This patch removes the logic previously introduced to address the starvation
on cp_rwsem.

One potential there-in bug is that we should cover the wait.list with spin_lock,
but the previous code broke this rule.

And, actually current rwsem handles this starvation issue reasonably, so that we
didn't need to do this before neither.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

When storing i_rdev, we should check its file type.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

Previously, there was a erroneous scenario like below.
thread 1:                       thread 2:
 f2fs_unlink
  - acquire_orphan_inode
    : sbi->n_orphans++           write_checkpoint
                                 - block_operations
                                  : f2fs_lock_all
                                 - do_checkpoint
                                  : write orphan blocks with sbi->n_orphans
                                 - unblock_operations
  - f2fs_lock_op
  - release_orphan_inode
  - f2fs_unlock_op

During the checkpoint by thread 2, f2fs stores a wrong orphan block according
to the wrong sbi->n_orphans.
To avoid this, simply we should make cover acquire_orphan_inode too with
f2fs_lock_op.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

During the f2fs_put_super procedure, we don't need to conduct checkpoint all
the time, since we don't need to do that if superblock is clean.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

The current f2fs code errors if the xattr or acl options are passed when
remounting.  This is important in a typical scenario where f2fs is mounted
as a "ro" root file-system by the boot loader and then the init process wants
to remount it "rw" with the "remount,rw" option.
Signed-off-by: NKelly Anderson <kelly@xilka.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

The fs_locks is used to block other ops(ex, recovery) when doing checkpoint.
And each other operate routine(besides checkpoint) needs to acquire a fs_lock,
there is a terrible problem here, if these are too many concurrency threads acquiring
fs_lock, so that they will block each other and may lead to some performance problem,
but this is not the phenomenon we want to see.
Though there are some optimization patches introduced to enhance the usage of fs_lock,
but the thorough solution is using a *rw_sem* to replace the fs_lock.
Checkpoint routine takes write_sem, and other ops take read_sem, so that we can block
other ops(ex, recovery) when doing checkpoint, and other ops will not disturb each other,
this can avoid the problem described above completely.
Because of the weakness of rw_sem, the above change may introduce a potential problem
that the checkpoint thread might get starved if other threads are intensively locking
the read semaphore for I/O.(Pointed out by Xu Jin)
In order to avoid this, a wait_list is introduced, the appending read semaphore ops
will be dropped into the wait_list if checkpoint thread is waiting for write semaphore,
and will be waked up when checkpoint thread gives up write semaphore.
Thanks to Kim's previous review and test, and will be very glad to see other guys'
performance tests about this patch.

V2:
  -fix the potential starvation problem.
  -use more suitable func name suggested by Xu Jin.
Signed-off-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: adjust minor coding standard]
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

During recovery, orphan inodes are deleted via truncate_hole().
These orphans are added by recover_dentry() via f2fs_delete_entry().
However, f2fs_delete_entry() adds them via add_orphan_inode()
without calling acquire_orphan_inode() first.  This prevents the
counters from being incremented properly, which causes them to
underflow when remove_orphan_inode() is called later on.
Signed-off-by: NRuss Knize <rknize@motorola.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

f2fs_initxattrs() is called internally from within F2FS and should
not call functions that are used by VFS handlers.  This avoids
certain deadlocks:

- vfs_create()
 - f2fs_create() <-- takes an fs_lock
  - f2fs_add_link()
   - __f2fs_add_link()
    - init_inode_metadata()
     - f2fs_init_security()
      - security_inode_init_security()
       - f2fs_initxattrs()
        - f2fs_setxattr() <-- also takes an fs_lock

If the caller happens to grab the same fs_lock from the pool in both
places, they will deadlock.  There are also deadlocks involving
multiple threads and mutexes:

- f2fs_write_begin()
 - f2fs_balance_fs() <-- takes gc_mutex
  - f2fs_gc()
   - write_checkpoint()
    - block_operations()
     - mutex_lock_all() <-- blocks trying to grab all fs_locks

- f2fs_mkdir() <-- takes an fs_lock
 - __f2fs_add_link()
  - f2fs_init_security()
   - security_inode_init_security()
    - f2fs_initxattrs()
     - f2fs_setxattr()
      - f2fs_balance_fs() <-- blocks trying to take gc_mutex
Signed-off-by: NRuss Knize <Russ.Knize@motorola.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

