If the write protect pad of the controller is not connected to the write
protect pin of the slot, the driver should be notified of this condition
so that incorrect check for write protection by reading the WRTORT
register can avoided. The get_ro platform callback can be used for in
such cases, but with device tree support enabled, such platform callbacks
cannot be supported.

Add a new quirk for notifying the driver about the missing write protect
line so the driver can assume that the card write protection is disabled.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some platforms allow for clock gating and control of bus interface unit
clock and card interface unit clock. Add support for clock lookup of
optional biu and ciu clocks for clock gating and clock speed
determination.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Instead of aborting the probe when a slot initialization fails, allow
initialization of as many slots as possible. If there is at least one
instance of a slot that is successfully initialized, allow the driver
probe to succeed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use devm_* managed functions for simpler error handling.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The 'struct dw_mci' maintains a copy of the pdev->dev instance instead of
maintaining a reference to that 'struct device' instance. Any resource
allocated using the device resource management kernel API with the instance
of 'struct device' in 'struct dw_mci' is then incorrect. Fix this by
converting the copy of 'struct device' in 'struct dw_mci' to a reference.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Previously to this patch, an SDHCI platform that uses a GPIO for
card detection instead of the internal SDHCI_CARD_PRESENT bit on
the presence register would fail to detect a new card.

Some drivers worked around this in various ways: esdhc-imx defines
an IO accessor to fake the presence bit being true, s3c turns on
polling (which stops the SDHCI driver from checking the bit) after
a card's inserted.  But none of this should be necessary; the real
fix is to check whether we're using a GPIO and avoid relying on
the presence bit if so, as this patch implements.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Removes use of the DaVinci EDMA private DMA API and replaces
it with use of the DMA engine API.
Signed-off-by: NMatt Porter <mporter@ti.com>
Tested-by: NKoen Kooi <koen@dominion.thruhere.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

Tested on OLPC XO-4/MMP3, where the card detection pin for one of
the controllers is a sideband GPIO.  The third cell in the cd-gpios
property controls whether the GPIO is active high/active low.

(Also, pass host_caps2 through from platdata to the mmc host.)
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
[kliu5@marvell.com: Compile fix]
Signed-off-by: NChris Ball <cjb@laptop.org>

module_pci_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NHarald Welte <laforge@gnumonks.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

module_pci_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

module_pci_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes the checkpatch error and warnings listed below:

ERROR: return is not a function, parentheses are not required
WARNING: Prefer pr_err(... to printk(KERN_ERR, ...
WARNING: quoted string split across lines
WARNING: line over 80 characters
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fixed the below message.

WARNING: drivers/mmc/host/built-in.o(.text+0x5ee8): Section mismatch in reference from the function dw_mci_probe() to the function .init.text:dw_mci_init_slot()
The function dw_mci_probe() references
the function __init dw_mci_init_slot().
This is often because dw_mci_probe lacks a __init
annotation or the annotation of dw_mci_init_slot is wrong
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When compiling a kernel that supports only Tegra30 and not Tegra20,
the SDHCI driver will fail to compile since the of_match_device() failure
fallback code unconditinally references soc_data_tegra20, which is only
compiled in when Tegra20 support is enabled.

In Kernel 3.7, both Tegra20 and Tegra30 will only support booting using
device tree, Hence, there is never a need to fall back to using
soc_data_tegra20 if of_mach_device() fails. Instead, make this case an
error. This removes the reference to soc_data_tegra20, and hence solves
the compile failure.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Consolidate the duplicated code around the handling of CMD_TIMEOUT,
CMD_CRC, DATA_TIMEOUT, DATA_CRC and CARD_ERR handling into a single
function.

This generally shrinks code bloat, but is also required for implementing
software based guard timers.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Flushing spurious IRQs from HSMMC IP is done twice in omap_hsmmc_irq
and omap_hsmmc_do_irq.  Consolidate them to one location.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SYSCONFIG register of HSMMC IP is managed by the omap hwmod
abstraction layer. Resetting the IP and configuring the correct
SYSCONFIG mode is centrally managed by hwmod.

