No functional changes - this only removes a variable which is set but
never read.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some devices running OpenWrt need this and it makes sense to add this
to ath9k_platform_data as the next patches will add a devicetree
(boolean) property for it as well.
Suggested-by: NVittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Merge the two allocation instead of separately allocating room for the
indication payload.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: NAnilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not sure this can happen, but seems like a reasonable sanity
check.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

just to comply to coding style.
Signed-off-by: NEduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: NJulian Calaby <julian.calaby@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).

But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)

For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.

While there, remove the unused ath10k pktlog headers.
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

<linux/semaphore.h> is not used anymore, so just remove the include.
Signed-off-by: NChaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.

Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Otherwise, the txrx-compl-task may access some bad memory?
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics'  mac80211 callback is implemented
to extend support for per station statistics from the driver.

Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211

This can also act as a placeholder for any new per STA stats support
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled

The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats

{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}

Fixes: f9575793 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.

Fixes: 3533bf6b ("ath9k: Fix regulatory compliance")
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Just setting the proper return for reading beyond the eeprom data.
Signed-off-by: NEduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.

Fix these by making the dereference happen later.

Addresses the following smatch warnings:

drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)

	[scan channel] --> [rx channel] --> [peer channel] -->
	[vdev channel] -->  [any vdev channel] --> [target oper channel]

'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.

During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.

'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")

    WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
    [<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
    (ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
    [<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
    [<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
    [<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
    [<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
    [<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])

Fixes:3b0499e9 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)

	ath10k_core_unregister -> ath10k_core_free_board_files

	...... device unplug spurious interrupt .........

	ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump  ...etc

Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.

Call trace:

 EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
 f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
  [<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since stations can now be added before association
(NL80211_FEATURE_FULL_AP_CLIENT_STATE support),
no supported rates are set when the station is added
to the fw, resulting in fw recovery.

Fix it by first configuring the AP basic rates as
the station configured rates (when the station is
first added to the driver), and after the station
was authorized re-configure it, now with the actual
supported rates.
Signed-off-by: NGuy Mishol <guym@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We obviously don't want to fall through in that switch. With this change
1) We wait for event (triggered by p2p_disc) as expected
2) We remove interface manually on timeout
3) We return 0 on success instead of -ENOTSUPP
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This header provides two inline functions using struct brcmf_if so we
need core.h to avoid:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_prof’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:368:13: error: dereferencing pointer to incomplete type
  return &ifp->vif->profile;
             ^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_vif’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:374:12: error: dereferencing pointer to incomplete type
  return ifp->vif;
            ^
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function can work just fine with const pointer, it only calls
alloc_netdev which take const as well. Moreover it makes this function
more flexible as some cfg80211 callback may provide const char * as
well, e.g. add_virtual_intf. This will be needed for more advanced
interface management.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Removing P2P interface is handled by sending a proper request to the
firmware. On success firmware triggers an event and driver's handler
removes a matching interface.

However on event timeout we remove interface directly from the cfg80211
callback. Current code doesn't handle this case correctly as it always
assumes rtnl to be unlocked.

Fix it by adding an extra rtnl_locked parameter to functions and calling
unregister_netdevice when needed.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Modern C standards expect the 'inline' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":

drivers/net/wireless/intel/ipw2x00/ipw2200.c:4096:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Modern C standards expect the 'static' keyword to come first in a
declaration, and we get a warning for this with "make W=1":

drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3353:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

'register' is a keyword in C and cannot be used in place of a
variable name, as shown by this -Wextra warning:

drivers/net/wireless/cisco/airo.c:1105:29: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]

This replaces the 'register' keyword with a 'reg' identifier in
the declaration, which matches the definition and has the intended
meaning.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's been observed that if interface type is changed from managed to
__ap, AP can be successfully started. But there is a problem if new
ap interface is added.

The problem got resolved after sending appropriate commands to firmware
in add_interface handler.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch populates secondary channel offset and downloads it to
firmware to fix the problem.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On some platforms, driver is unable to wakeup firmware after system resume
due to a problem at MMC subsystem. Triggering card reset in this case has
a race with card removal from MMC which causes system hang. This patch
resolves the problem by not triggering card reset.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It is obeserved that sometimes scan operation will block the disconnect
during system suspend. It's ok to cancel ongoing scan in this case. It
reduces unnecessary system suspend delay.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>