According to the SRP standard the INITIATOR and TARGET PORT IDENTIFIER
fields from the login request specify the I_T nexus. Whether or not an
SRP target closes an existing connection for an I_T nexus when a login
request is received depends on the value of the MULTICHANNEL field in
the login request. The SRP initiator derives the value of the
INITIATOR and TARGET PORT IDENTIFIER fields from the .id_ext,
.ioc_guid, .initiator_ext .sgid members of the srp_target_port
structure. This means that the .rdma_cm.dst check must be removed from
srp_conn_unique(). This patch avoids that for target ports that have
multiple addresses, e.g. an IPv4 and an IPv6 address, and if a
connection is established to both target port addresses, that the
initiator logs in alternatingly every 10 seconds to the other target
port address. An SRP target must namely terminate all but one
connections for a given I_T nexus if the MULTICHANNEL field has not
been set in the login request.

Fixes: 19f31343 ("IB/srp: Add RDMA/CM support")
Signed-off-by: NBart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Enable RAW QP to be able to configure burst control by modify_qp. By
using burst control with rate limiting, user can achieve best
performance and accuracy. The burst control information is passed by
user through udata.

This patch also reports burst control capability for mlx5 related
hardwares, burst control is only marked as supported when both
packet_pacing_burst_bound and packet_pacing_typical_size are
supported.
Signed-off-by: NBodong Wang <bodong@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Add two new parameters: max_burst_sz and typical_pkt_size (both
in bytes) to rate limit configurations.

max_burst_sz: The device will schedule bursts of packets for an
SQ connected to this rate, smaller than or equal to this value.
Value 0x0 indicates packet bursts will be limited to the device
defaults. This field should be used if bursts of packets must be
strictly kept under a certain value.

typical_pkt_size: When the rate limit is intended for a stream of
similar packets, stating the typical packet size can improve the
accuracy of the rate limiter. The expected packet size will be
the same for all SQs associated with the same rate limit index.

Ethernet driver is updated according to this change, but these two
parameters will be kept as 0 due to lacking of proper way to get the
configurations from user space which requires to change
ndo_set_tx_maxrate interface.
Signed-off-by: NBodong Wang <bodong@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The data in resp will be copied from kernel to userspace, thus it needs to
be initialized to zeros to avoid copying uninited stack memory.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: e088a685 ("RDMA/hns: Support rq record doorbell for the user space")
Signed-off-by: NYixian Liu <liuyixian@huawei.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

ib_peek_cq() verb doesn't seem be implemented in current code.
There is some past reference to it at [1] about it being unimplemented.

Lot of user documentation created out of kdoc refers to this
unimplemented API. Therefore, remove unimplemented API.

[1] http://lists.openfabrics.org/pipermail/ofw/2008-May/002465.htmlSigned-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Use rdma_is_port_valid() which performs port validity check instead of
open coding the same check.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

What is going on here is a bit subtle, in the kernel there is no
problem because the struct is copied using copy_from_user, so it
can safely have an 8 byte alignment, however in userspace it must
be constructed by concatenation with the ib_uverbs_alloc_pd_resp
struct. This is due to the required memory layout to execute the
command.

Since ibv_uverbs_alloc_pd_resp is only 4 bytes long, this causes
misalignment, and the user space will experience an unexpected padding.
Currently it works around this via pointer maths.

Make everything more robust by having the compiler reduce the alignment
of the struct to 4. The userspace has assertions to ensure this
works properly in all situations.
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Before commit f1b65df5 ("IB/mlx5: Add support for active_width and
active_speed in RoCE"), the mlx5_ib driver set the default active_width
and active_speed to IB_WIDTH_4X and IB_SPEED_QDR.

When the RoCE port is down, the RoCE port does not negotiate the active
width with the remote side, causing the active width to be zero. When
running userspace ibstat to view the port status, ibstat will panic as it
reads an invalid width from sys file.

This patch restores the original behavior.

Fixes: f1b65df5 ("IB/mlx5: Add support for active_width and active_speed in RoCE").
Signed-off-by: NHonggang Li <honli@redhat.com>
Reviewed-by: NHal Rosenstock <hal@mellanox.com>
Reviewed-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Before commit f1b65df5 ("IB/mlx5: Add support for active_width and
active_speed in RoCE"), the mlx5_ib driver set default active_width and
active_speed to IB_WIDTH_4X and IB_SPEED_QDR.

Now, the active_width and active_speed are zeros if the RoCE port
is in DOWN state. The speed string should be set to " SDR" instead of
a blank string when active_speed is zero.
Signed-off-by: NHonggang Li <honli@redhat.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The restrack code relies on the fact that object structures are zeroed at
the allocation stage, the mlx4 CQ wasn't allocated with kzalloc and it
caused to the following crash.

