Fix Section mismatch warinig in adf_exit_vf_wq()
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

IRQs need to be enabled when VFs go down in case some VF to PF
comms happens.
Tested-by: NSuman Bangalore Sathyanarayana <sumanx.bangalore.sathyanarayana@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Before VF sends a signal to PF it should check if PF
is still running.
Tested-by: NSuman Bangalore Sathyanarayana <sumanx.bangalore.sathyanarayana@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The vf2pf_init and vf2pf_exit are exactly the same for all VFs
so move them to common and reuse.
Tested-by: NSuman Bangalore Sathyanarayana <sumanx.bangalore.sathyanarayana@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.

lzo_init uses __GFP_REPEAT to allocate LZO1X_MEM_COMPRESS 16K. This is
order 3 allocation request and __GFP_REPEAT is ignored for this size
as well as all <= PAGE_ALLOC_COSTLY requests.

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: NMichal Hocko <mhocko@suse.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This adds the Hisilicon Random Number Generator(RNG) support,
which is found in Hip04 and Hip05 soc.
Reviewed-by: NMathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Document the devicetree bindings for the random number generator found
on Hisilicon Hip04 and Hip05 soc.
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: NRob Herring <rob@kernel.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

According to the Freescale GPL driver code, there are two different
Security Controller (SCC) versions: SCC and SCC2.

The SCC is found on older i.MX SoCs, e.g. the i.MX25. This is the
version implemented and tested here.

As there is no publicly available documentation for this IP core,
all information about this unit is gathered from the GPL'ed driver
from Freescale.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add the Security Controller (SCC) module to the dtsi.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add documentation for the Freescale Security Controller (SCC)
found on i.MX25 SoCs.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

VFs call adf_dev_stop() from a PF to VF interrupt bottom half.
This causes an oops "scheduling while atomic", because it tries
to acquire a mutex to un-register crypto algorithms.
This patch fixes the issue by calling adf_dev_stop() asynchronously.

Changes in v2:
 - change kthread to a work queue.
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Direct include of rwlock_types.h breaks RT, use spinlock_types.h instead.

Fixes: 553d2374 crypto: ccp - Support for multiple CCPs
Signed-off-by: NMike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NEric Biggers <ebiggers3@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Correct smasung.com into samsung.com.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

It returns always zero anyway.
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

When stopping devices it is not enought to loop backwards.
We need to explicitly stop all VFs first.
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The HMAC implementation allows setting the HMAC key independently from
the hashing operation. Therefore, the key only needs to be set when a
new key is generated.

This patch increases the speed of the HMAC DRBG by at least 35% depending
on the use case.

The patch is fully CAVS tested.
Signed-off-by: NStephan Mueller <smueller@chronox.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The current sun4i-ss driver could generate data corruption when ciphering/deciphering.
It occurs randomly on end of handled data.
No root cause have been found and the only way to remove it is to replace
all spin_lock_bh by their irq counterparts.

Fixes: 6298e948 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: NLABBE Corentin <clabbe.montjoie@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NTudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

memcopying to a (null pointer + offset) will result
in memory corruption or undefined behaviour.
Signed-off-by: NTudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Remove redundant nrbg rings.
Signed-off-by: NAhsan Atta <ahsan.atta@intel.com>
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

FW requires the const_tab to be 1024 bytes aligned.
Signed-off-by: NTadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Within the copying loop in mpi_read_raw_from_sgl(), the last input SGE's
byte count gets artificially extended as follows:

  if (sg_is_last(sg) && (len % BYTES_PER_MPI_LIMB))
    len += BYTES_PER_MPI_LIMB - (len % BYTES_PER_MPI_LIMB);

Within the following byte copying loop, this causes reads beyond that
SGE's allocated buffer:

