Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: NTobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The check for a one byte message should be msg[0] == 0x55 not msg == 0x55
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add several missing messages from SPI3, SPI4 and SPI5:
 - Terminate Process
 - Continue Task
 - Target Transfer Disable
 - Clear ACA
 - LUN Reset
 - ACA
 - QAS Request
Rename some older commands to their SPI5 names:
 - Command Complete -> Task Complete
 - Abort -> Abort Task Set
 - Bus device Reset -> Target Reset
 - Clear Queue -> Clear Task Set

Change spi_print_msg() to always consume one byte, even if we don't
recognise it.  That allows drivers to call it in a loop to print all
messages.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fix a bug where we would consume one byte too many in the message
printing code.
Add support for 256-byte long messages.
Add support for the Modify Bidirectional Data Pointer message.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Almost all the output from spi_print_msg() has a trailing space.
This patch fixes up the three cases that don't.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Introduce new helpers:
 - spi_populate_width_msg()
 - spi_populate_sync_msg()
 - spi_populate_ppr_msg()

and use them in drivers which already enable the SPI transport.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

show_spi_transport_period_helper() doesn't need the class_device parameter
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Change the core SCSI code to use kzalloc rather than kmalloc+memset
where possible.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Introduce a new helper, print_nego() to handle SDTR/WDTR/PPR.
Split out the guts of show_spi_transport_period_helper() into period_to_str()
and use it in print_nego to get the period factor conversion right.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Replace the custom NO_*_MSGS definitions with uses of ARRAY_SIZE.
This fixes a bug in the definition of NO_EXTENDED_MSGS.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

A missing comma meant that "Ordered Queue Tag" and "Ignore Wide Residue"
were being concatenated together.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

scsi_print_msg() is an SPI-specific concept.  This patch moves it from
constants.c to scsi_transport_spi.c and updates the Kconfig to link in
the SPI class for the drivers which use scsi_print_msg().
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

None of the other domain validation messages have a trailing full stop,
so I don't see why this one should.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Some SCSI devices apparently get very confused if we try to use the
echo buffer on a non-DT negotiated bus (this mirrors the problems of
using PPR on non-LVD for some devices).  The fix is to be far more
conservative about when we use an echo buffer.  With this patch, we'll
now see what parameters are negotiated by the read only test, and only
look for an echo buffer if DT is negotiated.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables.  As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This one's slightly more difficult.  The transport class uses
REQ_FAILFAST, so another interface (scsi_execute) had to be invented to
take the extra flag.  Also, the sense functions are shifted around to
allow spi_execute to place data directly into a struct scsi_sense_hdr.
With this change, there's probably a lot of unnecessary sense buffer
allocation going on which we can fix later.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

I recently tried to construct a totally generic transport class and
found there were certain features missing from the current abstract
transport class.  Most notable is that you have to hang the data on the
class_device but most of the API is framed in terms of the generic
device, not the class_device.

These changes are two fold

- Provide the class_device to all of the setup and configure APIs
- Provide and extra API to take the device and the attribute class and
  return the corresponding class_device
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch is necessary if we begin exposing underlying physical disks
(which can attach to the SPI transport class) of the hardware RAID
cards, since we don't want any SPI parameters binding to the RAID
devices.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant.  However,
just in case anyone should want to do this, it's appropriate to include
the parameter.

I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.

I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

At the moment, the transport class blindly tries to set things like
QAS and IU, even if the drive won't support them.  It's best not to
annoy the devices like this and instead only set what the drive says
is actually supported.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are several extra things that have to be considered when running
Domain Validation on a u320 target (notably how you fall back).

Hopefully this should help us when someone adds this transport class to
aic79xx.

I've tested this on the lsi1030, so I know it works correctly up to
u320.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There's a basic need not to have parameters go under or over certain
values when doing domain validation.  The basic ones are

max_offset, max_width and min_period

This patch makes the transport class take and enforce these three
limits.  Currently they can be set by the user, although they could
obviously be read from the HBA's on-board NVRAM area during
slave_configure (if it has one).
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The premise is that domain validation is likely to trigger errors which
it wants to know about, so the only time it should be retrying them is
when it gets a unit attention (likely as the result of a previous bus or
device reset).  Ironically, the previous coding retried three times in
all cases except those of unit attention.  The attached fixes this to do
the right thing.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!