The ADAU1701 has 12 pins that can be configured depending on the system
configuration. Allow settting the corresponding registers from DT.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ADAU1701 has 2 hardware pins to configure the PLL mode in accordance
to the MCLK-to-LRCLK ratio. These pins have to be stable before the chip
is released from reset, and a full reset cycle, including a new firmware
download is needed whenever they change.

This patch adds GPIO properties to the DT bindings of the Codec, and
implements makes the set_sysclk memorize the configured sysclk.

Because the run-time parameters are unknown at probe time, the first
firmware download is postponed to the first hw_params call, when the
driver can determine the mclk/lrclk divider. Subsequent downloads
are only issued when the divider configuration changes.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for the at91sam9x5-family which must use the shadow
interrupt mask due to a hardware issue (causing RTC_IMR to always be
zero).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

A simple frame-buffer describes a raw memory region that may be rendered
to, with the assumption that the display hardware has already been set
up to scan out from that buffer.

This is useful in cases where a bootloader exists and has set up the
display hardware, but a Linux driver doesn't yet exist for the display
hardware.

Examples use-cases include:

* The built-in LCD panels on the Samsung ARM chromebook, and Tegra
  devices, and likely many other ARM or embedded systems.  These cannot
  yet be supported using a full graphics driver, since the panel control
  should be provided by the CDF (Common Display Framework), which has been
  stuck in design/review for quite some time.  One could support these
  panels using custom SoC-specific code, but there is a desire to use
  common infra-structure rather than having each SoC vendor invent their
  own code, hence the desire to wait for CDF.

* Hardware for which a full graphics driver is not yet available, and
  the path to obtain one upstream isn't yet clear.  For example, the
  Raspberry Pi.

* Any hardware in early stages of upstreaming, before a full graphics
  driver has been tackled.  This driver can provide a graphical boot
  console (even full X support) much earlier in the upstreaming process,
  thus making new SoC or board support more generally useful earlier.

[akpm@linux-foundation.org: make simplefb_formats[] static]
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NOlof Johansson <olof@lixom.net>
Cc: Rob Clark <robclark@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ensure the compatible property for FIMC-LITE IP blocks is properly
documented, a cut&paste error fix.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This patch adds binding documentation for the
compatible values of the Ralink MIPS SoCs.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5187/

Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC NAND example.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC ethernet binding.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>

Update at_hdmac driver to support generic DMA device tree binding. Devices
can still request channel with dma_request_channel() then it doesn't break
DMA for non DT boards.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMatus Ujhelyi <matus.ujhelyi@streamunlimited.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMatus Ujhelyi <matus.ujhelyi@streamunlimited.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable supporting the DT structure of LP855x family devices.  If the
platform data is NULL, the driver tries to parse a DT structure.  Then,
the platform data is copied from the DT.  Documentation is added as well.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch depends on "genalloc: add devres support, allow to find a
managed pool by device", which provides the of_get_named_gen_pool and
dev_get_gen_pool functions.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NJavier Martin <javier.martin@vista-silicon.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Huang Shijie <shijie8@gmail.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver requests and remaps a memory region as configured in the
device tree.  It serves memory from this region via the genalloc API.  It
optionally enables the SRAM clock.

Other drivers can retrieve the genalloc pool from a phandle pointing to
this drivers' device node in the device tree.

The allocation granularity is hard-coded to 32 bytes for now, to make the
SRAM driver useful for the 6502 remoteproc driver.  There is overhead for
bigger SRAMs, where only a much coarser allocation granularity is needed:
At 32 bytes minimum allocation size, a 256 KiB SRAM needs a 1 KiB bitmap
to track allocations.