Accounting errors from buggy code calling the acquire/release/remove
orphan inode interfaces can cause n_orphans to underflow, which will
then cause acquire_orphan_inode() to return -ENOSPC on the next
operation.  This commit guards against that condition.
Signed-off-by: NRuss Knize <rknize@motorola.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

Previously, recover_fsync_data still to write checkpoint when there is
nothing to recover with normal umount image.
It may reduce mount performance and flash memory lifetime, so let's remove
it.
Signed-off-by: NTan Shu <shu.tan@samsung.com>
Signed-off-by: NYu Chao <chao2.yu@samsung.com>
Reviewed-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

This patch add macro MAX_BIO_BLOCKS to limit value of npages in
f2fs_bio_alloc, it can avoid allocating failure in bio_alloc caused by
npages is larger than BIO_MAX_PAGES.
Signed-off-by: NYu Chao <chao2.yu@samsung.com>
Reviewed-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

Since the MAX_VICTIM_SEARCH has been enlarged from 20 to 4096,
the victim searching overhead will be increased much than before,
especially for SSR that searches victim for use quiet often.
This patch intends to reduce the overhead a little bit by:
- make the get_gc_cost a inline routine to reduce function call
  overhead
- reduce multiplication and division operations
- reduce unnecessary comparison operation
Signed-off-by: NJin Xu <jinuxstyle@gmail.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

There is a performance problem: when all sbi->fs_lock are holded, then
all the following threads may get the same next_lock value from sbi->next_lock_num
in function mutex_lock_op, and wait for the same lock(fs_lock[next_lock]),
it may cause performance reduce.
So we move the sbi->next_lock_num++ before getting lock, this will average the
following threads if all sbi->fs_lock are holded.

v1-->v2:
	Drop the needless spin_lock as Jaegeuk suggested.
Suggested-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: NYu Chao <chao2.yu@samsung.com>
Signed-off-by: NGu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

Users have been complaining of the uuid tree stuff warning that there is no uuid
root when trying to do snapshot operations.  This is because if you mount -o ro
we will not create the uuid tree.  But then if you mount -o rw,remount we will
still not create it and then any subsequent snapshot/subvol operations you try
to do will fail gloriously.  Fix this by creating the uuid_root on remount rw if
it was not already there.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

btrfs_ioctl_file_extent_same() uses __put_user_unaligned() to copy some data
back to it's argument struct. Unfortunately, not all architectures provide
__put_user_unaligned(), so compiles break on them if btrfs is selected.

Instead, just copy the whole struct in / out at the start and end of
operations, respectively.
Signed-off-by: NMark Fasheh <mfasheh@suse.de>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Commit 2bc55652 (Btrfs: don't update atime on
RO subvolumes) ensures that the access time of an inode is not updated when
the inode lives in a read-only subvolume.
However, if a directory on a read-only subvolume is accessed, the atime is
updated. This results in a write operation to a read-only subvolume. I
believe that access times should never be updated on read-only subvolumes.

To reproduce:

 # mkfs.btrfs -f /dev/dm-3
 (...)
 # mount /dev/dm-3 /mnt
 # btrfs subvol create /mnt/sub
 	Create subvolume '/mnt/sub'
 # mkdir /mnt/sub/dir
 # echo "abc" > /mnt/sub/dir/file
 # btrfs subvol snapshot -r /mnt/sub /mnt/rosnap
 	Create a readonly snapshot of '/mnt/sub' in '/mnt/rosnap'
 # stat /mnt/rosnap/dir
 	File: `/mnt/rosnap/dir'
 	Size: 8         Blocks: 0          IO Block: 4096   directory
 Device: 16h/22d    Inode: 257         Links: 1
 Access: (0755/drwxr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
 	Access: 2013-09-11 07:21:49.389157126 -0400
 	Modify: 2013-09-11 07:22:02.330156079 -0400
 	Change: 2013-09-11 07:22:02.330156079 -0400
 # ls /mnt/rosnap/dir
 	file
 # stat /mnt/rosnap/dir
 	File: `/mnt/rosnap/dir'
 	Size: 8         Blocks: 0          IO Block: 4096   directory
 Device: 16h/22d    Inode: 257         Links: 1
 Access: (0755/drwxr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
 	Access: 2013-09-11 07:22:56.797151670 -0400
 	Modify: 2013-09-11 07:22:02.330156079 -0400
 	Change: 2013-09-11 07:22:02.330156079 -0400
Reported-by: NKoen De Wit <koen.de.wit@oracle.com>
Signed-off-by: NGuangyu Sun <guangyu.sun@oracle.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