  BUG: KASAN: slab-out-of-bounds in mpi_read_raw_from_sgl+0x331/0x650
                                     at addr ffff8801e168d4d8
  Read of size 1 by task systemd-udevd/721
  [...]
  Call Trace:
   [<ffffffff818c4d35>] dump_stack+0xbc/0x117
   [<ffffffff818c4c79>] ? _atomic_dec_and_lock+0x169/0x169
   [<ffffffff814af5d1>] ? print_section+0x61/0xb0
   [<ffffffff814b1109>] print_trailer+0x179/0x2c0
   [<ffffffff814bc524>] object_err+0x34/0x40
   [<ffffffff814bfdc7>] kasan_report_error+0x307/0x8c0
   [<ffffffff814bf315>] ? kasan_unpoison_shadow+0x35/0x50
   [<ffffffff814bf38e>] ? kasan_kmalloc+0x5e/0x70
   [<ffffffff814c0ad1>] kasan_report+0x71/0xa0
   [<ffffffff81938171>] ? mpi_read_raw_from_sgl+0x331/0x650
   [<ffffffff814bf1a6>] __asan_load1+0x46/0x50
   [<ffffffff81938171>] mpi_read_raw_from_sgl+0x331/0x650
   [<ffffffff817f41b6>] rsa_verify+0x106/0x260
   [<ffffffff817f40b0>] ? rsa_set_pub_key+0xf0/0xf0
   [<ffffffff818edc79>] ? sg_init_table+0x29/0x50
   [<ffffffff817f4d22>] ? pkcs1pad_sg_set_buf+0xb2/0x2e0
   [<ffffffff817f5b74>] pkcs1pad_verify+0x1f4/0x2b0
   [<ffffffff81831057>] public_key_verify_signature+0x3a7/0x5e0
   [<ffffffff81830cb0>] ? public_key_describe+0x80/0x80
   [<ffffffff817830f0>] ? keyring_search_aux+0x150/0x150
   [<ffffffff818334a4>] ? x509_request_asymmetric_key+0x114/0x370
   [<ffffffff814b83f0>] ? kfree+0x220/0x370
   [<ffffffff818312c2>] public_key_verify_signature_2+0x32/0x50
   [<ffffffff81830b5c>] verify_signature+0x7c/0xb0
   [<ffffffff81835d0c>] pkcs7_validate_trust+0x42c/0x5f0
   [<ffffffff813c391a>] system_verify_data+0xca/0x170
   [<ffffffff813c3850>] ? top_trace_array+0x9b/0x9b
   [<ffffffff81510b29>] ? __vfs_read+0x279/0x3d0
   [<ffffffff8129372f>] mod_verify_sig+0x1ff/0x290
  [...]

The exact purpose of the len extension isn't clear to me, but due to
its form, I suspect that it's a leftover somehow accounting for leading
zero bytes within the most significant output limb.

Note however that without that len adjustement, the total number of bytes
ever processed by the inner loop equals nbytes and thus, the last output
limb gets written at this point. Thus the net effect of the len adjustement
cited above is just to keep the inner loop running for some more
iterations, namely < BYTES_PER_MPI_LIMB ones, reading some extra bytes from
beyond the last SGE's buffer and discarding them afterwards.

Fix this issue by purging the extension of len beyond the last input SGE's
buffer length.

Fixes: 2d4d1eea ("lib/mpi: Add mpi sgl helpers")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Within the byte reading loop in mpi_read_raw_sgl(), there are two
housekeeping indices used, z and x.

At all times, the index z represents the number of output bytes covered
by the input SGEs for which processing has completed so far. This includes
any leading zero bytes within the most significant limb.

The index x changes its meaning after the first outer loop's iteration
though: while processing the first input SGE, it represents

  "number of leading zero bytes in most significant output limb" +
   "current position within current SGE"

For the remaining SGEs OTOH, x corresponds just to

  "current position within current SGE"

After all, it is only the sum of z and x that has any meaning for the
output buffer and thus, the

  "number of leading zero bytes in most significant output limb"

part can be moved away from x into z from the beginning, opening up the
opportunity for cleaner code.

Before the outer loop iterating over the SGEs, don't initialize z with
zero, but with the number of leading zero bytes in the most significant
output limb. For the inner loop iterating over a single SGE's bytes,
get rid of the buf_shift offset to x' bounds and let x run from zero to
sg->length - 1.
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The number of bits, nbits, is calculated in mpi_read_raw_from_sgl() as
follows:

  nbits = nbytes * 8;

Afterwards, the number of leading zero bits of the first byte get
subtracted:

  nbits -= count_leading_zeros(*(u8 *)(sg_virt(sgl) + lzeros));

However, count_leading_zeros() takes an unsigned long and thus,
the u8 gets promoted to an unsigned long.

