Enable Micrel KS8851 SPI network chip for OMAP4430
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Change dependency to ARCH_OMAP2PLUS to allow systems based on
omap24xx, omap34xx or omap44xx

Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: NSyed Rafiuddin <rafiuddin.syed@ti.com>
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There is two gpio for mmc use, one is for card detecting, another is
used for checking write protect. Intialize its pinmux in case the bootloader
doesn't set it.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Multi line comments are fixed as per CodingStyle
guidelines.

Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NManjunatha GK <manjugk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If we are softbooting another kernel using kexec, DMA controller state is not
known when we are performing omap_init_dma(). It is possible that some DMA
channels are already active. For example after kexec we get:

<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5

To prevent any weird things happening, we disable all channel interrupts during
init.
Signed-off-by: NMika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The SDI Display subsystem needs access to the vdds_sdi supply
regulator. This is TWL4030's VAUX1 supply on RX-51.
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>

Merge branch 'pm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus

Merge branch 'gpio-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus

The patch adds a CONFIG directive required for supporting the Amstrad Delta
connected external keyboard by default.

Created and tested against linux-omap master,
commit 104a77440f05430f29f9d3f4ecb88c1536819585 dated 2010-04-27.

Works on top of PATCH v4 4/5(7), "input: serio: add support for Amstrad Delta
serial keyboard port".
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

EHCI port on UI card and LCD share two pins (GPIO 181 and 182) thus
they have to be mutually exclusive.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Upcoming change to tlv320aic3x codec driver require four supplies.
Implement this by connecting analogic supplies to TWL4030 VMMC2 and digital
supplies to TWL4030 VIO.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This makes possible to probe the audio codec and add another i2c2
components in the future.

Fix also indentation for the first omap_register_i2c_bus.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

I believe the VMMC2 constraints must be the same than with VAUX3. Older
boards are using TWL4030 VMMC2 supply for internal MMC whereas newer are
using VAUX3 that has more limited constraints defined in this same file.

More over, the VMMC2 supply is used also for analog audio domain and the
miminum analog voltage of the TLV320AIC34 codec is 2.7 V.

To combine these two facts, the patch changes supply name to V28_A as the
newer boards register VMMC2_30 for VAUX3 and uses the same constraints than
VAUX3 since those constraints are ok for the TLV320AIC34.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Some Overo add-on boards include a second ethernet port.  This patch
adds support for that second port.
Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update the default configuration for AM3517EVM to enable
support for EMAC peripheral.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The emac driver currently uses Davinci clock names for the module and phy
clocks. Updated the omap3xxx_clks table to match the names
used by the Davinci emac driver.

Note that eventually the EMAC clocks should be renamed to be generic.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated patch description to match the patch]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Modified AM35xx EVM init sequence to handle EMAC
initialization.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define offsets for EMAC sub modules.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Modify the default kernel configuration on AM3517 to enable CAN.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board specific hookup for TI HECC driver on
AM3517 EVM
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the new default configuration for the Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize multiplexed pins with correct mode.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Configuration for OMAP2430 should select ARCH_OMAP_OTG just like
it is done for OMAP2420
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for OHCI USB on OMAP2430 SDP
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
[tony@atomide.com: Updated subject to mention the board name]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize isp1301 FS USB transceiver and
add I2C bus1 initialization code for OMAP2430 SDP
Signed-off-by: NViral Mehta <viral.mehta@lntinfotech.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The patch provides the following ams_delta_defconfig updates:
- explicitly select preemptable RCU,
- replace outdated CONFIG_LBD and CONFIG_LSF options with CONFIG_LBDAF,
- activate support for LCD contrast setting (new in 2.6.34),
- turn off verbose bug reporting for smaller kernel.

Created and tested against linux-2.6.34-rc3.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This rejects unaligned device virtual address('da') and physical
address('pa') and informs error to caller when a page table entry is
set. Otherwise, a wrong address can be used by IO device.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Hari Kanigeri <h-kanigeri2@ti.com>

Searching avaialable spaces should be stopped as soon as it turns out
that there's no possibility with the rest of it.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

Inserting a gap page between IOVMAs could detect an override on other
IOVMA with iommu fault. This was originally suggested by Sakari Ailus
and based on the work and comment by David Cohen.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: David Cohen <david.cohen@nokia.com>
Cc: Sakari Ailus <Sakari.Ailus@nokia.com>

This CONFIG_OMAP_IOMMU_DEBUG option cannot be selected because it's
not visible on menu. Make this option selectable.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

There are some places to scan iotlb entries. This iteration macro
could make these code a bit simpler with proceeding iotlb entries
transparently.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Tested-by: NHari Kanigeri <h-kanigeri2@ti.com>

This patch adds TLB preservation support to IOMMU module
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

Added the missing TLB valid entry setting for cam register
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

This patch includes changes to omap3-iommu.c file to make it generic
for all OMAPs. Renamed omap3-iommu.c to omap-iommu.c

[Hiroshi DOYU: Remove unnecessary "iommu-y" in Makefile]
Signed-off-by: NHari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>

The generic gpiolib provides a debugfs interface to GPIOs which
provides identical (but nicer looking) data as the OMAP specific one.

This patch completely drops the OMAP specific interface
(/debug/omap_gpio) in favor of using the generic one (/debug/gpio.)
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

setwkuena and setdataout are covered already by wake_en and dataout fields.
Signed-off-by: NTero Kristo <tero.kristo@nokia.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>