Joe Perches pointed out that we were inconsistent in the use of
PF vs pf or VF vs vf in our driver code.  Since acronyms are usually
capitalized to denote that it is an acronym, changed all references to
be consistent throughout the code.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The NVMUpdate tool doesn't necessarily know the ReadOnly map of the current
NVM image, and must try reading and writing words that may be protected.
This generates an error out of the Firmware request that the driver logs.
Unfortunately, this ends up spitting out hundreds of bogus read and write
error message that looks rather messy.

This patch checks the error type and under normal conditions will not print
the typical read and write errors during NVMUpdate.  This can be overridden
by enabling the NVM update debugging.  This results in a much less messy log
file, and likely many fewer customer support questions.

Change-ID: Id4ff2e9048c523b0ff503aa5ab181b025ec948ea
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix a bug introduced in the force writeback code, where the interrupt
rate was set to 0 (maximum) by accident.

The driver must correctly set the NOITR fields to avoid ITR update
as a side effect of triggering the software interrupt.

Change-ID: I290851ae04ef3811c43aab5ee33242029f26c1a3
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a reset occurs when the netdev is closed, the reset task will hang in
napi_disable, causing deadlocks and general grumpiness.

Check to make sure the device is actually running before stopping
everything. This allows the reset task to complete and have a real good
time.

Change-ID: Iaaea84acbcb9b3810c216b14c3326e4287b75b58
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure the sizeof() calls are taking the size of the actual struct
that we care about.  By using the pointer variable, we'll always get
the right struct size, even if the variable type changes sometime in
the future.

Change-ID: Id5858f883cf42447365ea3733080d7714f975bce
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While using the Linux "strings" command I found these two strings in the
driver.  There's no need for them and they're kinda silly.

Change-ID: I4e19b02983d48b631e9a9979f49790492845f221
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add missing "cdns,at91sam9260-macb", "atmel,sama5d3-gem" and
"atmel,sama5d4-gem" compatible strings.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.

$ git ls-files drivers/net/ethernet/ | \
  while read file ; do \
    codespell -w $file; \
  done

I removed a false positive in e1000_hw.h
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not having a reset control line to the ethernet controller should not be a
hard failure. Instead, add support for deferred probing and just print out
a debug statement.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric W. Biederman says:

====================
mpls: Minor fixes and cleanups

This is a bunch of small changes that have come out of the discussions
of the mpls code and the automated tests that people run against things.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a little bit of unnecessary work when transmitting a packet with
neigh_packet_xmit.  Use the neighbour table index not the address family
as a parameter.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the OPENVSWITCH Kconfig option and old Kconfigs by having
OPENVSWITCH select both NET_MPLS_GSO and MPLSO.

A Kbuild test robot reported that when NET_MPLS_GSO is selected by
OPENVSWITCH the generated .config is broken because MPLS is not
selected.

Cc: Simon Horman <horms@verge.net.au>
Fixes: cec9166c mpls: Refactor how the mpls module is built
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to RFC3032 section 2.4.2  packets with an outgoing
ttl of 0 MUST NOT be forwarded.  According to section 2.4.1
an outgoing TTL of 0 comes from an incomming TTL <= 1.

Therefore any packets that is received with a ttl <= 1 should
not have it's ttl decremented and forwarded.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sparse was generating a lot of warnings mostly from missing annotations
in the code.  Add missing annotations and in a few cases tweak the code
for performance by moving work before loops.

This also fixes a problematic ommision of rcu_assign_pointer and
rcu_dereference.

Hopefully with complete rcu annotations any new rcu errors will stick
out like a sore thumb.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

*Blink* I got the argument order wrong to kzalloc and the
code was working properly when tested. *Blink*

Fix that.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove reference to obsolete ifconfig command.
MTU can be changed with ip command instead.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-03-07

This series contains updates to i40e and i40evf only.

Most notably, Greg provides the patch to remove the dreaded configfs
changes in the driver.

