- 23 4月, 2011 1 次提交
-
-
由 Felipe Balbi 提交于
it makes it simpler to keep track of the amount of bytes received and simplifies how flush_to_ldisc counts the remaining bytes. It also fixes a bug of lost bytes on n_tty when flushing too many bytes via the USB serial gadget driver. Tested-by: NStefan Bigler <stefan.bigler@keymile.com> Tested-by: NToby Gray <toby.gray@realvnc.com> Signed-off-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 11 4月, 2011 1 次提交
-
-
由 Steve Glendinning 提交于
This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB ethernet controllers to the existing smsc95xx driver by adding their new USB VID/PID pairs. Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 4月, 2011 2 次提交
-
-
由 Yevgeny Petrilin 提交于
If not done, second attempt to open the RX ring would cause memory corruption. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
When bringing the port up, performing a SENSE_PORT command To try and check to which physical link type (IB or Ethernet) the physical port is connected. In case there is no valid link partner, the port will come up as its supported default. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 4月, 2011 7 次提交
-
-
由 Padmanabh Ratnakar 提交于
eq_next_idx is not getting reset to zero during suspend. This causes resume to fail. Added the fix. Signed-off-by: NSarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com> Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Padmanabh Ratnakar 提交于
Renamed msix_vec_idx to eq_idx in be_eq_obj struct. Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure. These members are used in INTX mode also. Signed-off-by: NSarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com> Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ulrich Weber 提交于
otherwise we loop forever if a PPPoE socket was set to PPPOX_ZOMBIE state by a PADT message when the ethernet device is going down afterwards. Signed-off-by: NUlrich Weber <uweber@astaro.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ajit Khaparde 提交于
adapter could remain uninitialized if probe fails for some reason. A null pointer access could cause a crash if be_shutdown is called after that. Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rasesh Mody 提交于
This patch contains a fix for gracefully handling firmware heartbeat failure instead of forcing panic. Signed-off-by: NDebashis Dutt <ddutt@brocade.com> Signed-off-by: NRasesh Mody <rmody@brocade.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Enric Balletbo i Serra 提交于
When an interrupt occurs, the INT pin is driven low by the MCP251x controller (falling edge) but in some cases the INT pin can be connected to the MPU through a transistor or level translator which inverts this signal. In this case interrupt should be configured in rising edge. This patch adds support to pass the IRQ flags via mcp251x_platform_data. Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: NWolfgang Grandegger <wg@grandegger.com> Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Enric Balletbo i Serra 提交于
When SMSC911X_SAVE_MAC_ADDRESS flag is enabled the driver calls smsc911x_mac_read and smsc911x_mac_read function without acquiring mac_lock spinlock This patch fixes following warning smsc911x: Driver version 2008-10-21. ------------[ cut here ]------------ WARNING: at drivers/net/smsc911x.c:261 smsc911x_mac_read+0x24/0x220() Modules linked in: [<c0060858>] (unwind_backtrace+0x0/0xe0) from [<c009322c>] (warn_slowpath_common+0x4c/0x64) [<c009322c>] (warn_slowpath_common+0x4c/0x64) from [<c009325c>] (warn_slowpath_null+0x18/0x1c) [<c009325c>] (warn_slowpath_null+0x18/0x1c) from [<c0324bec>] (smsc911x_mac_read+0x24/0x220) [<c0324bec>] (smsc911x_mac_read+0x24/0x220) from [<c0434788>] (smsc911x_read_mac_address+0x18/0x6c) [<c0434788>] (smsc911x_read_mac_address+0x18/0x6c) from [<c0434c74>] (smsc911x_drv_probe+0x498/0x1788) [<c0434c74>] (smsc911x_drv_probe+0x498/0x1788) from [<c02d3e54>] (platform_drv_probe+0x14/0x18) [<c02d3e54>] (platform_drv_probe+0x14/0x18) from [<c02d2d60>] (driver_probe_device+0xc8/0x184) [<c02d2d60>] (driver_probe_device+0xc8/0x184) from [<c02d2e84>] (__driver_attach+0x68/0x8c) [<c02d2e84>] (__driver_attach+0x68/0x8c) from [<c02d1fc8>] (bus_for_each_dev+0x48/0x74) [<c02d1fc8>] (bus_for_each_dev+0x48/0x74) from [<c02d2660>] (bus_add_driver+0x9c/0x228) [<c02d2660>] (bus_add_driver+0x9c/0x228) from [<c02d3598>] (driver_register+0xa0/0x124) [<c02d3598>] (driver_register+0xa0/0x124) from [<c0050668>] (do_one_initcall+0x94/0x168) [<c0050668>] (do_one_initcall+0x94/0x168) from [<c0008984>] (kernel_init+0xa0/0x154) [<c0008984>] (kernel_init+0xa0/0x154) from [<c005afac>] (kernel_thread_exit+0x0/0x8) ---[ end trace 2c931a35b7885770 ]--- Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 4月, 2011 10 次提交
-
-
由 John W. Linville 提交于
A number of these devices have appeared "in the wild", and apparently the Windows driver is perfectly happy to support this EEPROM version. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Cc: stable@kernel.org Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
-
由 Stanislaw Gruszka 提交于
{rx,tx}done_work's are only initialized for usb devices. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Cc: stable@kernel.org Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Larry Finger 提交于
