Most board-*.c files read configuration data from the bootloader in
their .init_machine() function.  This needs to happen earlier, at some
point before omap2_init_common_hw() is called.  This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

After a hardware module's clocks are enabled, Linux must wait for it
to indicate readiness via its IDLEST bit before attempting to access
the device, otherwise register accesses to the device may trigger an
abort.  This has traditionally been implemented in the clock
framework, but this is the wrong place for it: the clock framework
doesn't know which module clocks must be enabled for a module to leave
idle; and if a module is not in smart-idle mode, it may never leave
idle at all.  This type of information is best stored in a
per-hardware module data structure (coming in a following patch),
rather than a per-clock data structure.  The new code will use these new
functions to handle waiting for modules to enable.

Once hardware module data is filled in for all of the on-chip devices,
the clock framework code to handle IDLEST waiting can be removed.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The interface provides device drivers, CPUFreq, and DSPBridge with a
means of controlling OMAP power management parameters that are not yet
supported by the Linux PM PMQoS interface.  Copious documentation is
in the patch in Documentation/arm/OMAP/omap_pm and the interface
header file, arch/arm/plat-omap/include/mach/omap-pm.h.

Thanks to Rajendra Nayak <rnayak@ti.com> for adding CORE (VDD2) OPP
support and moving the OPP table initialization earlier in the event
that the clock code needs them.  Thanks to Tero Kristo
<tero.kristo@nokia.com> for fixing the parameter check in
omap_pm_set_min_bus_tput().  Jouni signed off on Tero's patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NJouni Högander <jouni.hogander@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Igor Stoppa <igor.stoppa@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Anand Sawant <sawant@ti.com>
Cc: Sakari Poussa <sakari.poussa@nokia.com>
Cc: Veeramanikandan Raju <veera@ti.com>
Cc: Karthik Dasu <karthik-dp@ti.com>

omap2_init_clk_clkdm() is called as part of the chip architecture-specific
initialization code, so calling it again from the struct clk init pointer
just wastes cycles.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

All MPU-related clocks should be in the mpu_clkdm.  This is needed for the
upcoming omap_hwmod patches, which needs to know the clockdomain that arm_fck
is in.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The argument 'mpurate' had no effect on the MPU
frequency. This patch fixes the same.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add missing SDRC register offset macros.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added commit message]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

At the end of the list pd is a pointer to a NULL struct, so checking
if the address == NULL doesn't help here. In fact the original code
will just keep running past the struct to read who knows what in
memory.

This case manifests itself when from clkdms_setup() when enabling auto
idle for a clock domain and the clockdomain usecount is greater than
0. When _clkdm_add_autodeps() tries to add the a dependency that does
not exist in the powerdomain->wkdep_srcs array the for loop will run
past the wkdep_srcs array.

Currently in linux-omap you won't hit this because the not found case
is never executed, unless you start modifying powerdomains and their
wakeup/sleep deps.
Signed-off-by: NMike Chan <mike@android.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Update the OMAP3 Beagle defconfig to add EHCI, MMC, TWL4030 GPIO support.
Beagle can again use MMC rootfs after this patch.  Tested on BeagleBoard
rev C2.

Patch updated to enable PM and OTG options as suggested by
Eric Witcher <ewitcher@mindspring.com>.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

without it twl4030_usb driver will not probe.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update defconfig for Zoom2 to include
TWL4030 core
TWL4030 drivers (bci, gpio, keypad, usb, mmc)

Also sync the defconfig after issuing a menuconfig
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add TWL4030 CORE and TWL4030 drivers to Zoom2 board file
TWL drivers enabled are:
	bci
	madc
	usb
	keypad
	mmc
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For OMAP3 add MMC1 MMC2 pin mux MMC3 mux is not added as there are
multiple configurations possible, so the muxing is left to be done
in board file.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NChikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

twl4030 watchdog will be compiled as a module by default.
Signed-off-by: NAtal Shargorodsky <ext-atal.shargorodsky@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch makes the SDP boot again with the defconfig.

Changes done:

 - Removes other selected boards.
 - Sets the Low Level debug output for UART1.
 - Disables some paripherals from other boards.

Tested on a SDP3430-VE5.1.0 (OMAP3430 ES3.1)
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Pass irqflags to 8250 driver with platform_data. At least Zoom2 has
IRQF_TRIGGER_RISING requirement for the 8250 GPIO irq.

This patch is dependent on 8250 driver changes getting accepted upstream:
http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=commit;h=7053133124d5cdf207c1168c7a0c582a18e12ea7Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This enables to peek the following data.

$ /debug/iommu/isp# ls
mem             nr_tlb_entries  regs
mmap            pagetable       tlb
$ /debug/iommu/isp# head pagetable
L:      da:      pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The second argument should be the end address, not the
length. Actually there will not be any effect on the behavior of this
driver since flush_cache_vmap() calls flush_cache_all() in the end.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add defconfig file for OMAP2 N800 and N810 devices.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board file for Nokia N800 and N810 devices. Currently only serial ports,
onenand and spi are configured, more to come later.

