Move the defines to the associated board file and remove
the now unnecessary header files.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch removes old platform devices. Alsa should now
be using the ASoC driver. For boards not yet using ASoC,
please see sound/soc/omap/osk5912.c.

Add dummy aic23_power_up and aic23_power_down functions for 770
to keep things compiling.

Remove references to omap_gpio_switch, and unused h2_nand_dev_ready
function.

This patch is based on an earlier patch by Arun KS.

Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NArun KS <arunks@mistralsolutions.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Most of the omap1 MMC boards got broken by an earlier patch
138ab9f8. If you look closely,
the MMC init funtions are pretty much just stubs.

Remove broken init code to make room for cleaner MMC init code.

Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Switch to gpio_request/free calls
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.

(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

More conversion to the standard GPIO interfaces:  stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.

Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.

 - For the call sites which defined an initial value either
   before or after setting the direction, that value was used.

   When that value was previously assigned afterwards, this
   could eliminate a brief output glitch ... and possibly
   change behavior.  In a few cases (LCDs) several values
   were assigned together ... those were re-arranged to match
   the explicit sequence provided.

 - Some call sites didn't define such a value; so I chose an
   initial "off/reset" value that seemed to default to "off".

In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.

The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.

Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script.  Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:

s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Keymap fix for palmte and palmz71
Signed-off-by: NEduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch cleans up omap1 files to sync up with linux-omap tree:

- Remove omap-generic MMC config as it should be defined in board-*.c files
  instead of using board-generic.c
- New style I2C board_info from David Brownell <dbrownell@users.sourceforge.net>
- Init section fixes from Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch starts using introduced I2C bus registration helper by cleaning
up registration currently done in various places and by doing necessary
board file modifications.
Signed-off-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NLucas Woods <woodzy@gmail.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Palmz71 specific things - board file.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>