The kernel log entries for device label %s and device fsid %pU
are missing the btrfs: prefix. Add those here.
Signed-off-by: NFrank Holton <fholton@gmail.com>
Reviewed-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

It's still possible to flip the filesystem into RW mode after it's
remounted RO due to an abort. There are lots of places that check for
the superblock error bit and will not write data, but we should not let
the filesystem appear read-write.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This patch makes it possible to set BTRFS_FS_TREE_OBJECTID as the default
subvolume by passing a subvolume id of 0.
Signed-off-by: Nchandan <chandan@linux.vnet.ibm.com>
Reviewed-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

In btrfs_sync_file(), if the call to btrfs_log_dentry_safe() returns
a negative error (for e.g. -ENOMEM via btrfs_log_inode()), we would
return without ending/freeing the transaction.
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

The BUG() was replaced by btrfs_error() and return -EIO with the
patch "get rid of one BUG() in write_all_supers()", but the missing
mutex_unlock() was overlooked.

The 0-DAY kernel build service from Intel reported the missing
unlock which was found by the coccinelle tool:

    fs/btrfs/disk-io.c:3422:2-8: preceding lock on line 3374
Signed-off-by: NStefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

We don't do the iput when we fail to allocate our delayed delalloc work in
__start_delalloc_inodes, fix this.
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This isn't used for anything anymore, just remove it.
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This is a left over of how we used to wait for ordered extents, which was to
grab the inode and then run filemap flush on it.  However if we have an ordered
extent then we already are holding a ref on the inode, and we just use
btrfs_start_ordered_extent anyway, so there is no reason to have an extra ref on
the inode to start work on the ordered extent.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Forever ago I made the worst case calculator say that we could potentially split
into 3 blocks for every level on the way down, which isn't right.  If we split
we're only going to get two new blocks, the one we originally cow'ed and the new
one we're going to split.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This reverts commit 70afa399.  It is causing
performance issues and wasn't actually correct.  There were problems with the
way we flushed delalloc and that was the real cause of the early enospc.
Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Various people have hit a deadlock when running btrfs/011.  This is because when
replacing nocow extents we will take the i_mutex to make sure nobody messes with
the file while we are replacing the extent.  The problem is we are already
holding a transaction open, which is a locking inversion, so instead we need to
save these inodes we find and then process them outside of the transaction.

Further we can't just lock the inode and assume we are good to go.  We need to
lock the extent range and then read back the extent cache for the inode to make
sure the extent really still points at the physical block we want.  If it
doesn't we don't have to copy it.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

So if we have dir_index items in the log that means we also have the inode item
as well, which means that the inode's i_size is correct.  However when we
process dir_index'es we call btrfs_add_link() which will increase the
directory's i_size for the new entry.  To fix this we need to just set the dir
items i_size to 0, and then as we find dir_index items we adjust the i_size.
btrfs_add_link() will do it for new entries, and if the entry already exists we
can just add the name_len to the i_size ourselves.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

A user reported a bug where his log would not replay because he was getting
-EEXIST back.  This was because he had a file moved into a directory that was
logged.  What happens is the file had a lower inode number, and so it is
processed first when replaying the log, and so we add the inode ref in for the
directory it was moved to.  But then we process the directories DIR_INDEX item
and try to add the inode ref for that inode and it fails because we already
added it when we replayed the inode.  To solve this problem we need to just
process any DIR_INDEX items we have in the log first so this all is taken care
of, and then we can replay the rest of the items.  With this patch my reproducer
can remount the file system properly instead of erroring out.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Liu introduced a local copy of the last log commit for an inode to make sure we
actually log an inode even if a log commit has already taken place.  In order to
make sure we didn't relog the same inode multiple times he set this local copy
to the current trans when we log the inode, because usually we log the inode and
then sync the log.  The exception to this is during rename, we will relog an
inode if the name changed and it is already in the log.  The problem with this
is then we go to sync the inode, and our check to see if the inode has already
been logged is tripped and we don't sync the log.  To fix this we need to _also_
check against the roots last log commit, because it could be less than what is
in our local copy of the log commit.  This fixes a bug where we rename a file
into a directory and then fsync the directory and then on remount the directory
is no longer there.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