Tested on Nokia N800.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For some reason usb-tusb6010.c was't compiled, add it to Makefile and
Kconfig. This is prepraration for upcoming n8x0 support.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for modem device found on Amstrad E3 (Delta) board.

Based on earlier patch by Jonathan McDowell, available at
http://the.earth.li/pub/e3/2.6.19/ams-delta-modem.patch.
Modified after Ladislav Michl's arch/arm/mach-omap1/board-voiceblue.c.

This patch is dependent on 8250 driver changes getting accepted upstream:
http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=commit;h=7053133124d5cdf207c1168c7a0c582a18e12ea7Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It is possible for GPIO IRQ lines configured with
falling edge triggering only to get IRQs at the
rising edge upon the exit of offmode. And vice
versa. Prevent such IRQs to arrive by generating
the IRQ obeying the detection scheme.
Signed-off-by: NEero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove left over code for parsing omap boot tags. This is
no longer used.
see commit fc0ef1bfa1353e048e055374a09c75320d22231b
Signed-off-by: NRoger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP tags are deprecrated so drop them.

Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.

Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.)  After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Omap tags are deprecated and remove OMAP_TAG_SERIAL_CONSOLE. Console must be
enabled with the console boot parameter instead.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove ifdefs for io.h
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rename OMAP_MPUIO_BASE to OMAP1_MPUIO_BASE
Signed-off-by: NTony Lindgren <tony@atomide.com>

Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.

Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.

In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>

The root cause is a duplicate section name (.text); is this legal?
[ Amerigo Wang: "AFAIK, yes." ]

However, there's a problem with commit
6d760133 in that if you fail to allocate
a mod->sect_attrs (in this case it's null because of the duplication),
it still gets used without checking in add_notes_attrs()

This should fix it

[ This patch leaves other problems, particularly the sections directory,
  but recent parisc toolchains seem to produce these modules and this
  prevents a crash and is a minimal change -- RR ]
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Tested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The rarely-used symbol_put_addr() needs to use dereference_function_descriptor
on powerpc.
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.

Connect to the backend before registering our framebuffer with the kernel.

[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  inotify: Ensure we alwasy write the terminating NULL.
  inotify: fix locking around inotify watching in the idr
  inotify: do not BUG on idr entries at inotify destruction
  inotify: seperate new watch creation updating existing watches

We call lmb_end_of_DRAM() to test whether a DMA mask is ok on a machine
without IOMMU, but this function is marked as __init.

I don't think there's a clean way to get the top of RAM max_pfn doesn't
appear to include highmem or I missed (or we have a bug :-) so for now,
let's just avoid having a broken 2.6.31 by making this function
non-__init and we can revisit later.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: update documentation pointers
  9p: remove unnecessary v9fses->options which duplicates the mount string
  net/9p: insulate the client against an invalid error code sent by a 9p server
  9p: Add missing cast for the error return value in v9fs_get_inode
  9p: Remove redundant inode uid/gid assignment
  9p: Fix possible regressions when ->get_sb fails.
  9p: Fix v9fs show_options
  9p: Fix possible memleak in v9fs_inode_from fid.
  9p: minor comment fixes
  9p: Fix possible inode leak in v9fs_get_inode.
  9p: Check for error in return value of v9fs_fid_add

Add a check in ip_append_data() for NULL *rtp to prevent future bugs in
callers from being exploitable.
Signed-off-by: NJulien Tinnes <julien@cr0.org>
Signed-off-by: NTavis Ormandy <taviso@sdf.lonestar.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kAFS crashes when asked to read a symbolic link because page_getlink()
passes a NULL file pointer to read_mapping_page(), but afs_readpage()
expects a file pointer from which to extract a key.

Modify afs_readpage() to request the appropriate key from the calling
process's keyrings if a file struct is not supplied with one attached.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before the rewrite copy_event_to_user always wrote a terqminating '\0'
byte to user space after the filename.  Since the rewrite that
terminating byte was skipped if your filename is exactly a multiple of
event_size.  Ouch!

So add one byte to name_size before we round up and use clear_user to
set userspace to zero like /dev/zero does instead of copying the
strange nul_inotify_event.  I can't quite convince myself len_to_zero
will never exceed 16 and even if it doesn't clear_user should be more
efficient and a more accurate reflection of what the code is trying to
do.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NEric Paris <eparis@redhat.com>

The are races around the idr storage of inotify watches.  It's possible
that a watch could be found from sys_inotify_rm_watch() in the idr, but it
could be removed from the idr before that code does it's removal.  Move the
locking and the refcnt'ing so that these have to happen atomically.
Signed-off-by: NEric Paris <eparis@redhat.com>