If there was a dss device without a driver and thus omapfb probe failed,
ref counts could be left to dss devices.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

If driver's probe failed, the uninit was not called.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The system to allow panel drivers to exists as attached to ctrl drivers
did never work very well. It is not useed, and this patch removes it to
make the driver cleaner.

For now, controller drivers need to include also the panel driver code. In
the future a proper mechanism for this should be developed, perhaps by
creating busses for controllers.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

When OMAP PM layer is no-op/debug, the PM layer will increment context
loss count with every call. This resulted DSS2 to restore context
whenever a clock was enabled.

This commit checks the context loss count only when the context actually
could have been lost, ie. when enabling a clock when no clocks had been
previously enabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

It was not used.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Instead of configuring only VC0 to be usable, configure all four VCs
similarly. This is needed to utilize the other VCs.

Setting the FIFO sizes evenly for all VCs, regardless of how many VCs are
actually used, is not optimal. However, this affects only cases when
larger amounts of data are written or read via L4, meaning that normal use
cases are not affected.

At some point this could be optimized better to suit different use cases.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Rename and export dsi_vc_enable_hs() so that the display drivers can
control the mode of the DSI link.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add helper functions for most common DCS read and write operations.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Helper function to clean up the checking of the bus lock.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

dss_select_clk_source() was rather confusing. Selecting the source with
enums is much clearer.

The clk source selection is also stored into memory, so that we know what
is the selected source, even when clocks are off. This is important during
setup, as we need to what clocks to turn on before the clocks are turned
on.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Fix compilation of the CONFIG_OMAP2_DSS_COLLECT_IRQ_STATS feature.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Previously the only place to get the size of the display was from the
DSS's sysfs interface, making, for example, configuring overlays and doing
updates on manual displays more difficult.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The workqueue creation error branch attempted to destroy a NULL wq,
and, in turn, a failed registration does not destroy the newly created
workqueue.

The problem was reported by a static analysis tool.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

The regulator is now enabled by DSS driver, and thus the panel driver
doesn't need to touch it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

It looks like on OMAP3 some DSS pins need VDDS_DSI to function properly.

This has not been confirmed from TI, but looking at figure 15-1 "Display
subsystem highlight" from the TRM, some data pins come near the DSI and SDI
blocks. This is not very hard evidence, but the fact remains that with the
power on, pixels are ok, and with the power off, pixels are not ok.

It may also be that VDDS_SDI is needed to power some pins, but as normally
both VDDS_SDI and VDDS_DSI come from the same power source, this hasn't
been shown.

It seems that a single driver can only get a regulator once. This patch
solves it by getting all the required regulators in one place, and from
which the submodules then get the regulators they need.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add support of TPO TD043MTEA1 TFT LCD panel to DSS2 driver.
This panel is used by OMAP3 Pandora device.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

If the panel's probe had failed, omapfb would still go on, eventually
crashing.

A better fix would be to handle each display properly, and leaving just
the failed display out. But that is a bigger change.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.
Signed-off-by: NVille Syrjälä <ville.syrjala@nokia.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Loops checking for certain condition were rather inconsistent.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: NJuha Leppanen <juha_motorsportcom@luukku.com>

Fixes bug causing VRFB memory area to be released twice.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
Reported-by: NEino-Ville Talvala <talvala@stanford.edu>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

DSI driver didn't check if the panel driver actually implements
enable_te().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Collect interrupt statistics, printable via debugfs:

debugfs/omapdss/dispc_irq
debugfs/omapdss/dsi_irq

The counters are reset when printed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

- dsi_vc_send_short() needs to use dest_per for the peripheral id
- dsi_vc_send_null() was always using channel id 0
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add Generic panel (user for DVI output) and Sharp LS037V7DW01 LCD panel.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

DSI (Display Serial Interface) driver implements MIPI DSI interface.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

SDI (Serial Display Interface) implements TI Flatlink 3G display
interface.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

RFBI (Remote FrameBuffer Interface) implements MIPI DBI interface.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

VENC (video encoder) driver implements OMAP's analog S-Video/Composite
TV-out.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>

This implements MIPI DPI interface.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

This file implements DISPC (display controller) block of the OMAP DSS.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Add more core files to DSS2.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>