- 21 6月, 2009 2 次提交
-
-
由 Takashi Iwai 提交于
Add the new model string corresponding to the previous Acer Aspire 6530G support. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Tony Vroon 提交于
The selected 4930G model seemed to keep the subwoofer 'tuba' function from operating correctly. Removing the existing PCI ID match made this work again, but it was mapped to 'Side' instead of to LFE as one would expect. This attempts to enable all functionality and keep the amount of available mixer sliders low. Any slider that had no audible effect on the output audio has been removed, and as such EAPD is not currently enabled. Signed-off-by: NTony Vroon <tony@linx.net> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 17 6月, 2009 3 次提交
-
-
由 Sasha Alexandr 提交于
Correct some trivial typos in comments. Signed-off-by: NSasha Alexandr <brina_keith@ns.sympatico.ca> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Sasha Alexandr 提交于
Correct some cut+paste typos from 'tagra' to 'targa'. Signed-off-by: NSasha Alexandr <brina_keith@ns.sympatico.ca> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Sasha Alexandr 提交于
Add pci-quirk for MSI MS-7350 motherboard with Realtek ALC888. Signed-off-by: NSasha Alexandr <brina_keith@ns.sympatico.ca> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 13 6月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Added model=acer-aspire-8930g for Acer Aspire 6935G (1025:0146). Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 08 6月, 2009 2 次提交
-
-
由 Takashi Iwai 提交于
- Fix a typo in the patch - Adapted to follow the recent change for unsol event handling Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 David Heidelberger 提交于
Added 7.1 support for MSI GX620 and jack quirk. Reference: kernel bug#13430 http://bugzilla.kernel.org/show_bug.cgi?id=13430Signed-off-by: NDavid Heidelberger <d.okias@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 05 6月, 2009 1 次提交
-
-
由 Guido Günther 提交于
with BIOS probing only we offer a non functional headphone swith and volume slider. Signed-off-by: NGuido Günther <agx@sigxcpu.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 04 6月, 2009 1 次提交
-
-
由 Hector Martin 提交于
Enable all three capture channels, including the missing nid 7 which is the only one capable of capturing DMIC input Enable Headphone amp for the HP jack. This causes a volume boost for headphones, but does not cause any noticeable effect for light loads like other amps, so there is no need to make it configurable. Add Input Mix capture mux setting to capture the output of the playback input mux (that is, what goes out the speakers except for PCM) Hack another coef register because the stereo DMIC for some reason produces a nonstandard sum/difference signal. I found a bit to make it just use the sum signal for both channels, which makes it behave like a standard mono microphone. The stereo is useless anyway (they're 1cm apart). Tested working: Three capture channels, mic in, line in, DMIC. Tested not working: CD. Not sure why, might be unconnected in the actual hardware or a CD drive issue. Also looked at SPDIF. It appears to work (emitter lights up inside the HP out jack) but I lack a proper miniTOSLINK cable to test it. Signed-off-by: NHector Martin <hector@marcansoft.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 02 6月, 2009 5 次提交
-
-
由 Hector Martin 提交于
Short story: this laptop has 5.1 built-in speakers which you *really* want to use (the not-so-"sub" woofer is what makes the audio above average for a laptop), so 6-channel support is important (plus a decent asound.conf to upmix stereo). It also has the 3 typical jacks that ought to have a selectable mode. And it's based on ALC889, which sucks. Rationale/explanations: The const_channel_count stuff was added because, for a laptop like this, you always have 6 channels available (internal speakers) but still need to set the mode for the 3 external jacks. Therefore, the device always needs to be in 6-channel mode but there still needs to be a mixer control for the jack mode. You could use line/mic-in at the same time as the 6 internal speakers, for example. You might be tempted to make it even smarter by dynamically switching the max channel count when headphones are plugged in (therefore muting the internal speakers and reducing the physical channel count to the jack channel mode), but as a user I consider this to be harmful because I want the audio to blow up to 6 channels / upmixed as soon as I unplug the headphones, and having opened the device while in 2-channel mode would prevent this from working (and always making 6-channel mode available doesn't do any harm). The hardware needs EAPD turned on and the DACs routed to the internal speaker pins, so the patch adds those verbs. The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work by default, at least here. I wasted much time trying to talk to Realtek/pshou about this, but they just kept sending me useless updates to patch_realtek.c that did nothing relevant. In the end I gave up and brute forced the issue by trying to flip every bit in the proprietary coefficient registers, and eventually found the two magic registers that need to be cleared to enable all DACs. I have only heard Acer users complain, but that might be because ALC889 is pretty new and using 5.1 (and noticing the missing center/lfe channels) might not be that common. If this is a generalized issue with all ALC889 systems then those verbs should probably be moved to a common verb array. The internal mic is untested and probably doesn't work. These settings will probably work for other Acer Gemstone laptops with the same 5.1 speaker config. When identified, those should be added to the PCI subsystem ID list. Signed-off-by: NHector Martin <hector@marcansoft.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Rearrange alc268_cfg_tbl[] in the order of vendor id, and group some entries using SND_PCI_QUIRK_MASK(). Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Ozan Çağlayan 提交于
Currently, LG R510 is only able to produce sound on headphones, the internal speakers are not working. The user tested and confirmed that with model=Dell headphones, internal speakers and the microphone are working flawlessly. Tested-by: NSerdar Soytetir <tulliana@gmail.com> Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kacper Szczesniak 提交于
this is a patch against current snapshot that adds: 6 channels support for the MB5 model Signed-off-by: NKacper Szczesniak <kacper@qwe.pl> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Jaroslav Kysela 提交于
Fix issues for 3 generations of HP workstations. The modest modifications do the following: 1. Change the second MIC from device 3 to device 1 2. Init the "boost" values to "0" by default From: John Brown <john.brown3@hp.com> Signed-off-by: NJaroslav Kysela <perex@perex.cz> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 25 5月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Some Realtek codecs like ALC861 seem to support only VREF50 while the current driver assumes it's only VREF80. Check other VREF bits to set the correct value. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 22 5月, 2009 1 次提交