Thus, the above doesn't subtract the number of leading zeros in the most
significant nonzero input byte from nbits, but the number of leading
zeros of the most significant nonzero input byte promoted to unsigned long,
i.e. BITS_PER_LONG - 8 too many.

Fix this by subtracting

  count_leading_zeros(...) - (BITS_PER_LONG - 8)

from nbits only.

Fixes: 2d4d1eea ("lib/mpi: Add mpi sgl helpers")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

In mpi_read_raw_from_sgl(), unsigned nbits is calculated as follows:

  nbits = nbytes * 8;

and redundantly cleared later on if nbytes == 0:

  if (nbytes > 0)
    ...
  else
    nbits = 0;

Purge this redundant clearing for the sake of clarity.
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

At the very beginning of mpi_read_raw_from_sgl(), the leading zeros of
the input scatterlist are counted:

  lzeros = 0;
  for_each_sg(sgl, sg, ents, i) {
    ...
    if (/* sg contains nonzero bytes */)
      break;

    /* sg contains nothing but zeros here */
    ents--;
    lzeros = 0;
  }

Later on, the total number of trailing nonzero bytes is calculated by
subtracting the number of leading zero bytes from the total number of input
bytes:

  nbytes -= lzeros;

However, since lzeros gets reset to zero for each completely zero leading
sg in the loop above, it doesn't include those.

Besides wasting resources by allocating a too large output buffer,
this mistake propagates into the calculation of x, the number of
leading zeros within the most significant output limb:

  x = BYTES_PER_MPI_LIMB - nbytes % BYTES_PER_MPI_LIMB;

What's more, the low order bytes of the output, equal in number to the
extra bytes in nbytes, are left uninitialized.

Fix this by adjusting nbytes for each completely zero leading scatterlist
entry.

Fixes: 2d4d1eea ("lib/mpi: Add mpi sgl helpers")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Currently, the nbytes local variable is calculated from the len argument
as follows:

  ... mpi_read_raw_from_sgl(..., unsigned int len)
  {
    unsigned nbytes;
    ...
    if (!ents)
      nbytes = 0;
    else
      nbytes = len - lzeros;
    ...
  }

Given that nbytes is derived from len in a trivial way and that the len
argument is shadowed by a local len variable in several loops, this is just
confusing.

Rename the len argument to nbytes and get rid of the nbytes local variable.
Do the nbytes calculation in place.
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Currently, mpi_read_buffer() writes full limbs to the output buffer
and moves memory around to purge leading zero limbs afterwards.

However, with

  commit 9cbe21d8 ("lib/mpi: only require buffers as big as needed for
                        the integer")

the caller is only required to provide a buffer large enough to hold the
result without the leading zeros.

This might result in a buffer overflow for small MP numbers with leading
zeros.

Fix this by coping the result to its final destination within the output
buffer and not copying the leading zeros at all.

Fixes: 9cbe21d8 ("lib/mpi: only require buffers as big as needed for
                      the integer")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Currently, the endian conversion from CPU order to BE is open coded in
mpi_read_buffer().

Replace this by the centrally provided cpu_to_be*() macros.
Copy from the temporary storage on stack to the destination buffer
by means of memcpy().
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Currently, if the number of leading zeros is greater than fits into a
complete limb, mpi_read_buffer() skips them by iterating over them
limb-wise.

Instead of skipping the high order zero limbs within the loop as shown
above, adjust the copying loop's bounds.
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Currently, the endian conversion from CPU order to BE is open coded in
mpi_write_sgl().

Replace this by the centrally provided cpu_to_be*() macros.
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Within the copying loop in mpi_write_sgl(), we have

  if (lzeros) {
    mpi_limb_t *limb1 = (void *)p - sizeof(alimb);
    mpi_limb_t *limb2 = (void *)p - sizeof(alimb)
                               + lzeros;
    *limb1 = *limb2;
    ...
  }

where p points past the end of alimb2 which lives on the stack and contains
the current limb in BE order.

The purpose of the above is to shift the non-zero bytes of alimb2 to its
beginning in memory, i.e. to skip its leading zero bytes.