Some compiler/architecture combinations generate some warnings that are not seen on my main system. Two of the "warnings" about unitialized variables are really bugs. Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
Cc: <stable@kernel.org> Reported-by: Mark Davis [via p54/devices wiki] Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luciano Coelho 提交于
We were allocating the size of the NVS file struct and not checking whether the length of the buffer passed was correct before copying it into the allocated memory. This is a security hole because buffer overflows can occur if the userspace passes a bigger file than what is expected. With this patch, we check if the size of the data passed from userspace matches the size required. This bug was introduced in 2.6.36. Cc: stable@kernel.org Reported-by: NIdo Yariv <ido@wizery.com> Signed-off-by: NLuciano Coelho <coelho@ti.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when reseting rx idle timer in urb completion handler. Move timer reseting to tasklet. Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jussi Kivilinna 提交于
Patch removes the bogus flag introduced by upstream commit eefdbec1. Old code had buffer length check that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging enabled bogus flag caused usb_submit_urb fail. Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion handler. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092Reported-by: NJonathan Callen <abcd@gentoo.org> Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Senthil Balasubramanian 提交于
The phy information print during driver init time doesn't show the numeric part of the chip name properly for AR9485. This patch addresses this issue by adding the string to the respective array. Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luciano Coelho 提交于
The MODULE_AUTHOR() macro in the main module (wl12xx) has been updated to reflect one of the author's new email address, but the wl12xx_spi and wl12xx_sdio modules haven't been updated. This patches updates them. Signed-off-by: NLuciano Coelho <coelho@ti.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Otherwise, skb_put inside of dma_rx can fail... https://bugzilla.kernel.org/show_bug.cgi?id=32042Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Acked-by: NLarry Finger <Larry.Finger@lwfinger.net> Cc: stable@kernel.org
-
- 04 4月, 2011 1 次提交
-
-
由 Mariusz Kozlowski 提交于
On error path kfree() should get pointer to memory allocated by kmalloc() not the address of variable holding it (which is on stack). Signed-off-by: NMariusz Kozlowski <mk@lab.zgora.pl> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 4月, 2011 2 次提交
-
-
由 Arnd Bergmann 提交于
The documentation for the USB ethernet devices suggests that only some devices are supposed to use usb0 as the network interface name instead of eth0. The logic used there, and documented in Kconfig for CDC is that eth0 will be used when the mac address is a globally assigned one, but usb0 is used for the locally managed range that is typically used on point-to-point links. Unfortunately, this has caused a lot of pain on the smsc95xx device that is used on the popular pandaboard without an EEPROM to store the MAC address, which causes the driver to call random_ether_address(). Obviously, there should be a proper MAC addressed assigned to the device, and discussions are ongoing about how to solve this, but this patch at least makes sure that the default interface naming gets a little saner and matches what the user can expect based on the documentation, including for new devices. The approach taken here is to flag whether a device might be a point-to-point link with the new FLAG_POINTTOPOINT setting in the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one of the two. The usbnet framework only looks at the MAC address for device naming if both flags are set, otherwise it trusts the flag. Signed-off-by: NArnd Bergmann <arnd.bergmann@linaro.org> Tested-by: NAndy Green <andy.green@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 FUJITA Tomonori 提交于
Now we have CONFIG_ARCH_DMA_ADDR_T_64BIT. We can fix the hacky dma_addr_t size test cleanly. Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 31 3月, 2011 4 次提交
-
-
由 Lucas De Marchi 提交于
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>
-
由 Yevgeny Petrilin 提交于
We should reduce the number of reserved completion queues from the total number of entries. Since the queue size is power of two, not reducing the reserved entries, caused a double queue size, which may lead to allocation failures in some cases. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
In case of allocation failure, tried to use the promiscuous QP entry that was previously freed. Now freeing this entry only in case we will not put it back to the list of promiscuous entries. Reported-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Pan(潘卫平) 提交于
use accumulates instead of acumulates. Signed-off-by: NPan Weiping <panweiping3@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2011 10 次提交
-
-
由 Jesper Juhl 提交于
We leak in some error paths of drivers/net/atlx/atl2.c:atl2_set_eeprom(). The memory allocated to 'eeprom_buff' is not freed when we return -EIO. This patch fixes that up and also removes a pointless explicit cast. Signed-off-by: NJesper Juhl <jj@chaosbits.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrzej Zaborowski 提交于
