This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev.  From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.

So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Consolidate the calls to ASSERT_RTNL() before bond_select_active_slave()
inside bond_select_active_slave() itself and remove the ASSERT_RTNL()
from bond_hw_addr_swap() as it's not exported and its only caller -
bond_change_active_slave() already has an ASSERT_RTNL().
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First adjust a couple of locking comments that were left inaccurate,
then adjust comments to use the netdev styling and remove extra new
lines where necessary and add a couple of new lines between declarations
and code. These are all trivial styling changes, no functional change.
Also removed a couple of outdated or obvious comments.
This patch is by no means a complete fix of all netdev style violations
but it gets the bonding closer.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__rlb_next_rx_slave() is a copy of rlb_next_rx_slave() with the
difference that it uses rcu primitives to walk the slave list. We don't
need the two functions and can make rlb_next_rx_slave() a wrapper for
callers which hold RTNL.
So add a comment and ASSERT_RTNL() to make sure what is intended.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: ethernet: neterion: vxge: vxge-main.c: Cleaning up missing null-terminate in conjunction with strncpy

Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: ethernet: freescale: fec_main.c: Cleaning up missing null-terminate in conjunction with strncpy

Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use container_of instead of casting first structure member.

Compiled but untested.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use container_of instead of casting first structure member.

ARM cross-compiled but untested.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print the IP revision when probing.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Software clear the MDIO interrupt before MDIO bus access, but
MAC still generate MDIO interrupt. The issue only happen on
imx6slx chip.

CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc1-00399-g0bcad17 #315
Backtrace:
[<800121fc>] (dump_backtrace) from [<800124e0>] (show_stack+0x18/0x1c)
 r6:8096e534 r5:8096e534 r4:00000000 r3:00000000
[<800124c8>] (show_stack) from [<806a4c60>] (dump_stack+0x8c/0xa4)
[<806a4bd4>] (dump_stack) from [<80060ab8>] (__lock_acquire+0x1814/0x1c40)
 r6:be078000 r5:be074000 r4:be03f6e4 r3:be078000
[<8005f2a4>] (__lock_acquire) from [<800616e0>] (lock_acquire+0x70/0x84)
 r10:809ada33 r9:be010600 r8:00000096 r7:00000001 r6:be074000 r5:00000000
 r4:60000193
[<80061670>] (lock_acquire) from [<806abb20>] (_raw_spin_lock_irqsave+0x40/0x54)
 r7:00000000 r6:8005a3f8 r5:00000193 r4:be03f6d4
[<806abae0>] (_raw_spin_lock_irqsave) from [<8005a3f8>] (complete+0x1c/0x4c)
 r6:80950904 r5:be03f6d0 r4:be03f6d4
[<8005a3dc>] (complete) from [<8041b4c0>] (fec_enet_interrupt+0x128/0x164)
 r6:80950904 r5:00800000 r4:be03f000 r3:00000000
[<8041b398>] (fec_enet_interrupt) from [<8006aeac>] (handle_irq_event_percpu+0x38/0x13c)
 r6:00000000 r5:be01065c r4:be399e00 r3:8041b398
[<8006ae74>] (handle_irq_event_percpu) from [<8006aff4>] (handle_irq_event+0x44/0x64)
 r10:be03f000 r9:80989fe0 r8:00000000 r7:00000096 r6:be399e00 r5:be01065c
 r4:be010600
[<8006afb0>] (handle_irq_event) from [<8006e3e8>] (handle_fasteoi_irq+0xc8/0x1bc)
 r6:8096e764 r5:be01065c r4:be010600 r3:00000000
[<8006e320>] (handle_fasteoi_irq) from [<8006a63c>] (generic_handle_irq+0x30/0x44)
 r6:be074010 r5:80945e4c r4:00000096 r3:8006e320
[<8006a60c>] (generic_handle_irq) from [<8000f218>] (handle_IRQ+0x54/0xbc)
 r4:80950d74 r3:00000180
[<8000f1c4>] (handle_IRQ) from [<800086cc>] (gic_handle_irq+0x30/0x68)
 r8:be3ab478 r7:c080e100 r6:be075bd8 r5:80950eec r4:c080e10c r3:000000a0
[<8000869c>] (gic_handle_irq) from [<80013064>] (__irq_svc+0x44/0x5c)
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add compatible string "fsl,imx6sx-fec" for i.MX6SX.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues.
For tx queues: ring 0 -> best effort
	       ring 1 -> Class A
	       ring 2 -> Class B
For rx queues:
	       ring 0 -> best effort
	       ring 1 -> receive VLAN packet with classification match
	       ring 2 -> receive VLAN packet with classification match

Add enet-avb IP multiqueue support for the driver.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For i.MX6SX enet use AXI bus, reset MAC will make system bus dead
if ENET-AXI bus has pending access (AHB bus should not have such issue).
So, disable enet with AVB MAC instead of reset MAC itself.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

initilized all queues according to queue number get from DT file.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDuan Fugang <B38611@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
	fsl,num-tx-queues=<3>;
	fsl,num-rx-queues=<3>

Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch just change data structure to support multi-queue.
Only 1 queue enabled.

Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdfSigned-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <frank.li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add enet AVB feature macro define for imx6sx.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
	 For imx6sx, it alos is the clock source of interrupt coalescing.
	 The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
	 the refrence clock is 125Mhz coming from internal PLL or external.
	 In i.MX6sx-arm2 board, the clock is from internal PLL.
	 clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
	 clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.