Remove code which manipulates IP reset and SYSCONFIG directly in
the driver.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some straight forward cleanup of unnecessary #include's and host
variables. Some of the verbose and redundant debug messages are
converted to use dev_vdbg.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The function mmc_omap_report_irq uses raw printks and the actual output
was disabled by a static variable. Make the function use dev_vdbg macro
and use it under the standard CONFIG_MMC_DEBUG flag.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Get rid of some unnecessary includes in the driver and
a few unused variables.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Without reset, SD controller may stay in disable mode, SD card can't
be detected when resume from power saving mode.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc core suspend and resume functions had already called sdh_set_ios
with proper flags.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBob Liu <lliubbo@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In BF60x RSI controller:
1) MMR read/write width differs.
2) PWR and CTL MMRs are merged to together.
3) ROD and PD_DAT3 bit masks are obsolete.
4) New RSI block size MMR is defined.
5) The definition of DMA descriptor set size is changed.
6) set_ios should powers up controller in 2 steps.

In addition, this patch cleans up the spin locks.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

bf518 RSI dma doesn't work in array mode.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

1/ If regulator_get fails, return an error.  This is important if
   it failed with EPROBE_DEFER, as the probe needs to be deferred.

2/ Don't set .set_power until the regulator has been found, or
   the deferred probe will not bother calling omap_hsmmc_reg_get().
Signed-off-by: NNeilBrown <neilb@suse.de>
Acked-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add missing usb_free_urb on failure path after usb_alloc_urb.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@km exists@
local idexpression e;
expression e1,e2,e3;
type T,T1;
identifier f;
@@

* e = usb_alloc_urb(...)
... when any
    when != e = e1
    when != e1 = (T)e
    when != e1(...,(T)e,...)
    when != &e->f
if(...) { ... when != e2(...,(T1)e,...)
                 when != e3 = e
                 when forall
(
             return <+...e...+>;
|
*             return ...;
) }
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds device tree support and binding documentation for
sdhci-dove.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Prepare the clock before enabling it.
Signed-off-by: NChao Xie <xiechao.mail@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The vmmc regulator should not rely on the platform code to enable it.
Expliciitly enable and disable the regulator inside the driver.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

On some systems the host controller does not support vccq
signaling.  This is supplied by a dedicated regulator (vqmmc).
Add support for this regulator.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The register of eSDHC Host Controller Capabilities is not compatible with
standard SDHC register, and eSDHC cannot support End Attribute in NOP ADMA
descriptor. With this patch eSDHC can works in ADMA mode and performance
can be improved.
Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: NPan Jiafei <Jiafei.Pan@freescale.com>
Signed-off-by: NJason Jin <Jason.jin@freescale.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

After commit 26b88520 ("mmc:
omap_hsmmc: remove private DMA API implementation"), the Nokia N800
here stopped booting:

[    2.086181] Waiting for root device /dev/mmcblk0p1...
[    2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000
[    2.331451] Internal error: : 406 [#1] ARM
[    2.335784] Modules linked in:
[    2.339050] CPU: 0    Not tainted  (3.6.0-rc3 #60)
[    2.344146] PC is at default_idle+0x28/0x30
[    2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0

...

This turned out to be due to memory corruption caused by long-broken
PIO code in drivers/mmc/host/omap.c.  (Previously, this driver had
been using DMA; but the above commit caused the MMC driver to fall
back to PIO mode with an unmodified Kconfig.)

The PIO code, added with the rest of the driver in commit
730c9b7e ("[MMC] Add OMAP MMC host
driver"), confused bytes with 16-bit words.  This bug caused memory
located after the PIO transfer buffer to be corrupted with transfers
larger than 32 bytes.  The driver also did not increment the buffer
pointer after the transfer occurred.  This bug resulted in data
corruption during any transfer larger than 64 bytes.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.

The best place I could find to do this is when the SDIO interrupt
was first enabled.  I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.

Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.5, 3.6]
Signed-off-by: NChris Ball <cjb@laptop.org>