem to compound the number of skbs transmitted at once
by the qdisc. Additionally, the problem can be masked by reducing the
ITR value.

Since the original commit does not provide strong justification for this
RS bit "optimization", revert to the previous behavior of setting the RS
bit every 4th packet.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent commit 809481484e5d ("i40e/i40evf: support for VF VLAN tag
stripping control") added support for VFs to negotiate the control of
VLAN tag stripping. This should have allowed VFs to disable the feature.
Unfortunately, the flag was set only in netdev->feature flags and not in
netdev->hw_features.

This ultimately causes the stack to assume that it cannot change the
flag, so it was unchangeable and marked as [fixed] in the ethtool -k
output.

Fix this by setting the feature in hw_features first, just as we do for
the PF code. This enables ethtool -K to disable the feature correctly,
and fully enables user control of the VLAN tag stripping feature.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous implementation of LED set/get functions required to enter
PHY debug mode, in order to prevent access to it from FW and SW at
the same time. Reset of all ports was a unwanted side effect.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements the PCI error handler reset_prepare and reset_done.
This allows us to handle function level reset.  Without this patch we
are unable to perform and recover from an FLR correctly and this will cause
VFs to be unable to recover from an FLR on the PF.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there is no space for more flow director filters and user requested to
add a new one it is rejected by firmware and automatically removed from the
filter list maintained by driver. This behaviour is correct. Afterwards
existing filter can be removed making free slot for the new one. This
however causes the newly added filter to be accepted by firmware but
removed from driver filter list resulting in not showing after issuing
'ethtool -n <dev_name>'.

This happened due to not clearing the variable pf->fd_inv which stores
filter number to be removed from the list when firmware refused to add the
requested filter. It caused the filter with this specific ID to be
constantly removed once it was added to the list although it has been
accepted by firmware and effectively applied to the NIC.
It was fixed by clearing pf->fd_inv variable after removal of the filter
from the list when it was rejected by firmware.
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch causes error message to be displayed when NIC detects
insertion of module that does not meet thermal requirements.
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes some code that was accidentally added to
the wrong function with a merge error.  Fixes: c53934c6
("i40e: fix: do not sleep in netdev_ops")
Signed-off-by: NAlice Michael <alice.michael@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When using set_bit and friends, we should be using actual
bitmaps, and fix all the locations where we might access
it.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This register was defined incorrectly. Fix the increment value to 8, and
replace the iterator with _i to make the definition consistent with
other statistics registers.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since I40E_PHY_TYPE_MAX is used as an iterator, usually combined with
some sort of bit-shifting, it should only include actual PHY types and
not error cases. Move it up in the enum declaration so that loops only
iterate across valid PHY types.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Starting with XL710 FW 5.3 PTP L4 was disabled for XL710 due to a bug.  The
bug has since been resolved in XL710 FW >6.0 and PTP L4 can now be
re-enabled on those devices with updated firmware.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, when setting up the IRQ for a q_vector, we set an affinity
hint based on the v_idx of that q_vector. Meaning a loop iterates on
v_idx, which is an incremental value, and the cpumask is created based
on this value.

This is a problem in systems with multiple logical CPUs per core (like in
simultaneous multithreading (SMT) scenarios). If we disable some logical
CPUs, by turning SMT off for example, we will end up with a sparse
cpu_online_mask, i.e., only the first CPU in a core is online, and
incremental filling in q_vector cpumask might lead to multiple offline
CPUs being assigned to q_vectors.

Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.

In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1)  where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.

Instead, we should only assign hints for CPUs which are online. Even
better, the kernel already provides a function, cpumask_local_spread()
which takes an index and returns a CPU, spreading the interrupts across
local NUMA nodes first, and then remote ones if necessary.

Since we generally have a 1:1 mapping between vectors and CPUs, there
is no real advantage to spreading vectors to local CPUs first. In order
to avoid mismatch of the default XPS hints, we'll pass -1 so that it
spreads across all CPUs without regard to the node locality.

Note that we don't need to change the q_vector->affinity_mask as this is
initialized to cpu_possible_mask, until an actual affinity is set and
then notified back to us.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By default, our devices do source pruning, that is, they drop receive
packets that have the source MAC matching one of the receive filters.
Unfortunately, this breaks ARP monitoring in channel bonding, as the
bonding driver expects devices to receive ARPs containing their own
source address.

Add an ethtool private flag to control this feature.

Also, remove the netif_running() check when we process our private
flags. It's OK to reset when the device is closed and in most cases we
need the reset the apply these changes.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a typo in i40e_pf object documentation; num_req_vfs
refers to the number of VFs requested for the PF.
Signed-off-by: NRami Rosen <rami.rosen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function emac_isr is local to the source and does not need to
be in global scope, so make it static.

Cleans up sparse warnings:
symbol 'emac_isr' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>