Use USEC_PER_SEC instead of 1000000, that making the later bugfix
more clearly.
Signed-off-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Lots of style fixes for the IPMI system interface driver.  No functional
changes.  Basically fixes everything reported by checkpatch and fixes the
comment style.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Rocky Craig <rocky.craig@hp.com>
Cc: Hannes Schulz <schulz@schwaar.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The IPMI BT subdriver has been patched to survive "long busy" timeouts seen
during firmware upgrades and resets.  The patch never returns the HOSED state,
synthesizes response messages with meaningful completion codes, and recovers
gracefully when the hardware finishes the long busy.  The subdriver now issues
a "Get BT Capabilities" command and properly uses those results.  More
informative completion codes are returned on error from transaction starts;
this logic was propogated to the KCS and SMIC subdrivers.  Finally, indent and
other style quirks were normalized.
Signed-off-by: NRocky Craig <rocky.craig@hp.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make SMIC driver ignore EVT_AVAIL and SMS_ATN bits in flags register, as
they're used by systems management interrupts, not the host OS.

Make the OEM0 Data Available handler work for pre-IPMI 1.5 systems from Dell
too.

Without these two fixes, PowerEdge 2650 and other similar systems with SMIC
may hang a process (modprobe or anything using /dev/ipmi0).
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

A number of small changes for the various system interface drivers,
consolidated from a number of patches from Matt Domsch.

Clear B2H_ATN and drain the BMC message buffer on command timeout.  This
prevents further commands from failing after a timeout.

Add bt_debug and smic_debug module parameters, expose them in sysfs.  This
lets you enable and disable debugging messages at runtime.

Unsigned jiffies math in ipmi_si_intf.c causes a too-large value to be passed
to ->event() after jiffies wrap-around.  The BT driver had caught this, but
didn't know how to fix it.  Now all calls to ->event() use a sane value for
time.

Increase timeout for commands handed to the BT driver from 2 seconds to 5
seconds.  This is necessary particularly when the previous command was a
"Clear SEL", as that command completes, yet the BMC isn't really ready to
handle another command yet.

Silence BT debugging messages which were being printed on the console.

Increase SMIC timeout form 1/10s to 2s.  This is needed on Dell PowerEdge 2650
and PowerEdge 750 with ERA/O cards to allow commands to complete without
timing out.

Adds kcs_debug module param, to match behavior of BT and SMIC.  This also
prevents messages from being sent to the console unless explicitly requested.
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This adds MODULE_VERSION, MODULE_DESCRIPTION, and MODULE_AUTHOR tags to the
IPMI driver modules.  Also changes the MODULE_VERSION to remove the
prepended 'v' on each value, consistent with the module versioning policy.

This patch also removes all the version information from everything except
the ipmi_msghandler module.
Signed-off-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!