[akpm@linux-foundation.org: fix Kconfig text, make sram_init static]
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NMichal Simek <monstr@monstr.eu>
Cc: Dong Aisheng <dong.aisheng@linaro.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Huang Shijie <shijie8@gmail.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Matt Porter <mporter@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds missing documentation describing Device Tree bindings
for Samsung PWM timers.
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Patch adds device tree probe support for mc13783-regulator driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMark Brown <broonie@sirena.org.uk>

The drivers sets up an irq domain and hands out unique irqs to irq
capable gpio lines regardless of how underlying irq maps to gpio
lines. Any gpio line can map to any one or none of the irqs of the
core, independently of each other.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This driver supports GRGPIO gpio cores available in the GRLIB VHDL IP
core library from Aeroflex Gaisler.
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

This patch allows timeriomem_rng to be used via devicetree.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This adds a driver for random number generator present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: NDom Cobley <popcornmix@gmail.com>
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Fix spelling typos in Documentation/devicetree/bindings.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Support the BGR666 format on the IPUv3 parallel display.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a dwc_platform.ko module that can be loaded by using
compatible = "snps,dwc2" in a device tree.
Signed-off-by: NMatthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a complete DT binding for the arasan device driver. There is
currently only one user, which is the spear13xx platform, so we don't
actually have to parse all the properties until another user comes in,
but this does use the generic DMA binding to find the DMA channel.

The patch is untested so far and is part of a series to convert
the spear platform over to use the generic DMA binding, so it
should stay with the rest of the series.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NViresh Kumar <viresh.linux@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: devicetree-discuss@lists.ozlabs.org

Add properties for some of the more important bits of platform data and
fill out the binding document.

Not all of the current platform data is suitable for the sort of fixed
configuration that is done using DT, some of it should have runtime
mechanisms added instead and some is unlikely to ever be used in practical
systems.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add binding documentation for spi-davinci module.

[prakash.pm@ti.com: Follow DT naming convention for compatible property]
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The i2c-arb-gpio-challenge driver implements an I2C arbitration scheme
where masters need to claim the bus with a GPIO before they can start
a transaction.  This should generally only be used when standard I2C
multimaster isn't appropriate for some reason (errata/bugs).

This driver is based on code that Simon Glass added to the i2c-s3c2410
driver in the Chrome OS kernel 3.4 tree.  The current incarnation as a
mux driver is as suggested by Grant Likely.  See
<https://patchwork.kernel.org/patch/1877311/> for some history.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This property is meant to be used in device nodes which represent
power_supply devices that wish to provide a list of supplies which
provide them power, such as a battery listing its chargers.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NAnton Vorontsov <anton@enomsg.org>

This reverts commit 09495dda.
The description is incomplete and the location of this file
is incorrect. Based on discussion with the Samsung media and DRM subsystem
maintainers, the documentaion of Samsung G2D bindings has been placed at:
Documentation/devicetree/bindings/gpu/samsung-g2d.txt
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Binding Documents for drm-devices are placed in
Documentation/devicetree/bindings/drm/*. But these devices are common
for v4l framework, hence moved to a common place at
Documentation/devicetree/bindings/video/. 'exynos_' prefix is added to
associate them with exynos soc series.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

add a missing double quote for compatible property for pmx_wkup.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We add the possibility to hand over a GPIO number for the reset pin.
This way we can remove existing board code that takes care of it and
group this information properly in the platform data or in the device
tree configuration.
Signed-off-by: NBastian Hecht <hechtb+renesas@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Adds the main PLL clock groups for SOCFPGA into device tree file
so that the clock framework to query the clock and clock rates
appropriately.

$cat /sys/kernel/debug/clk/clk_summary
   clock                        enable_cnt  prepare_cnt  rate
---------------------------------------------------------------------
 osc1                           2           2            25000000
    sdram_pll                   0           0            400000000
       s2f_usr2_clk             0           0            66666666
       ddr_dq_clk               0           0            200000000
       ddr_2x_dqs_clk           0           0            400000000
       ddr_dqs_clk              0           0            200000000
    periph_pll                  2           2            500000000
       s2f_usr1_clk             0           0            50000000
       per_base_clk             4           4            100000000
       per_nand_mmc_clk         0           0            25000000
       per_qsi_clk              0           0            250000000
       emac1_clk                1           1            125000000
       emac0_clk                0           0            125000000
    main_pll                    1           1            1600000000
       cfg_s2f_usr0_clk         0           0            100000000
       main_nand_sdmmc_clk      0           0            100000000
       main_qspi_clk            0           0            400000000
       dbg_base_clk             0           0            400000000
       mainclk                  0           0            400000000
       mpuclk                   1           1            800000000
          smp_twd               1           1            200000000
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Reviewed-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Adding devicetree support for imx21-mmc and imx31-mmc. Based on generic
gpio helper functions by Guennadi and generic DMA devicetree bindings.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>