The Blackfin port doesn't support HAVE_CLK and the musb driver works fine
with support stubbed out, so take the existing Blackfin clk stubs and move
them to common musb code so we can drop the Kconfig dependency.
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When an endpoint is to be dropped from the hardware bandwidth schedule, we
want to clear its add flag.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the host controller dies or is removed while a device is plugged in,
the USB core will attempt to deallocate the struct usb_device.  That will
call into xhci_free_dev().  This function used to attempt to submit a
disable slot command to the host controller and clean up the device
structures when that command returned.  Change xhci_free_dev() to skip the
command submission and just free the memory if the host controller died.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the host controller dies (e.g. it is removed from a PCI card slot),
the xHCI driver cannot expect commands to complete.  The buggy code this
patch fixes would mark an URB as canceled and then expect the URB to be
completed when the stop endpoint command completed.  That would never
happen if the host controller was dead, so the USB core would just hang in
the disconnect code.

If the host controller died, and the driver asks to cancel an URB, free
any structures associated with that URB and immediately give it back.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the host controller card is removed from the system, stop the timer
function to debug the xHCI rings.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current 10ms timeout is too short for some normal USBTMC device
operation, increase it to a value which was tested with previously
affected Tektronix oscilloscopes.
Signed-off-by: NGergely Imreh <imrehg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPeter Magdina <peter@magdina.sk>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Stanse found a memory leak in lcd_probe. Instead of returning without
releasing the memory, jump to the error label which frees it.

http://stanse.fi.muni.cz/Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: NElina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method.  This causes some drivers (io_ti in particular) to perform an
invalid memory access.

The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NJean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a regression introduced in
39892da4.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix regression introduced by commit
d4fc4a7b (tty: Fix the PL2303 private
methods for sysrq).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Re-structure read processing.
 - Kill obsolete work queue and always push to tty in completion handler.
 - Use tty_insert_flip_string instead of per character push when
   possible.
 - Fix stalled-read regression in 2.6.31 by using urb status to
   determine when port is closed rather than port count.
 - Fix race with open/close by checking ASYNCB_INITIALIZED in
   unthrottle.
 - Kill private rx_flag and lock and use throttle flags in
   usb_serial_port instead.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove superfluous error checks in completion handler:

 - No need to check private data and urb pointers as we check urb-status
   before dereferencing priv (which is not freed until urb has been killed
   on close).
 - No need to check tty as it is checked again when processing.
 - No need to check urb->number_of_packets on bulk urb.

Note that both private data and tty are checked again before processing
(possibly from work queue which also is cancelled on close).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove unused rx_byte counter which is never exposed as noted by Alan
Cox.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes tty_flip_buffer_push being called from hard interrupt context with
low_latency set.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[akpm@linux-foundation.org: fix KVM]
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following commit made console open fails while booting:

	commit b50989dc
	Author: Alan Cox <alan@linux.intel.com>
	Date:   Sat Sep 19 13:13:22 2009 -0700

	tty: make the kref destructor occur asynchronously

Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:

INIT open /dev/console Input/output error

It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229

The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.

Fix it as per the following Alan's suggestion:

  Fun but it's actually not a bug and the fix is wrong in itself as
  the port may be closing but not yet being destructed, in which case
  it seems to do the wrong thing.  Opening a tty that is closing (and
  could be closing for long periods) is supposed to return -EIO.

  I suspect a better way to deal with this and keep the old console
  timing is to split tty->shutdown into two functions.

  tty->shutdown() - called synchronously just before we dump the tty
  onto the waitqueue for destruction

  tty->cleanup() - called when the destructor runs.

  We would then do the shutdown part which can occur in IRQ context
  fine, before queueing the rest of the release (from tty->magic = 0
  ...  the end) to occur asynchronously

  The USB update in -next would then need a call like

       if (tty->cleanup)
               tty->cleanup(tty);

  at the top of the async function and the USB shutdown to be split
  between shutdown and cleanup as the USB resource cleanup and final
  tidy cannot occur synchronously as it needs to sleep.

  In other words the logic becomes

       final kref put
               make object unfindable

       async
               clean it up
Signed-off-by: NDave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ]
Signed-off-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
  comments from Alan Stern  - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code

But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
  is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/usb/serial/sierra.c: In function 'sierra_suspend':
drivers/usb/serial/sierra.c:936: error: 'struct usb_device' has no member named 'auto_pm'

Repairs

commit e6929a90
Author: Oliver Neukum <oliver@neukum.org>
Date:   Fri Sep 4 23:19:53 2009 +0200

    USB: support for autosuspend in sierra while online

Cc: Greg KH <greg@kroah.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* remove asm/atomic.h inclusion from linux/utsname.h --
   not needed after kref conversion
 * remove linux/utsname.h inclusion from files which do not need it

NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes up the majority of the coding style issues in the
usb-skeleton driver.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Non blocking IO is supported in the read path of usb-skeleton.
This is done by just not blocking. As support for handling signals
without stopping IO is already there, it can be used for O_NONBLOCK, too.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb:usb-skeleton: honor O_NONBLOCK in write path

nonblocking writes are allowed by using down_trylock if necessary
to reserve an URB
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The read code path of the skeleton driver really sucks

 - skel_read works only for devices which always send data
 - the timeout comes out of thin air
 - it blocks signals for the duration of the timeout
 - it disallows nonblocking IO by design

This patch fixes it by using a real urb, a completion and interruptible waits.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a hook for updating xHCI internal structures after khubd fetches the
hub descriptor and sets up the hub's TT information.  The xHCI driver must
update the internal structures before devices under the hub can be
enumerated.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For a USB hub to work under an xHCI host controller, the xHC's internal
scheduler must be made aware of the hub's characteristics.  Add an xHCI
hook that the USB core will call after it fetches the hub descriptor.
This hook will add hub information to the slot context for that device,
including whether it has multiple TTs or a single TT, the number of ports
on the hub, and TT think time.

