Many-many code in the kernel initialized the timer->function
and  timer->data together with calling init_timer(timer). There
is already a helper for this. Use it for networking code.

The patch is HUGE, but makes the code 130 lines shorter
(98 insertions(+), 228 deletions(-)).
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add raw drops counter for IPv6 in /proc/net/raw6 .
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add raw drops counter for IPv4 in /proc/net/raw .
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks to YOSHIFUJI Hideaki for the hint!
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support for network splice receive.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For release Linux removed this warning, but we want it
back for development.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs.  The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised.  This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.

The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: NRolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Replace all lock_cpu_hotplug/unlock_cpu_hotplug from the kernel and use
get_online_cpus and put_online_cpus instead as it highlights the
refcount semantics in these operations.

The new API guarantees protection against the cpu-hotplug operation, but
it doesn't guarantee serialized access to any of the local data
structures. Hence the changes needs to be reviewed.

In case of pseries_add_processor/pseries_remove_processor, use
cpu_maps_update_begin()/cpu_maps_update_done() as we're modifying the
cpu_present_map there.
Signed-off-by: NGautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

There is no need for kobject_unregister() anymore, thanks to Kay's
kobject cleanup changes, so replace all instances of it with
kobject_put().


Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This converts the code to use the new kobject functions, cleaning up the
logic in doing so.

Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The kobject in the bridge code is only used for registering with sysfs,
not for any lifespan rules.  This patch changes it to be only a pointer
and use the simpler api for this kind of thing.

Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit 81100eb8 for the
release, to avoid the unnecessary warning noise that is only really
relevant to wireless driver developers.

The warning will probably go right back in after I cut the release, but
at least we won't unnecessarily worry users.
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As it is ip_append_data only counts page fragments to the skb that
allocated it.  As such it means that the first skb gets hit with a
4K charge even though it might have only used a fraction of it while
all subsequent skb's that use the same page gets away with no charge
at all.

This bug was exposed by the UDP accounting patch.

[ The wmem_alloc bumping needs to be moved with the truesize,
  noticed by Takahiro Yasui.  -DaveM ]
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

init_net is used added as a parameter to a lot of old API calls, f.e.
ip_dev_find. These calls were exported as EXPORT_SYMBOL. So, export init_net
as EXPORT_SYMBOL to keep networking API consistent.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And as noted by Takahiro Yasui, we thus need to bump the
sk->sk_wmem_alloc at this spot as well.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rfcomm tty device will possibly retain even when conn is down, and
sysfs doesn't support zombie device moving, so this patch move the tty
device before conn device is destroyed.

For the bug refered please see :
http://lkml.org/lkml/2007/12/28/87Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "96793b48" (Add ICMPMsgStats
MIB (RFC 4293)) made a mistake.

In that patch, David L added a icmp_out_count() in
ip_push_pending_frames(), remove icmp_out_count() from
icmp_reply(). But he forgot to remove icmp_out_count() from
icmp_send() too.  Since icmp_send and icmp_reply will call
icmp_push_reply, which will call ip_push_pending_frames, a duplicated
increment happened in icmp_send.

This patch remove the icmp_out_count from icmp_send too.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The snmp6 entry name was changed, and it broke compatibility
to RFC 2011.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

icmpv6_send() calls ip6_push_pending_frames() indirectly.
Both ip6_push_pending_frames() and icmpv6_send() increment
counter ICMP6_MIB_OUTMSGS.

This patch remove the increment from icmpv6_send.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unregistering the rtnl_link_ops, all existing devices using
the ops are destroyed. With nested devices this may lead to a
use-after-free despite the use of for_each_netdev_safe() in case
the upper device is next in the device list and is destroyed
by the NETDEV_UNREGISTER notifier.

The easy fix is to restart scanning the device list after removing
a device. Alternatively we could add new devices to the front of
the list to avoid having dependant devices follow the device they
depend on. A third option would be to only restart scanning if
dev->iflink of the next device matches dev->ifindex of the current
one. For now this seems like the safest solution.

With this patch, the veth rtnl_link_ops unregistration can use
rtnl_link_unregister() directly since it now also handles destruction
of multiple devices at once.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here goes an IrDA patch against your latest net-2.6 tree.

This patch fixes some af_irda memory leaks.  It also checks for
irias_new_obect() return value.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NSamuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 9cd40029 (Fix race between
neigh_parms_release and neightbl_fill_parms) introduced device
reference counting regressions for several people, see:

	http://bugzilla.kernel.org/show_bug.cgi?id=9778

for example.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When packets are flood-forwarded to multiple output devices, the
bridge-netfilter code reuses skb->nf_bridge for each clone to store
the bridge port. When queueing packets using NFQUEUE netfilter takes
a reference to skb->nf_bridge->physoutdev, which is overwritten
when the packet is forwarded to the second port. This causes
refcount unterflows for the first device and refcount leaks for all
others. Additionally this provides incorrect data to the iptables
physdev match.

Unshare skb->nf_bridge by copying it if it is shared before assigning
the physoutdev device.

Reported, tested and based on initial patch by
Jan Christoph Nordholz <hesso@pool.math.tu-berlin.de>.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We omit (or delay) sending NSes for known-to-unreachable routers (in
NUD_FAILED state) according to RFC 4191 (Default Router Preferences
and More-Specific Routes).  But this is not fully compatible with RFC
4861 (Neighbor Discovery Protocol for IPv6), which does not remember
unreachability of neighbors.

So, let's avoid mixing sending algorithm of RFC 4191 and that of RFC
4861, and make the algorithm more friendly with RFC 4861 if RFC 4191
is disabled.