Shannon cleans up a sparse warning by simply straighting out the code
so it is less convoluted.  Fixes an issue where the vector allocation
was trying too hard to save vectors for VMDq, to the point of not giving
the PF enough when in a tight situation, such as an NPAR partition.
Changed the driver to make sure that the PF will get all the queues and
vectors it wants to fill out its destiny.  Cleans up reporting to only
print the port and VEB stats if it is the first partition of a
multiplexed port.

Catherine cleans up some duplicated code by simply removing the duplicate
code.

Kamil cleans up the driver by removing an un-needed endian conversion
because it is already done by a register read function.

Jesse fixes a variable width of a datatype, where a u16 should have been
a u32.  Also cleans up debug_read_register() to resolve some sparse
warnings.  Updates the driver to use prefetch() to get the next Tx
descriptor, like in ixgbe, to improve performance.

Akeem moves around code to enable/disable loopback so that other non-SRIOV
supported driver functions can take advantage of the changes.

Anjali cleans up the logging for adding/deleting FD-SB filters, since
ethtool shows all the filters on an interface.  Updates the driver to
use l4_tunnel type generically to keep code flow simple.  Simplifies
the RSS code since the driver initializes the rss_size_max in sw_init.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable EEE support for MV88E6352.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EEE configuration is similar for the various MV88E6xxx chips.
Add generic support for it.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for supporting multiple Rx queues:
1. Move the initialization of priv->num_rx_bds, priv->rx_bds, and
   priv->rx_cbs from bcmgenet_init_rx_ring() to bcmgenet_init_dma()
   since they are not specific to a single Rx queue. Mimics the Tx
   init model where priv->num_tx_bds, priv->tx_bds, and priv->tx_cbs
   are initialized in bcmgenet_init_dma().
2. Program DMA_MBUF_DONE_THRESH = 1 so that future Rx queues Q0-Q15
   will get per-packet Rx interrupt.
3. Group DMA_START_ADDR, RDMA_READ_PTR, RDMA_WRITE_PTR, and DMA_END_ADDR
   initialization together. Mimics the Tx init model.
4. There is 1-to-1 mapping between RxCBs and RxBDs.
   Precalculate RxCB->bd_addr so that it can be used in the future.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'macb-next'

Boris Brezillon says:

====================
net/macb: merge at91_ether driver into macb driver

The rm9200 boards use the dedicated at91_ether driver instead of the
regular macb driver.

Both the macb and at91_ether drivers can be compiled as separated
modules.
Since the at91_ether driver uses code from the macb driver, at91_ether.ko
depends on macb.ko.

However the macb.ko module always fails to load on rm9200 boards: the
macb_probe() function expects a hclk clock which doesn't exist on rm9200.
Then the at91_ether.ko can't be loaded in turn due to unresolved
dependencies.

This series of patches fix this issue by merging at91_ether into macb.

Patch 1 is fixing a problem that might happen when enabling ARM
multi-platform suppot.

Changes since v3:
- move "net: macb: remove #if defined(CONFIG_ARCH_AT91) sections" patch
  into this series to avoid dependency on other patch series.

Changes since v2:
- rebase after changed brought by commit "net: macb: remove #if
  defined(CONFIG_ARCH_AT91) sections"

Changes since v1:
- rework probe functions to share common probing logic
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macb and at91_ether drivers can be compiled as modules, but the at91_ether
driver use some functions and variables defined in the macb one, thus
creating a dependency on the macb driver.

Since these drivers are sharing the same logic we can easily merge
at91_ether into macb.

In order to factorize common probing logic we've added an ->init() function
to struct macb_config (the structure associated with the compatible
string), and moved macb specific init code from macb_probe to macb_init.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the functions from the Common Clk Framework handle NULL pointer as
input argument.