Setting up the slot context for the device is different for 0.95 and 0.96
xHCI host controllers.

Some of the slot context reserved fields in the 0.95 specification were
changed into hub fields in the 0.96 specification.  Don't set the TT think
time or number of ports for a hub if we're dealing with a 0.95-compliant
xHCI host controller.

The 0.95 xHCI specification says that to modify the hub flag, we need to
issue an evaluate context command.  The 0.96 specification says that flag
can be set with a configure endpoint command.  Issue the correct command
based on the version reported by the hardware.

This patch does not add support for multi-TT hubs.  Multi-TT hubs expose
a single TT on alt setting 0, and multi-TT on alt setting 1.  The xHCI
driver can't handle setting alternate interfaces yet.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When setting up a slot context for an address device command, set the
multi-TT field if this is a low or full speed device under a HS hub with
multiple transaction translators.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xHCI driver needs to set the route string in the slot context of all
devices, not just SuperSpeed devices.  The route string concept was added
in the USB 3.0 specification, section 10.1.3.2.  Each hub in the topology
is expected to have no more than 15 ports in order for the route string of
a device to be unique.  SuperSpeed hubs are restricted to only having 15
ports, but FS/LS/HS hubs are not.  The xHCI specification says that if the
port number the device is under is greater than 15, that portion of the
route string shall be set to 15.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the xHCI driver, configure endpoint commands that are submitted to the
hardware may involve one of two data structures.  If the configure
endpoint command is setting up a new configuration or modifying max packet
sizes, the data structures and completions are statically allocated in the
xhci_virt_device structure.  If the command is being used to set up
streams or add hub information, then the data structures are dynamically
allocated, and placed on a device command waiting list.

Break out the code to check whether a completed command is in the device
command waiting list.  Fix a subtle bug in the old code: continue
processing the command if the command isn't in the wait list.  In the old
code, if there was a command in the wait list, but it didn't match the
completed command, the completed command event would be dropped.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some commands to the xHCI hardware cannot be allowed to fail due to out of
memory issues or the command ring being full.

Add a way to reserve a TRB on the command ring, and make all command
queueing functions indicate whether they are using a reserved TRB.

Add a way to pre-allocate all the memory a command might need.  A command
needs an input context, a variable to store the status, and (optionally) a
completion for the caller to wait on.  Change all code that assumes the
input device context, status, and completion for a command is stored in
the xhci virtual USB device structure (xhci_virt_device).

Store pending completions in a FIFO in xhci_virt_device.  Make the event
handler for a configure endpoint command check to see whether a pending
command in the list has completed.  We need to use separate input device
contexts for some configure endpoint commands, since multiple drivers can
submit requests at the same time that require a configure endpoint
command.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Refactor common code to set up the add and drop flags for the input device
context setup.  This setup is used before a configure endpoint command for
the reset endpoint quirk, and will be used for the command to alloc or
free streams rings.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The xhci_ring structure contained information that is really related to an
endpoint, not a ring.  This will cause problems later when endpoint
streams are supported and there are multiple rings per endpoint.

Move the endpoint state and cancellation information into a new virtual
endpoint structure, xhci_virt_ep.  The list of TRBs to be cancelled should
be per endpoint, not per ring, for easy access.  There can be only one TRB
that the endpoint stopped on after a stop endpoint command (even with
streams enabled); move the stopped TRB information into the new virtual
endpoint structure.  Also move the 31 endpoint rings and temporary ring
storage from the virtual device structure (xhci_virt_device) into the
virtual endpoint structure (xhci_virt_ep).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix build error, ether uses/needs to select CRC32 config symbol:

ether.c:(.text+0x271480): undefined reference to `crc32_le'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In order:
Add reference to relevant section of USBTMC usb488 subclass specs.
Print debug output of capabilities only when it was retrieved successfully.
Clear return value on success, otherwise driver always reports failure.
Signed-off-by: NGergely Imreh <imrehg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb: check for IO errors usb_set_interface can return

if they happen while unbinding a flag is set to retry upon probe
if they happen during probe they are handled as probe errors
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1283) adds a new flag, USBDEVFS_URB_BULK_CONTINUATION,
to usbfs.  It is intended for userspace libraries such as libusb and
openusb.  When they have to break up a single usbfs bulk transfer into
multiple URBs, they will set the flag on all but the first URB of the
series.

If an error other than an unlink occurs, the kernel will automatically
cancel all the following URBs for the same endpoint and refuse to
accept new submissions, until an URB is encountered that is not marked
as a BULK_CONTINUATION.  Such an URB would indicate the start of a new
transfer or the presence of an older library, so the kernel returns to
normal operation.

This enables libraries to delimit bulk transfers correctly, even in
the presence of early termination as indicated by short packets.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>