The patch add clk_ref to distiguish the different clocks.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the Marvell driver with some cleanups by Claudio Leite
and myself.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Cc: Claudio Leite <leitec@staticky.com>
Signed-off-by: NClaudio Leite <leitec@staticky.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently PCIe error reporting is enabled only on PFs. This patch enables
this feature on VFs too as Lancer VFs support it.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report the ethtool port-type/supported/advertising values based on the
cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from
the transceiver data fetched from the FW.
Signed-off-by: NRavikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the dump-module-eeprom and module-info
ethtool options.
Signed-off-by: NMark Leonard <mark.leonard@emulex.com>
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some configurations the FW doesn't allow changing flow control settings
of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW
doesn't report an error to the driver.
Signed-off-by: NSuresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the RX path, the driver currently consumes upto 64 (budget) packets in
one NAPI sweep. When the size of the packet received is larger than a
fragment size (2K), more than one fragment is consumed for each packet.
As the driver currently posts a max of 64 fragments, all the consumed
fragments may not be replenished. This can cause avoidable drops in RX path.
This patch fixes this by posting a max(consumed_frags, 64) frags. This is
done only when there are atleast 64 free slots in the RXQ.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace strcpy with strlcpy, as it avoids a possible buffer overflow.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following minor issues with log messages in be2net:
  1) Period is not required at the end of log message.
  2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely
     ignore async events from FW it's not interested in.
  3) Reword a log message for better readability to say that SRIOV
     "is disabled" rather than "not supported".
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1 ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.

Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support hw VLAN for tx and rx. And enable them by default.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that locks have been removed, remove some unnecessary comments and
adjust others to reflect reality. Also add a comment to "mode_lock" to
describe its current users and give a brief summary why they need it.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have bond->mode_lock, we can remove the state_machine_lock
and use it in its place. There're no fast paths requiring the per-port
spinlocks so it should be okay to consolidate them into mode_lock.
Also move it inside the unbinding function as we don't want to expose
mode_lock outside of the specific modes.
Suggested-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ALB/TLB specific spinlocks are no longer necessary as we now have
bond->mode_lock for this purpose, so convert them and remove them from
struct alb_bond_info.
Also remove the unneeded lock/unlock functions and use spin_lock/unlock
directly.
Suggested-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

curr_slave_lock is now a misleading name, a much better name is
mode_lock as it'll be used for each mode's purposes and it's no longer
necessary to use a rwlock, a simple spinlock is enough.
Suggested-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly all users of curr_slave_lock already have RTNL as we've discussed
previously so there's no point in using it, the one case where the lock
must stay is the 3ad code, in fact it's the only one.
It's okay to remove it from bond_do_fail_over_mac() as it's called with
RTNL and drops the curr_slave_lock anyway.
bond_change_active_slave() is one of the main places where
curr_slave_lock was used, it's okay to remove it as all callers use RTNL
these days before calling it, that's why we move the ASSERT_RTNL() in
the beginning to catch any potential offenders to this rule.
The RTNL argument actually applies to all of the places where
curr_slave_lock has been removed from in this patch.
Also remove the unnecessary bond_deref_active_protected() macro and use
rtnl_dereference() instead.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First in rlb_teach_disabled_mac_on_primary() it's okay to remove
curr_slave_lock as all callers except bond_alb_monitor() already hold
RTNL, and in case bond_alb_monitor() is executing we can at most have a
period with bad throughput (very unlikely though).
In bond_alb_monitor() it's okay to remove the read_lock as the slave
list is walked with RCU and the worst that could happen is another
transmitter at the same time and thus for a period which currently is 10
seconds (bond_alb.h: BOND_ALB_LP_TICKS).
And bond_alb_handle_active_change() is okay because it's always called
with RTNL. Removed the ASSERT_RTNL() because it'll be inserted in the
parent function in a following patch.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the read_lock in bond_3ad_lacpdu_recv() since when the slave is
being released its rx_handler is removed before 3ad unbind, so even if
packets arrive, they won't see the slave in an inconsistent state.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the only driver which doesn't hand virtqueue_add_inbuf and
virtqueue_add_outbuf a well-formed, well-terminated sg.  Fix it,
so we can make virtio_add_* simpler.

pktgen results:
	modprobe pktgen
	echo 'add_device eth0' > /proc/net/pktgen/kpktgend_0
	echo nowait 1 > /proc/net/pktgen/eth0
	echo count 1000000 > /proc/net/pktgen/eth0
	echo clone_skb 100000 > /proc/net/pktgen/eth0
	echo dst_mac 4e:14:25:a9:30:ac > /proc/net/pktgen/eth0
	echo dst 192.168.1.2 > /proc/net/pktgen/eth0
	for i in `seq 20`; do echo start > /proc/net/pktgen/pgctrl; tail -n1 /proc/net/pktgen/eth0; done

Before:
  746547-793084(786421+/-9.6e+03)pps 346-367(364.4+/-4.4)Mb/sec (346397808-367990976(3.649e+08+/-4.5e+06)bps) errors: 0

After:
  767390-792966(785159+/-6.5e+03)pps 356-367(363.75+/-2.9)Mb/sec (356068960-367936224(3.64314e+08+/-3e+06)bps) errors: 0
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending out a burst of packets across multiple descriptors,
it is sufficient to send one LDC "start" trigger for
the first descriptor, so do not send an LDC "start" for every
pass through vnet_start_xmit. Similarly, it is sufficient to send
one "DRING_STOPPED" trigger for the last dring (and if that
fails, hold off and send the trigger later).

Optimizations to the number of LDC messages helps avoid
filling up the LDC channel with superfluous LDC messages
that risk triggering flow-control on the channel,
and also boosts performance.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: NRaghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>