This adds a driver for the CDC Ethernet part of this modem. The device's ID is blacklisted in cdc_ether.c and is white-listed in this new driver because of the quirks needed to make it useful. The modem's firmware exposes a CDC ACM port for modem control and a CDC Ethernet port for network data. The descriptors look fine but both ports actually are some sort of multiplexers requiring non- standard headers added/removed from every packet or they get ignored. All information is based on a usb traffic log from a Windows machine. On the Verizon 4G network I've seen speeds up to 1.1MB/s so far with this driver, a speed-o-meter site reports 16.2Mbps/10.5Mbps. Userspace scripts are required to talk to the CDC ACM port. Signed-off-by: NAndrzej Zaborowski <balrogg@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marc Kleine-Budde 提交于
The function phy_attach_direct attaches the phy and calls phy_init_hw. phy_init_hw can fail, but the phy is still marked as attached. Successive calls to phy_attach_direct will fail because the phy is busy. [ 1.020000] eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:00, irq=-1) [ 1.030000] eth1: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1) [ 2.050000] Sending DHCP requests . [ 3.020000] PHY: 1:00 - Link is Up - 100/Full [ 5.110000] ..... timed out! [ 87.660000] IP-Config: Reopening network devices... [ 88.190000] FEC: MDIO read timeout [ 88.190000] eth0: could not attach to PHY [ 88.190000] IP-Config: Failed to open eth0 [ 88.210000] FEC: MDIO read timeout [ 88.210000] eth1: could not attach to PHY [ 88.210000] IP-Config: Failed to open eth1 [ 88.220000] IP-Config: No network devices available. [ 88.220000] Freeing init memory: 6968K [...] starting network interfaces... ip: RTNETLINK answers: File exists [ 94.000000] net eth0: PHY already attached [ 94.010000] eth0: could not attach to PHY ip: SIOCSIFFLAGS: Device or resource busy This patch adds phy_detach to clean up if phy_init_hw fails. Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ben Hutchings 提交于
via-ircc has been passing a NULL pointer to DMA allocation functions, which is completely invalid and results in a BUG on PowerPC. Now that we always have the device pointer available, pass it in. Reference: http://bugs.debian.org/619450Reported-by: NAndrew Buckeridge <andrewb@bgc.com.au> Signed-off-by: NBen Hutchings <ben@decadent.org.uk> Tested-by: Andrew Buckeridge <andrewb@bgc.com.au> [against 2.6.32] Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ben Hutchings 提交于
via-ircc still maintains its own array of device pointers in Linux 2.4 style. Worse, it always uses index 0, so it will crash if there are multiple suitable devices in the system. Signed-off-by: NBen Hutchings <ben@decadent.org.uk> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Johannes Berg 提交于
If change_interface gets invoked during a firmware restart, it may crash; prevent that from happening by checking if ctx->vif is assigned. Additionally, in my initial commit I forgot to set the vif->p2p variable correctly, so fix that too. Cc: stable@kernel.org [2.6.38+] Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
Some clients seem to rely upon the reception of BlockAckReqs to flush their rx reorder buffer. In order to fix aggregation for these clients carl9170 should set IEEE80211_TX_STAT_AMPDU_NO_BACK to generate a BlockAckReq if the transmission of an AMPDU subframe fails. This fixes aggregation problems with Intel 5100 Windows STAs (and maybe others as well). Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
After new NetworkManager 0.8.996 changes, hardware scanning is causing microcode errors as reported here: https://bugzilla.redhat.com/show_bug.cgi?id=683571 and sometimes kernel crashes: https://bugzilla.redhat.com/show_bug.cgi?id=688252 Also with hw scan there are very bad performance on some systems as reported here: https://bugzilla.redhat.com/show_bug.cgi?id=671366 Since Intel no longer supports 3945, there is no chance to get proper firmware fixes, we need workaround problems by disable hardware scanning by default. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Xose Vazquez Perez 提交于
taken from staging/rt2860 0x0411,0x016f de37cd49 MelCo(Buffalo) WLI-UC-G301N 0x050d,0x825b 12840c63 Belkin F5D8055 0x050d,0x935a 705059a6 Belkin F6D4050 v1 0x050d,0x935b 5d92fe33 Belkin F6D4050 v2 identifed from ralink driverss 0x0930,0x0a07 RT35xx TOSHIBA 2010_1215_RT3572_Linux_STA_v2.5.0.0.DPO 0x1d4d,0x0011 3072 Pegatron 2011_0107_RT3070_RT3370_Linux_STA_v2.5.0.1_DPO Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: NIvo van Doorn <IvDoorn@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Software scanning can be used for workaround some performance problems, so do not deprecate it. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 3月, 2011 2 次提交
-
-
由 Thomas Gleixner 提交于
Scripted with coccinelle. Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
-
由 Mike Frysinger 提交于
The current code sometimes generates build warnings due to how it checks the silicon revision, so clean it up and properly document things. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-