[  137.392209] general protection fault: 0000 [#1] SMP KASAN PTI
[  137.392972] CPU: 0 PID: 622 Comm: ibv_rc_pingpong Tainted: G        W        4.16.0-rc1-00099-g00313983 #11
[  137.395079] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
[  137.396866] RIP: 0010:rdma_restrack_del+0xc8/0xf0
[  137.397762] RSP: 0018:ffff8801b54e7968 EFLAGS: 00010206
[  137.399008] RAX: 0000000000000000 RBX: ffff8801d8bcbae8 RCX: ffffffffb82314df
[  137.400055] RDX: dffffc0000000000 RSI: dffffc0000000000 RDI: 70696b533d454741
[  137.401103] RBP: ffff8801d90c07a0 R08: ffff8801d8bcbb00 R09: 0000000000000000
[  137.402470] R10: 0000000000000001 R11: ffffed0036a9cf52 R12: ffff8801d90c0ad0
[  137.403318] R13: ffff8801d853fb20 R14: ffff8801d8bcbb28 R15: 0000000000000014
[  137.404736] FS:  00007fb415d43740(0000) GS:ffff8801e5c00000(0000) knlGS:0000000000000000
[  137.406074] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  137.407101] CR2: 00007fb41557df20 CR3: 00000001b580c001 CR4: 00000000003606b0
[  137.408308] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  137.409352] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  137.410385] Call Trace:
[  137.411058]  ib_destroy_cq+0x23/0x60
[  137.411460]  uverbs_free_cq+0x37/0xa0
[  137.412040]  remove_commit_idr_uobject+0x38/0xf0
[  137.413042]  _rdma_remove_commit_uobject+0x5c/0x160
[  137.413782]  ? lookup_get_idr_uobject+0x39/0x50
[  137.414737]  rdma_remove_commit_uobject+0x3b/0x70
[  137.415742]  ib_uverbs_destroy_cq+0x114/0x1d0
[  137.416260]  ? ib_uverbs_req_notify_cq+0x160/0x160
[  137.417073]  ? kernel_text_address+0x5c/0x90
[  137.417805]  ? __kernel_text_address+0xe/0x30
[  137.418766]  ? unwind_get_return_address+0x2f/0x50
[  137.419558]  ib_uverbs_write+0x453/0x6a0
[  137.420220]  ? show_ibdev+0x90/0x90
[  137.420653]  ? __kasan_slab_free+0x136/0x180
[  137.421155]  ? kmem_cache_free+0x78/0x1e0
[  137.422192]  ? remove_vma+0x83/0x90
[  137.422614]  ? do_munmap+0x447/0x6c0
[  137.423045]  ? vm_munmap+0xb0/0x100
[  137.423481]  ? SyS_munmap+0x1d/0x30
[  137.424120]  ? do_syscall_64+0xeb/0x250
[  137.424984]  ? entry_SYSCALL_64_after_hwframe+0x21/0x86
[  137.425611]  ? lru_add_drain_all+0x270/0x270
[  137.426116]  ? lru_add_drain_cpu+0xa3/0x170
[  137.426616]  ? lru_add_drain+0x11/0x20
[  137.427058]  ? free_pages_and_swap_cache+0xa6/0x120
[  137.427672]  ? tlb_flush_mmu_free+0x78/0x90
[  137.428168]  ? arch_tlb_finish_mmu+0x6d/0xb0
[  137.428680]  __vfs_write+0xc4/0x350
[  137.430917]  ? kernel_read+0xa0/0xa0
[  137.432758]  ? remove_vma+0x90/0x90
[  137.434781]  ? __kasan_slab_free+0x14b/0x180
[  137.437486]  ? remove_vma+0x83/0x90
[  137.439836]  ? kmem_cache_free+0x78/0x1e0
[  137.442195]  ? percpu_counter_add_batch+0x1d/0x90
[  137.444389]  vfs_write+0xf7/0x280
[  137.446030]  SyS_write+0xa1/0x120
[  137.447867]  ? SyS_read+0x120/0x120
[  137.449670]  ? mm_fault_error+0x180/0x180
[  137.451539]  ? _cond_resched+0x16/0x50
[  137.453697]  ? SyS_read+0x120/0x120
[  137.455883]  do_syscall_64+0xeb/0x250
[  137.457686]  entry_SYSCALL_64_after_hwframe+0x21/0x86
[  137.459595] RIP: 0033:0x7fb415637b94
[  137.461315] RSP: 002b:00007ffdebea7d88 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[  137.463879] RAX: ffffffffffffffda RBX: 00005565022d1bd0 RCX: 00007fb415637b94
[  137.466519] RDX: 0000000000000018 RSI: 00007ffdebea7da0 RDI: 0000000000000003
[  137.469543] RBP: 00007ffdebea7d98 R08: 0000000000000000 R09: 00005565022d40c0
[  137.472479] R10: 00000000000009cf R11: 0000000000000246 R12: 00005565022d2520
[  137.475125] R13: 00000000000003e8 R14: 0000000000000000 R15: 00007ffdebea7fd0
[  137.477760] Code: f7 e8 dd 0d 0b ff 48 c7 43 40 00 00 00 00 48 89 df e8 0d 0b 0b ff 48 8d 7b 28 c6 03 00 e8 41 0d 0b ff 48 8b 7b 28 48 85 ff 74 06 <f0> ff 4f 48 74 10 5b 48 89 ef 5d 41 5c 41 5d 41 5e e9 32 b0 ee
[  137.483375] RIP: rdma_restrack_del+0xc8/0xf0 RSP: ffff8801b54e7968
[  137.486436] ---[ end trace 81835a1ea6722eed ]---
[  137.488566] Kernel panic - not syncing: Fatal exception
[  137.491162] Kernel Offset: 0x36000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)

