Fix runtime warning with backtrace from hostap by removing
netif_stop_queue() call before register_netdev. Tested to work fine on
hostap_pci Prism 2.5.

(This removes a warning about calling netif_stop_queue before
register_netdev is called. -- JWL)
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.

To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone().  For the rt2800pci special case a driver
flag is introduced.

https://bugzilla.kernel.org/show_bug.cgi?id=24892Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NEduardo Costa <ecosta.tmp@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On suspend, there might be usb wireless drivers which wrongly trigger
the warning in ieee80211_work_work. If an usb driver doesn't have a
suspend hook, the usb stack will disconnect the device. On disconnect,
a mac80211 driver calls ieee80211_unregister_hw, which calls dev_close,
which calls ieee80211_stop, and in the end calls ieee80211_work_purge->
ieee80211_work_work.

The problem is that this call to ieee80211_work_purge comes after
mac80211 is suspended, triggering the warning even when we don't have
work queued in work_list (the expected case when already suspended),
because it always calls ieee80211_work_work.

So, just call ieee80211_work_work in ieee80211_work_purge if we really
have to abort work. This addresses the warning reported at
https://bugzilla.kernel.org/show_bug.cgi?id=24402Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds five more USBIDs to the table.

Source:
http://www.linuxant.com/pipermail/driverloader/2005q3/002307.html
http://wireless.kernel.org/en/users/Drivers/p54/devices (by M. Davis)

Cc: <stable@kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dev_open will eventually call ieee80211_ibss_join which sets up the
skb used for beacons/probe-responses however it is possible to
receive beacons that attempt to merge before this occurs causing
a null pointer dereference.  Check ssid_len as that is the last
thing set in ieee80211_ibss_join.

This occurs quite easily in the presence of adhoc nodes with hidden SSID's

revised previous patch to check further up based on irc feedback
Signed-off-by: NTim Harvey <harvey.tim@gmail.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code wants to check if there's a channel and it is not disabled,
but it used to check if channel is not NULL and accessed the channel
struct if this check failed.
Signed-off-by: NSven Neumann <s.neumann@raumfeld.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

From: Johannes Berg <johannes.berg@intel.com>

The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.

However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.

This bug causes the response of the system to certain attacks to be
ineffective.

It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.

wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.

The log tends to look like:

State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.

Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

... and interface up.

In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.

Clear the setting so that the reporting matches what the driver has
done..

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 doesn't handle shared skbs correctly at the moment. As a result
a possible resize can trigger a BUG in pskb_expand_head.

[  676.030000] Kernel bug detected[#1]:
[  676.030000] Cpu 0
[  676.030000] $ 0   : 00000000 00000000 819662ff 00000002
[  676.030000] $ 4   : 81966200 00000020 00000000 00000020
[  676.030000] $ 8   : 819662e0 800043c0 00000002 00020000
[  676.030000] $12   : 3b9aca00 00000000 00000000 00470000
[  676.030000] $16   : 80ea2000 00000000 00000000 00000000
[  676.030000] $20   : 818aa200 80ea2018 80ea2000 00000008
[  676.030000] $24   : 00000002 800ace5c
[  676.030000] $28   : 8199a000 8199bd20 81938f88 80f180d4
[  676.030000] Hi    : 0000026e
[  676.030000] Lo    : 0000757e
[  676.030000] epc   : 801245e4 pskb_expand_head+0x44/0x1d8
[  676.030000]     Not tainted
[  676.030000] ra    : 80f180d4 ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] Status: 1000a403    KERNEL EXL IE
[  676.030000] Cause : 10800024
[  676.030000] PrId  : 0001964c (MIPS 24Kc)
[  676.030000] Modules linked in: mac80211_hwsim rt2800lib rt2x00soc rt2x00pci rt2x00lib mac80211 crc_itu_t crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc [last unloaded: rt2800pci]
[  676.030000] Process kpktgend_0 (pid: 97, threadinfo=8199a000, task=81879f48, tls=00000000)
[  676.030000] Stack : ffffffff 00000000 00000000 00000014 00000004 80ea2000 00000000 00000000
[  676.030000]         818aa200 80f180d4 ffffffff 0000000a 81879f78 81879f48 81879f48 00000018
[  676.030000]         81966246 80ea2000 818432e0 80f1a420 80203050 81814d98 00000001 81879f48
[  676.030000]         81879f48 00000018 81966246 818432e0 0000001a 8199bdd4 0000001c 80f1b72c
[  676.030000]         80203020 8001292c 80ef4aa2 7f10b55d 801ab5b8 81879f48 00000188 80005c90
[  676.030000]         ...
[  676.030000] Call Trace:
[  676.030000] [<801245e4>] pskb_expand_head+0x44/0x1d8
[  676.030000] [<80f180d4>] ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] [<80f1a420>] ieee80211_xmit+0x150/0x22c [mac80211]
[  676.030000] [<80f1b72c>] ieee80211_subif_start_xmit+0x6f4/0x73c [mac80211]
[  676.030000] [<8014361c>] pktgen_thread_worker+0xfac/0x16f8
[  676.030000] [<8002ebe8>] kthread+0x7c/0x88
[  676.030000] [<80008e0c>] kernel_thread_helper+0x10/0x18
[  676.030000]
[  676.030000]
[  676.030000] Code: 24020001  10620005  2502001f <0200000d> 0804917a  00000000  2502001f  00441023  00531021

Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.

Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.

It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.
Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the oops below when attempting to bring up a mesh
interface on ath5k hardware.