-
-
由 Adam Williamson 提交于
Fixes https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4121 Taken from https://bugzilla.redhat.com/show_bug.cgi?id=498060Signed-off-by: NAdam Williamson <awilliam@redhat.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 18 5月, 2009 2 次提交
-
-
由 Torben Schulz 提交于
This patch adds support for MacBook 3,1 sound by adding a model new "mb31" with the appropriate init verbs, mixers and channel modes to the ALC883 configuration. patch_alc882() and patch_alc883() are modified to handle the MacBook 3,1 sound-chip (Realtek ALC889A) correctly. Signed-off-by: NTorben Schulz <public@letorbi.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Show the actual chip name in 'unknown model..' info messages for Realtek codecs. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 16 5月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Split the name string in hda_codec struct to vendor_name and chip_name strings to be stored directly from the preset name. Since mostly only the chip name is referred in many patch_*.c, this results in the reduction of many codes in the end. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 15 5月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Added the codec SSID for MacBook Pro 5,1 as compatible as MP51. However, the headphone auto-muting function doesn't work. So, this is just a tentative solution. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 13 5月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
The model=acer for ALC883/889 doesn't work well for the recent Acer Aspire laptops. Since model=auto works better nowadays, it's safer to use the default fallback instead of the Acer specific one. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 12 5月, 2009 1 次提交
-
-
由 Chris Pockelé 提交于
Add specific configuration for Samsung NC10 mini notebook. Internal mic/speakers will be correctly muted when plugging in external ones. Mixer controls are added for speakers, headphones and PC beep. "Boost" is added for the microphones. Signed-off-by: NChris Pockelé <chris.pockele.f1@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 11 5月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Added the missing descriptions and the model names for Realtek codecs to the documentation and the config table. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 08 5月, 2009 3 次提交
-
-
由 Takashi Iwai 提交于
Most of unsol handlers defined in patch_realtek.c can be classified to two types, mute via amp of pins and mute via ctl bits of pins. Thus there are a big room to generalize each implementation. This patch creates two generic functions, alc_automute_amp() and alc_automute_pin(). The latter is actually changed from the previous alc_sku_automute(). Each caller needs to initialize hp_pins and speaker_pins properly at own init_hook. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Just clean up, no functional changes. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The speaker auto-muting per HP plugging for ALC262 HIPPO and compatible devices is slightly buggy as the "Master" or "Front" mixer control can still toggle the speaker output even if the headphone is plugged. This patch fixes the issue, and clean up the hippo-related codes together with fixes of some inconsistent mixer names. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 07 5月, 2009 1 次提交
-
-
由 Kacper Szczesniak 提交于
Signed-off-by: NKacper Szczesniak <kacper@qwe.pl> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 28 4月, 2009 3 次提交
-
-
由 Takashi Iwai 提交于
The commmit dfed0ef9 was reverted accidentally by the merge of auto-detection fix patch. Fixed again now. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Enable auto-muting in model=auto only for devices with HP and speakers. For devices with HP and line-outs, don't enable the auto-muting. Also, add a debug print to show the auto-mute feature. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
In the realtek auto-probing mode, the initialization of amp with some magic COEF or EAPD verbs is applied only when the codec SSID has valid values to satisfy the realtek's definition. However, many devices don't provide in that way, thus the device doesn't work as is. This patch allows the same initialization code even if the SSID doesn't pass the bit test. Also, alc_subsystem_id() is changed just to check and define the type, so that it's called in the parser, instead of the initializer. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 22 4月, 2009 2 次提交
-
-
由 Takashi Iwai 提交于
Added a quirk (model=m51va) for Packard Bell RS65 with ALC663. Reference: Novell bnc#496787 https://bugzilla.novell.com/show_bug.cgi?id=496787Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The NID and ASS numbers were swapped... Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 21 4月, 2009 3 次提交
-
-
由 Takashi Iwai 提交于
Added a couple of debug prints to show the checked id numbers in alc_subsystem_id(). Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
- Support ASUS F81Se F5Q P80 U20A U80 U50 UX50 for ALC269 - Support ASUS F70SL UX20 X58LE F50Z N80Vc N81Te N505Tp Vx3V N5051A for ALC663 - Support DELL ZM1 for ALC272 Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Don't unmute unneeded amps for input mixers of ALC662 & co. It caused possible recording noises. Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 15 4月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Added the models for quirk bitmask 1734:110x and 1734:113x of Fujitsu laptops. This will fix the model detection for Amilo Xa3540. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 06 4月, 2009 1 次提交
-
-
由 Wu Fengguang 提交于
ALC889 has two SPDIF outputs: 0x06, 0x10. Board vendors can use either or both. DX58SO uses 0x10, but the driver assumes 0x06. The safe solution is to add 0x10 as slave output to the existing 0x06. Reported-by: NJeroen Van Breedam <jeroen.vanbreedam@sgr5.be> Tested-by: NJeroen Van Breedam <jeroen.vanbreedam@sgr5.be> Signed-off-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 24 3月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
Add a quirk model=acer-aspire for Acer Ferrari 5000 with ALC883 codec. Note that model=auto doesn't work for this laptop because of broken BIOS (that doesn't set the subsystem id properly). Tested-by: NRuss Dill <russ.dill@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 23 3月, 2009 1 次提交
-
-
由 Takashi Iwai 提交于
In patch_realtek.c, don't create empty or single-item "Input Source" control elements that are simply superfluous. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-