Fixes: 00313983 ("RDMA/nldev: provide detailed CM_ID information")
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

As a default, for Ethernet packets, the device scatters only the payload
of ingress packets. The scatter FCS feature lets the user to get the FCS
(Ethernet's frame check sequence) in the received WR's buffer as a 4
Bytes trailer following the packet's payload.
Reviewed-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NGuy Levi <guyle@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Report to the user area the TSO device capabilities, it includes the
max_tso size and the QP types that support it.

The TSO is applicable only when when of the ports is ETH and the device
supports it.

uresp logic around rss_caps is updated to fix a till-now harmless bug
computing the length of the structure to copy. The code did not handle the
implicit padding before rss_caps correctly. This is necessay to copy
tss_caps successfully.
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NYishai Hadas <yishaih@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

There is no explicit tear-down sequence initiated on
connections if the Control QP OP, Modify QP to close,
fails. Fix this by triggering a driver generated
Asynchronous Event (AE) on Modify QP failures and
tear-down the connection on receipt of the AE.

This fix can be generalized to other Modify QP failures
(i.e. RTS->TERM, IDLE->RTS, etc) as any modify failure
will require a connection tear-down.

Fixes: d3749841 ("i40iw: add files for iwarp interface")
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The flush CQP OP can be used to optionally generate
Asynchronous Events (AEs) in addition to QP flush.
Consolidate all HW AE generation code under a new
function i40iw_gen_ae which use the flush CQP OP
to only generate AEs.
Signed-off-by: NHenry Orosco <henry.orosco@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Open coding a loose value is not acceptable for describing the uABI in
RDMA. Provide the missing struct.
Reviewed-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Open coding a loose value is not acceptable for describing the uABI in
RDMA. Provide the missing struct.
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

All of these defines are part of the uABI for the driver, this
header duplicates providers/i40iw/i40iw-abi.h in rdma-core.
Acked-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

MLX4_USER_DEV_CAP_LARGE_CQE (via mlx4_ib_alloc_ucontext_resp.dev_caps)
and MLX4_IB_QUERY_DEV_RESP_MASK_CORE_CLOCK_OFFSET (via
mlx4_uverbs_ex_query_device_resp.comp_mask) are copied directly to
userspace and form part of the uAPI.

Move them to the uapi header where they belong.
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Open coding pointer math is not acceptable for describing the uABI in
RDMA. Provide structs for all the cases.

The udata is casted to the struct as close to the verbs entry point
as possible for maximum clarity. Function signatures and so forth
are revised to allow for this.
Tested-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

It isn't used and it couldn't possibly ever be used correctly.
Tested-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

rvt_mregion uses percpu_ref for reference counting and RCU to protect
accesses from lkey_table.  When a rvt_mregion needs to be freed, it
first gets unregistered from lkey_table and then rvt_check_refs() is
called to wait for in-flight usages before the rvt_mregion is freed.

rvt_check_refs() seems to have a couple issues.

* It has a fast exit path which tests percpu_ref_is_zero().  However,
  a percpu_ref reading zero doesn't mean that the object can be
  released.  In fact, the ->release() callback might not even have
  started executing yet.  Proceeding with freeing can lead to
  use-after-free.

* lkey_table is RCU protected but there is no RCU grace period in the
  free path.  percpu_ref uses RCU internally but it's sched-RCU whose
  grace periods are different from regular RCU.  Also, it generally
  isn't a good idea to depend on internal behaviors like this.

To address the above issues, this patch removes the fast exit and adds
an explicit synchronize_rcu().
Signed-off-by: NTejun Heo <tj@kernel.org>
Acked-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: linux-rdma@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Code includes wmb() followed by writel() in multiple places. writel()
already has a barrier on some architectures like arm64.

