The chunks are stored inside a parameter structure in the kernel
and when we copy them to the user, we need to account for
the parameter header.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope.  This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

 ipv6.c     |   12 ++++++------
 protocol.c |   12 ++++++------
 2 files changed, 12 insertions(+), 12 deletions(-)

sctp_assoc_change notification may contain the data from a received
ABORT chunk.  Set the length correctly to account for that.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

To make sure the procfs visibility occurs after the ->proc_fs ops are
setup, use proc_net_fops_create() and proc_net_remove().

This also fixes an OOPS after module unload in that the name string
for remove was wrong, so it wouldn't actually be removed.  That bug
was introduced by commit 61145aa1
("[KEY]: Clean up proc files creation a bit.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is used in connector.c only, so make it static.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bug did bite at least one user, who did have to resort to rebooting
the system after an "ifconfig eth0 127.0.0.1" typo.

Deleting the address and adding a new is a less intrusive workaround.
But I still beleive this is a bug that should be fixed.  Some way or
another.

Another possibility would be to remove the scope mangling based on
address.  This will always be incomplete (are 127/8 the only address
space with host scope requirements?)

We set the scope to RT_SCOPE_HOST if an IPv4 interface is configured
with a loopback address (127/8).  The scope is never reset, and will
remain set to RT_SCOPE_HOST after changing the address. This patch
resets the scope if the address is changed again, to restore normal
functionality.
Signed-off-by: NBjorn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some more missing initializations of the new nl_info.nl_net field
in IPv6 stack. This field will be used when network namespaces are
fully supported.
Signed-off-by: NBenjamin Thery <benjamin.thery@bull.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete a possibly armed timer before kfree'ing the connection object.

Solves: http://lkml.org/lkml/2008/2/15/514Reported-by: NQuel Qun <kelk1@comcast.net>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/tipc/cluster.c:145:2: warning: Using plain integer as NULL pointer
net/tipc/link.c:3254:36: warning: Using plain integer as NULL pointer
net/tipc/ref.c:151:15: warning: Using plain integer as NULL pointer
net/tipc/zone.c:85:2: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Don't require platform code to be #ifdeffed according to whether
I2C is enabled or not ... if it's not enabled, let GCC compile out
all I2C device declarations.  (Issue noted on an NSLU2 build that
didn't configure I2C.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Commit 8b798c4d broke
alchemy build, fix it.  Pointed out by Adrian Bunk.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.

[JD: Some more fixes.]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMike Rapoport <mike@compulab.co.il>
Tested-by: NEric Miao <ymiao3@marvell.com>

Each call to i2c_get_adapter() must be followed by a call to
i2c_put_adapter() to release the grabbed reference. Otherwise the
reference count grows forever and the adapter can never be
unregistered.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NVladimir Ananiev <vovan888@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata-core: fix kernel-doc warning
  sata_fsl: fix build with ATA_VERBOSE_DEBUG
  [libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
  libata-pmp: clear hob for pmp register accesses
  libata: automatically use DMADIR if drive/bridge requires it
  power_state: get rid of write-only variable in SATA
  pata_atiixp: Use 255 sector limit

Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:

  CC      drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

SB700 SATA controller can support 64 bit DMA, the previous commit
badc2341 was added with
careless reference to SB600, which should be modified by this patch.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.

> >>> And the behaviour I see is very bizarre.

>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...

This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.

Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).

One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Acked-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.

That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).

So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.

This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.

Original patch is from Mark Lord.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

AHCI needs sorting too but this deals with the old interface
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix some spelling errors and inconsistencies in comment blocks.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix NCFGR.SPD setting on 10Mbps.  This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix problems in LED management, so ethtool -p works correctly on Yukon-EC
and other chips. The driver was incorrectly setting the PHY LED overide bits.
Moral: read the spec sheet, not the vendor driver.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use register offset definition for WOLcgClr, rather than a magic
number.

This patch does not change the driver behaviour.
Signed-off-by: NLaura Garcia Liebana <nevola@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
  [NETFILTER]: fix ebtable targets return
  [IP_TUNNEL]: Don't limit the number of tunnels with generic name explicitly.
  [NET]: Restore sanity wrt. print_mac().
  [NEIGH]: Fix race between neighbor lookup and table's hash_rnd update.
  [RTNL]: Validate hardware and broadcast address attribute for RTM_NEWLINK
  tg3: ethtool phys_id default
  [BNX2]: Update version to 1.7.4.
  [BNX2]: Disable parallel detect on an HP blade.
  [BNX2]: More 5706S link down workaround.
  ssb: Fix support for PCI devices behind a SSB->PCI bridge
  zd1211rw: fix sparse warnings
  rtl818x: fix sparse warnings
  ssb: Fix pcicore cardbus mode
  ssb: Make the GPIO API reentrancy safe
  ssb: Fix the GPIO API
  ssb: Fix watchdog access for devices without a chipcommon
  ssb: Fix serial console on new bcm47xx devices
  ath5k: Fix build warnings on some 64-bit platforms.
  WDEV, ath5k, don't return int from bool function
  WDEV: ath5k, fix lock imbalance
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: make IOMMU code respect the segment boundary limits
  [SPARC64]: Fix cpu trampoline et al. mismatch warnings.
  [SPARC64]: More sparse warning fixes in process.c
  [SPARC64]: Fix sparse warning wrt. fault_in_user_windows.
  [SPARC64]: Kill show_regs32().
  [SPARC64]: Fix sparse warnings wrt. __show_regs().
  [SPARC64]: Kill show_stackframe{,32}().
  [SPARC64]: Fix sparse warnings wrt. machine_alt_power_off().

This patch fixes a check-after-use spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>