Since the TX clock is optional, we now set tx_clk to NULL value
instead of ERR_PTR(-ENOENT) when this clock is not available. This simplifies
the clock management and avoid the need to test tx_clk value.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With multi platform support those sections could lead to unexpected
behavior if both ARCH_AT91 and another ARM SoC using the MACB IP are
selected.
Add two new capabilities to encode the default MII mode and the presence
of a CLKEN bit in USRIO register.
Then define the appropriate config for IPs embedded in at91 SoCs.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some at91 SoCs embed a 10/100 Mbit Ethernet IP, that is based on the
at91sam9260 SoC.
Fix at91 DTs accordingly.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of configfs is not allowed in network drivers.  Strip the code that
uses it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.12 and i40evf to 1.2.6.

Change-ID: I641871da3a9abd396b28eda5744a4d68493c1400
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Performance can be improved a bit by imitating ixgbe and using
prefetch to get us the next Tx descriptor.

Change-ID: Ice7ffd4cd0ce87c35295059bdb7972a7f53723aa
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We initialize the pf->rss_size_max in sw_init now
and hence this code can be simplified.

Change-ID: I1a7abc837604a40bc65e6c6b21190b909ed6bb21
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use l4_tunnel type generically to keep code flow simple.

Change-ID: Ic52287e3b1ca4204e6b6e13431890c1a6ae9c422
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since GLQF_FDCNT_0 register now has the right offset, use it to simplify our
FD flush flow.
If the filter add error happens to be for SB we just auto disable SB.

If filter error happens to be for ATR, auto disable ATR and mark
the state to FD_FLUSH_REQUESTED. Which gets cleared when flush completes.

If we are entering flush too quickly (< 30 seconds) and we have quite
a few SB rules, its time to disable ATR for good. Since SB + ATR rules
is most likely making the FD table unstable.

ATR can be re-enabled by turning ntuple off (ethtool -K ntuple off)
and will remain off after turning ntuple on till it gets unstable again.

Change-ID: I2154a2e0a5d44851a2f0eb8731e2f1d4a4d1acbc
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It is not necessary to print FD filter add/delete log with
normal debug settings because ethtool -n ethx shows all the FD-SB
filters on an interface. The log can still be turned on through higher
debug levels and it will continue to print a log if there was an error
in the add/delete process.

Change-ID: I67db2baf49e2075d2f537de40f7895e5b02cd610
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only print the port and veb stats if this is the first partition
of a multiplexed port.

Change-ID: I7ce0c323cdee5cfd2e54d8bea5b0b9102987e671
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since changes made to enable or disable loopback for all VSIs, not only SR-IOV
or PCIOV, then it became necessary to move the associated functions to main
file - so that other non-SRIOV supported driver can take advantage of the
changes.

Change-ID: I59a49fd23a6136acda5e16f8d1e5ac7fd9c5fc05
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The initial problem solved here is that the vector allocation was trying
too hard to save vectors for VMDq, to the point of not giving the PF enough
when in a tight situation such as an NPAR partition.  This change makes
sure that the PF will get all the queues and vectors it wants to fill
out its destiny.  Essentially, nothing is specially reserved for VMDq,
it simply gets whatever is left after the PF, FCoE, and FD sideband get
what they want.

Additionally, the calculations for the reservations were harder to follow
than necessary, so I've made it more straight forward.

Change-ID: I99b384f104535b686c690b8ef0a787559485c8d4
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There were some additional spaces and strange (double swapping) logic
in this function that I started looking at because sparse was warning.

This fixes the sparse warning and fixes up the other issues.

Change-ID: I72a91a4197cd45921602649040e6bd25e5f17c0a
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel returns a u32 for netif_msg_init, and we were storing
it in a u16.  Fix the width of the datatype.

Change-ID: I4b23326e5707c91cd59325c5a1ccb2ba7a3974fc
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove LE16 to CPU endianes conversion from i40e_read_nvm_word_srctl
function, as it's already done by register read function.

Change-ID: I739f0f20a9b8e18223e54c0ca5443e63d75da878
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This series of code was repeated twice, remove one of them.
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>