[  128.933099] kernel BUG at drivers/net/wireless/ath/ath5k/base.c:197!
[  128.933099] invalid opcode: 0000 [#1]
(...)
[  128.933099] Call Trace:
[  128.933099]  [<c83b77fa>] ? ath5k_beacon_update+0x57/0x1f8 [ath5k]
[  128.933099]  [<c02d9a40>] ? __sysfs_add_one+0x28/0x76
[  128.933099]  [<c83b830e>] ? ath5k_bss_info_changed+0x13f/0x173
[ath5k]
[  128.933099]  [<c82ff629>] ? ieee80211_config_beacon+0xc0/0x17e
[mac80211]
[  128.933099]  [<c82f073e>] ?
ieee80211_bss_info_change_notify+0x182/0x18b [mac80211]
[  128.933099]  [<c83b81cf>] ? ath5k_bss_info_changed+0x0/0x173 [ath5k]
[  128.933099]  [<c82ff6d6>] ? ieee80211_config_beacon+0x16d/0x17e
[mac80211]
[  128.933099]  [<c82ff753>] ? ieee80211_add_beacon+0x34/0x39 [mac80211]
[  128.933099]  [<c830a4ed>] ? ieee80211s_init+0xf8/0x10f [mac80211]
[  128.933099]  [<c830a5df>] ? ieee80211_mesh_init_sdata+0xdb/0x154 [mac80211]
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The interrupt handler takes a lock - but since commit bcad6e80 this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.

Fix orinoco_cs and spectrum_cs

<https://bugzilla.kernel.org/show_bug.cgi?id=23932>

Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If we fail to find a hci device pointer in hci_uart, don't try
to deref the NULL one we do have.
Signed-off-by: NJun Nie <njun@marvell.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.

This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.

Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.

Able to pass Wifi Test case 5.2.18 with this fix.

Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.

Cc: stable@kernel.org
Signed-off-by: NMatteo Croce <matteo@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to commit 63ce0900 connections initiated through TTYs created with
"rfcomm bind ..." would have security level BT_SECURITY_SDP instead of
BT_SECURITY_LOW. This would cause instant connection failure between any
two SSP capable devices due to the L2CAP connect request to RFCOMM being
sent before authentication has been performed. This patch fixes the
regression by always initializing the DLC security level to
BT_SECURITY_LOW.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NLuiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This reverts commit 916448e7.

"As far as I can tell, either of these patches breaks multiple VIF
scenarios.  I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
  -- Ben Greear <greearb@candelatech.com>

http://marc.info/?l=linux-wireless&m=129123368719339&w=2Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.

Cc:stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.
Signed-off-by: NBala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)
Signed-off-by: NStefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.

Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.

Able to pass Wifi Test case 5.2.18 with this fix.

Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.

This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.

Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes an curious issue due to insufficient
rx frame filtering.

Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]

The reason is that the device generates frames with slightly
bogus SA/TA addresses.

e.g.:
 [ 2314.402316] Ignore 9f:1f:31:f8:64:ff
 [ 2314.402321] Ignore 9f:1f:31:f8:64:ff
 [ 2352.453804] Ignore 0d:1f:31:f8:64:ff
 [ 2352.453808] Ignore 0d:1f:31:f8:64:ff
 					   ^^ the group-address flag is set!
 (the correct SA/TA would be: 00:1f:31:f8:64:ff)

Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!

This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.

Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: NSaqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the problem causing the following trace:

------------[ cut here ]------------
WARNING: at linux-2.6.34/net/wireless/core.c:633 wdev_cleanup_work+0xb7/0xe0 [cfg80211]()
Hardware name: Latitude C840
Pid: 707, comm: cfg80211 Not tainted 2.6.34.7-0.5-desktop #1
Call Trace:
 [<c02065c3>] try_stack_unwind+0x173/0x190
 [<c02051cf>] dump_trace+0x3f/0xe0
 [<c020662b>] show_trace_log_lvl+0x4b/0x60
 [<c0206658>] show_trace+0x18/0x20
 [<c064e0b3>] dump_stack+0x6d/0x72
 [<c02443ae>] warn_slowpath_common+0x6e/0xb0
 [<c0244403>] warn_slowpath_null+0x13/0x20
 [<e2db5497>] wdev_cleanup_work+0xb7/0xe0 [cfg80211]
 [<c025cfa9>] run_workqueue+0x79/0x170
 [<c025d123>] worker_thread+0x83/0xe0
 [<c025fef4>] kthread+0x74/0x80
 [<c0203826>] kernel_thread_helper+0x6/0x10
---[ end trace 3f0348b3b0c6f4ff ]---

Reported by: Giacomo Comes <comes@naic.edu>
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit: "carl9170: revamp carl9170_tx_prepare"
introduced a peculiar bug that would only show
up if the the module parameter noht is set to 1.

Then all outbound voice, video and background
frames would each invoke a (bogus) RTS/CTS
handshake.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order for frame injection to work properly for some use cases
(e.g., finding the station entry and keys for encryption), mac80211
needs to find the correct sdata entry. This works when the main vif
is in AP mode, but commit a2c1e3da
broke this particular use case for station main vif. While this type of
injection is quite unusual operation, it has some uses and we should fix
it. Do this by changing the monitor vif sdata selection to allow station
vif to be selected instead of limiting it to just AP vifs. We still need
to skip some iftypes to avoid selecting unsuitable vif for injection.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With some upcoming changes we'd like to use
the interface types for P2P capability tests.
Enable them now so that when we add those
tests in wpa_supplicant, nothing will break.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:

WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18

---[ end trace 5345fc6f870564a6 ]---

This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>