Issue was found by IPv6 Ready Logo Core Self_Test 1.5.0b2 (by TAHI
Project), and has been tracked down by Mitsuru Chinen
<mitch@linux.vnet.ibm.com>.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I noticed "ip route list" was slower than "cat /proc/net/route" on a
machine with a full Internet routing table (214392 entries : Special
thanks to Robert ;) )

This is similar to problem reported in commit
d8c92830 ("[IPV4] ROUTE: ip_rt_dump()
is unecessary slow")

Fix is to avoid scanning the begining of fz_hash table, but directly
seek to the right offset.

Before patch :

time ip route >/tmp/ROUTE

real    0m1.285s
user    0m0.712s
sys     0m0.436s

After patch

# time ip route >/tmp/ROUTE

real    0m0.835s
user    0m0.692s
sys     0m0.124s
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

http://bugzilla.kernel.org/show_bug.cgi?id=9493

The fib allows making identical routes with 'ip route replace'.
This patch makes the fib return -EEXIST if replacement would cause duplication.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

http://bugzilla.kernel.org/show_bug.cgi?id=9493

The fib allows making identical routes with 'ip route replace'.
This patch makes the fib return -EEXIST if replacement would cause duplication.
Signed-off-by: NJoonwoo Park <joonwpark81@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When looking for a conflicting connection the !sk->sk_bound_dev_if
check is performed only for live sockets, but not for timewait-ed.

This is not the case for ipv4, for __inet6_lookup_established in
both ipv4 and ipv6 and for other places that check for tw-s.

Was this missed accidentally? If so, then this patch fixes it and
besides makes use if the dif variable declared in the function.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code inspection turned up that error cases in rfkill_register() do not
call rfkill_led_trigger_unregister() even though we have already
registered.
Signed-off-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge code incorrectly causes two POST_ROUTING hook invocations
for DNATed packets that end up on the same bridge device. This
happens because packets with a changed destination address are passed
to dst_output() to make them go through the neighbour output function
again to build a new destination MAC address, before they will continue
through the IP hooks simulated by bridge netfilter.

The resulting hook order is:
 PREROUTING	(bridge netfilter)
 POSTROUTING	(dst_output -> ip_output)
 FORWARD	(bridge netfilter)
 POSTROUTING	(bridge netfilter)

The deferred hooks used to abort the first POST_ROUTING invocation,
but since the only thing bridge netfilter actually really wants is
a new MAC address, we can avoid going through the IP stack completely
by simply calling the neighbour output function directly.

Tested, reported and lots of data provided by: Damien Thebault <damien.thebault@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the @helper variable that was just obtained.
Signed-off-by: NJan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC2464 says that the next to lowerst order bit of the first octet
of the Interface Identifier is formed by complementing
the Universal/Local bit of the EUI-64. But ip6t_eui64 uses OR not XOR.

Thanks Peter Ivancik for reporing this bug and posting a patch
for it.
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow vlans nesting other vlans without lockdep's warnings (max. 2 levels
i.e. parent + child). Thanks to Patrick McHardy for pointing a bug in the
first version of this patch.

Reported-by: Benny Amorsen
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In dn_rt_cache_get_next(), no need to guard seq->private by a
rcu_dereference() since seq is private to the thread running this
function. Reading seq.private once (as guaranted bu rcu_dereference())
or several time if compiler really is dumb enough wont change the
result.
 
But we miss real spots where rcu_dereference() are needed, both in
dn_rt_cache_get_first() and dn_rt_cache_get_next()
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) In tty.c the BUG_ON at line 115 will never be called, because the the
   before list_del_init in this same function.
	115          BUG_ON(!list_empty(&dev->list));
   So move the list_del_init to rfcomm_dev_del 

2) The rfcomm_dev_del could be called from diffrent path
   (rfcomm_tty_hangup/rfcomm_dev_state_change/rfcomm_release_dev),

   So add another BUG_ON when the rfcomm_dev_del is called more than
   one time.
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bernard Pidoux F6BVP reported:
> When I killall kissattach I can see the following message.
>
> This happens on kernel 2.6.24-rc5 already patched with the 6 previously
> patches I sent recently.
>
>
> =======================================================
> [ INFO: possible circular locking dependency detected ]
> 2.6.23.9 #1
> -------------------------------------------------------
> kissattach/2906 is trying to acquire lock:
>  (linkfail_lock){-+..}, at: [<d8bd4603>] ax25_link_failed+0x11/0x39 [ax25]
>
> but task is already holding lock:
>  (ax25_list_lock){-+..}, at: [<d8bd7c7c>] ax25_device_event+0x38/0x84
> [ax25]
>
> which lock already depends on the new lock.
>
>
> the existing dependency chain (in reverse order) is:
...

lockdep is worried about the different order here:

#1 (rose_neigh_list_lock){-+..}:
#3 (ax25_list_lock){-+..}:

#0 (linkfail_lock){-+..}:
#1 (rose_neigh_list_lock){-+..}:

#3 (ax25_list_lock){-+..}:
#0 (linkfail_lock){-+..}:

So, ax25_list_lock could be taken before and after linkfail_lock. 
I don't know if this three-thread clutch is very probable (or
possible at all), but it seems another bug reported by Bernard
("[...] system impossible to reboot with linux-2.6.24-rc5")
could have similar source - namely ax25_list_lock held by
ax25_kill_by_device() during ax25_disconnect(). It looks like the
only place which calls ax25_disconnect() this way, so I guess, it
isn't necessary.

This patch is breaking the lock for ax25_disconnect().
Reported-and-tested-by: NBernard Pidoux <f6bvp@free.fr>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sfuzz can easily trigger any of those.

move the printk message to the corresponding comment: makes the
intention of the code clear and easy to pick up on an scheduled
removal.  as bonus simplify the braces placement.
Signed-off-by: Nmaximilian attems <max@stro.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>