If you just create a directory and then fsync that directory and then pull the
power plug you will come back up and the directory will not be there.  That is
because we won't actually create directories if we've logged files inside of
them since they will be created on replay, but in this check we will set our
logged_trans of our current directory if it happens to be a directory, making us
think it doesn't need to be logged.  Fix the logic to only do this to parent
directories.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

So forever we have had this thing to limit the amount of delalloc pages we'll
setup to be written out to 128mb.  This is because we have to lock all the pages
in this range, so anything above this gets a bit unweildly, and also without a
limit we'll happily allocate gigantic chunks of disk space.  Turns out our check
for this wasn't quite right, we wouldn't actually limit the chunk we wanted to
write out, we'd just stop looking for more space after we went over the limit.
So if you do a giant 20gb dd on my box with lots of ram I could get 2gig
extents.  This is fine normally, except when you go to relocate these extents
and we can't find enough space to relocate these moster extents, since we have
to be able to allocate exactly the same sized extent to move it around.  So fix
this by actually enforcing the limit.  With this patch I'm no longer seeing
giant 1.5gb extents.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

By the current code, if the requested size is very large, and all the extents
in the free space cache are small, we will waste lots of the cpu time to cut
the requested size in half and search the cache again and again until it gets
down to the size the allocator can return. In fact, we can know the max extent
size in the cache after the first search, so we needn't cut the size in half
repeatedly, and just use the max extent size directly. This way can save
lots of cpu time and make the performance grow up when there are only fragments
in the free space cache.

According to my test, if there are only 4KB free space extents in the fs,
and the total size of those extents are 256MB, we can reduce the execute
time of the following test from 5.4s to 1.4s.
  dd if=/dev/zero of=<testfile> bs=1MB count=1 oflag=sync

Changelog v2 -> v3:
- fix the problem that we skip the block group with the space which is
  less than we need.

Changelog v1 -> v2:
- address the problem that we return a wrong start position when searching
  the free space in a bitmap.
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

We want to know if there are debugging features compiled in, this may
affect performance. The message is printed before the sanity checks.

(This commit message is a copy of David Sterba's commit message when
he introduced btrfs_print_info()).
Signed-off-by: NStefan Behrens <sbehrens@giantdisaster.de>
Reviewed-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Instead of removing the current inode from the red black tree
and then add the new one, just use the red black tree replace
operation, which is more efficient.
Signed-off-by: NFilipe David Borba Manana <fdmanana@gmail.com>
Reviewed-by: NZach Brown <zab@redhat.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

If replace was suspended by the umount, replace target device is added
to the fs_devices->alloc_list during a later mount.  This is obviously
wrong.  ->is_tgtdev_for_dev_replace is supposed to guard against that,
but ->is_tgtdev_for_dev_replace is (and can only ever be) initialized
*after* everything is opened and fs_devices lists are populated.  Fix
this by checking the devid instead: for replace targets it's always
equal to BTRFS_DEV_REPLACE_DEVID.

Cc: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NStefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

If we failed to actually allocate the correct size of the extent to relocate we
will end up in an infinite loop because we won't return an error, we'll just
move on to the next extent.  So fix this up by returning an error, and then fix
all the callers to return an error up the stack rather than BUG_ON()'ing.
Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Don't try to dump the index key that distinguishes an object if netfs
data in the cookie the object refers to has been cleared (ie.  the
cookie has passed most of the way through
__fscache_relinquish_cookie()).

Since the netfs holds the index key, we can't get at it once the ->def
and ->netfs_data pointers have been cleared - and a NULL pointer
exception will ensue, usually just after a:

	CacheFiles: Error: Unexpected object collision

error is reported.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In cachefiles_check_auxdata(), we allocate auxbuf but fail to free it if
we determine there's an error or that the data is stale.

Further, assigning the output of vfs_getxattr() to auxbuf->len gives
problems with checking for errors as auxbuf->len is a u16.  We don't
actually need to set auxbuf->len, so keep the length in a variable for
now.  We shouldn't need to check the upper limit of the buffer as an
overflow there should be indicated by -ERANGE.

While we're at it, fscache_check_aux() returns an enum value, not an
int, so assign it to an appropriately typed variable rather than to ret.
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Hongyi Jia <jiayisuse@gmail.com>
cc: Milosz Tanski <milosz@adfin.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>