However, limb2 points somewhere into the middle of alimb2 and thus, reading
*limb2 pulls in lzero bytes from somewhere.

Indeed, KASAN splats:

  BUG: KASAN: stack-out-of-bounds in mpi_write_to_sgl+0x4e3/0x6f0
                                      at addr ffff8800cb04f601
  Read of size 8 by task systemd-udevd/391
  page:ffffea00032c13c0 count:0 mapcount:0 mapping:   (null) index:0x0
  flags: 0x3fff8000000000()
  page dumped because: kasan: bad access detected
  CPU: 3 PID: 391 Comm: systemd-udevd Tainted: G  B  L
                                              4.5.0-next-20160316+ #12
  [...]
  Call Trace:
   [<ffffffff8194889e>] dump_stack+0xdc/0x15e
   [<ffffffff819487c2>] ? _atomic_dec_and_lock+0xa2/0xa2
   [<ffffffff814892b5>] ? __dump_page+0x185/0x330
   [<ffffffff8150ffd6>] kasan_report_error+0x5e6/0x8b0
   [<ffffffff814724cd>] ? kzfree+0x2d/0x40
   [<ffffffff819c5bce>] ? mpi_free_limb_space+0xe/0x20
   [<ffffffff819c469e>] ? mpi_powm+0x37e/0x16f0
   [<ffffffff815109f1>] kasan_report+0x71/0xa0
   [<ffffffff819c0353>] ? mpi_write_to_sgl+0x4e3/0x6f0
   [<ffffffff8150ed34>] __asan_load8+0x64/0x70
   [<ffffffff819c0353>] mpi_write_to_sgl+0x4e3/0x6f0
   [<ffffffff819bfe70>] ? mpi_set_buffer+0x620/0x620
   [<ffffffff819c0e6f>] ? mpi_cmp+0xbf/0x180
   [<ffffffff8186e282>] rsa_verify+0x202/0x260

What's more, since lzeros can be anything from 1 to sizeof(mpi_limb_t)-1,
the above will cause unaligned accesses which is bad on non-x86 archs.

Fix the issue, by preparing the starting point p for the upcoming copy
operation instead of shifting the source memory, i.e. alimb2.

Fixes: 2d4d1eea ("lib/mpi: Add mpi sgl helpers")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Within the copying loop in mpi_write_sgl(), we have

  if (lzeros) {
    ...
    p -= lzeros;
    y = lzeros;
  }
  p = p - (sizeof(alimb) - y);

If lzeros == 0, then y == 0, too. Thus, lzeros gets subtracted and added
back again to p.

Purge this redundancy.
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Within the copying loop in mpi_write_sgl(), we have

  if (lzeros > 0) {
    ...
    lzeros -= sizeof(alimb);
  }

However, at this point, lzeros < sizeof(alimb) holds. Make this fact
explicit by rewriting the above to

  if (lzeros) {
    ...
    lzeros = 0;
  }
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Currently, if the number of leading zeros is greater than fits into a
complete limb, mpi_write_sgl() skips them by iterating over them limb-wise.

However, it fails to adjust its internal leading zeros tracking variable,
lzeros, accordingly: it does a

  p -= sizeof(alimb);
  continue;

which should really have been a

  lzeros -= sizeof(alimb);
  continue;

Since lzeros never decreases if its initial value >= sizeof(alimb), nothing
gets copied by mpi_write_sgl() in that case.

Instead of skipping the high order zero limbs within the loop as shown
above, fix the issue by adjusting the copying loop's bounds.

Fixes: 2d4d1eea ("lib/mpi: Add mpi sgl helpers")
Signed-off-by: NNicolai Stange <nicstange@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Sort the headers alphabetically to improve readability and to spot
duplications easier.
Suggested-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

During crypto selftests on Odroid XU3 (Exynos5422) some of the
algorithms failed because of passing AES-block unaligned source and
destination buffers:

alg: skcipher: encryption failed on chunk test 1 for ecb-aes-s5p: ret=22

Handle such case by copying the buffers to a new aligned and contiguous
space.
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Remove unneeded inclusion of delay.h and get rid of indentation from
labels.
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Gary will be taking over future development of the CCP driver, so add
him as a co-maintainer of the driver.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Acked-by: NGary Hook <gary.hook@amd.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>