This ends up CPU observing two barriers back to back before executing the
register write.

Since code already has an explicit barrier call, changing writel() to
writel_relaxed().
Signed-off-by: NSinan Kaya <okaya@codeaurora.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

This patch changes the type of cqn from u32 to u64 to keep
userspace and kernel consistent, initializes resp both for
cq and qp to zeros, and also changes the condition judgment
of outlen considering future caps extension.
Suggested-by: NJason Gunthorpe <jgg@mellanox.com>
Fixes: e088a685 (hns: Support rq record doorbell for the user space)
Fixes: 9b44703d (hns: Support cq record doorbell for the user space)
Signed-off-by: NYixian Liu <liuyixian@huawei.com>
Signed-off-by: NLijun Ou <oulijun@huawei.com>
Signed-off-by: NWei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: NShaobo Xu <xushaobo2@huawei.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Before commit [1], rdma_addr_find_l2_eth_by_grh() was an exported function
and therefore declaration in include/rdma/ib_addr.h was fine.

But now that its scope is limited to ib_core module, its better to have it
in core_priv.h.

[1] commit 1060f865 ("IB/{core/cm}: Fix generating a return AH for
RoCEE")
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Introduce and use helper function get_cm_port_from_path() to get
cm_port based on the the path record entry.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Resolving route for RoCE for a path record is needed only for the
received CM requests.
Therefore,
(a) ib_init_ah_attr_from_path() is refactored first to isolate the
code of resolving route.
(b) Setting dlid, path bits is not needed for RoCE.

Additionally ah attribute initialization is done from the path record
entry, so it is better to refer to path record entry type for
different link layer instead of ah attribute type while initializing
ah attribute itself.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Add and use helper function add_cm_id_to_port_list() to attach
cm_id to port list.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

add_gid() and del_gid() are optional callback routines.
ib_core ignores invoking them while updating GID table entries if
they are not implemented by provider drivers. Therefore remove them.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

rdma_resolve_ip_route() is used only by ib_core module. Therefore it is
removed as an exported symbol.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

rdma_protocol_roce() API from the ib_core already provides a way to
detect whether a given device+port is RoCE or not.
Therefore, make use of it and avoid implementing it again in rdmacm
module.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

ah_attr contains the port number to which cm_id is bound. However, while
searching for GID table for matching GID entry, the port number is
ignored.

This could cause the wrong GID to be used when the ah_attr is converted to
an AH.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The return status of ib_init_ah_from_mcmember() is ignored by
cma_ib_mc_handler().  Honor it and return error event if ah attribute
initialization failed.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

ib_find_gid() is only used by IPoIB driver. For IB link layer, GID table
entries are not based on netdevice. Netdevice parameter is unused here.
Therefore, it is removed.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

Exported symbol's comments should be with function definition and not in
the header file. Therefore comments of ib_find_cached_gid() and
ib_find_cached_gid_by_port() functions are moved closer to their
definitions.

The function name in then comment is different than the actual function
name, fix it to be same as ib_cache_gid_find_by_filter().

Also current comment section of ib_find_cached_gid_by_port() contains the
desciption of ib_find_cached_gid(), fix that as well.
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NJason Gunthorpe <jgg@mellanox.com>

The failure to destroy the MRs is printed on mlx5_core layer
as error and it makes warning prints useless.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

"live" is needed for ODP only and is better to be guarded
by appropriate CONFIG.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

According to the IBTA spec 1.3, the driver failure in
MR reregister shall release old and new MRs.

 C11-20: If the CI returns any other error, the CI shall
 invalidate both "old" and "new" registrations, and release
 any associated resources.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Return -EOPNOTSUPP value to the user for unsupported reg_user_mr.
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The mlx5_ib_alloc_implicit_mr() can fail to acquire pages
and the returned mr pointer won't be valid. Ensure that it
is not error prior to access.

Cc: <stable@vger.kernel.org> # 4.10
Fixes: 81713d37 ("IB/mlx5: Add implicit MR support")
Reported-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch.  This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.

Conflicts:
	drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f
	(IB/mlx5: Fix cleanup order on unload) added to for-rc and
	commit b5ca15ad (IB/mlx5: Add proper representors support)
	add as part of the devel cycle both needed to modify the
	init/de-init functions used by mlx5.  To support the new
	representors, the new functions added by the cleanup patch
	needed to be made non-static, and the init/de-init list
	added by the representors patch needed to be modified to
	match the init/de-init list changes made by the cleanup
	patch.
Updates:
	drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
	prototypes added by representors patch to reflect new function
	names as changed by cleanup patch
	drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
	stage list to match new order from cleanup patch
Signed-off-by: NDoug Ledford <dledford@redhat.com>