Add MMC5 support on PANDA, which has the wl1271 device hardwired to.

The wl1271 is a 4-wire, 1.8V, embedded SDIO WLAN device with an
external IRQ line, and power-controlled by a GPIO-based fixed regulator.

Based on the patch for mmc3/wl1271 device support for zoom by Ohad
Ben-Cohen <ohad@wizery.com>
Signed-off-by: NPanduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a fixed regulator vmmc device to enable power control
of the wl1271 wlan device.

Based on the patch for zoom by Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NPanduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc5 (fifth mmc controller) on the PANDA.

Based on the wlan board muxing for zoom3 by Ohad Ben-Cohen
<ohadb@ti.com>
Signed-off-by: NPanduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixed regulators in twl6030 do not have set_voltage hook.
Regulator core returns -22 if set_voltage is NULL and apply_uV is set
while applying the constraint to set voltage resulting in failure during probe
of these regulators.
Do not set apply_uV for fixed regulators which don't have set_voltage.

machine_constraints_voltage: VANA: failed to apply 2100000uV constraint
twl_reg twl_reg.43: can't register VANA, -22
twl_reg: probe of twl_reg.43 failed with error -22
machine_constraints_voltage: VCXIO: failed to apply 1800000uV constraint
twl_reg twl_reg.44: can't register VCXIO, -22
twl_reg: probe of twl_reg.44 failed with error -22
machine_constraints_voltage: VDAC: failed to apply 1800000uV constraint
twl_reg twl_reg.45: can't register VDAC, -22
twl_reg: probe of twl_reg.45 failed with error -22
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Move non-mapping and non-irq initialization code out of .map_io and
.init_irq respectively into the new init_early hook.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Panda uses both twl6030 otg phy(vbus, id) and internal
phy(data lines, DP/DM), so removes usb_nop_xceiv_register to make
twl6030 otg driver working since current otg code only supports
one global transceiver. Otherwise, musb doesn't work without
the remove.
Reviewd-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The SMSC 3320 USB PHY on the OMAP4 Pandaboard needs a 19.2 MHz
reference clock. This clock is provided from the OMAP4's fref_clk3
pad.

Recent changes to clock44xx_data.c made the clock framework aware
of the existence of these fref_clk[i] lines. If the option
CONFIG_OMAP_RESET_CLOCKS is enabled in the kernel, then the
clock framework will turn these clocks off during bootup.

Explicitly request and keep this clock enabled at init for the
Pandaboard, so that the PHY receives this clock at all times.
Reported-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Split omap2_init_common_hw() into two functions.  The first,
omap2_init_common_infrastructure(), initializes the hwmod code and
data, the OMAP PM code, and the clock code and data.  The second,
omap2_init_common_devices(), handles any other early device
initialization that, for whatever reason, has not been or cannot be
moved to initcalls or early platform devices.

This patch is required for the hwmod postsetup patch, which allows
board files to change the state that hwmods should be placed into at
the conclusion of the hwmod _setup() function.  For example, for a
board whose creators wish to ensure watchdog coverage across the
entire kernel boot process, code to change the watchdog's postsetup
state will be added in the board-*.c file between the
omap2_init_common_infrastructure() and omap2_init_common_devices() function
calls.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>

commit bf56f0a6 (2.6.37-rc1), from Nishanth Menon attempted
to fix card detection for PandaBoard, unfortunately, the fix missed
to initialize .gpio_cd member of omap2_hsmmc_info. This results
in a default value of '0', which is a valid GPIO line.
On PandaBoard, the side effect of this is that GPIO line 0 controls
the powering TFP410 DVI chip, and without the fix DVI chip is
inadvertently powered.
Tested-by: NDavid Anders <x0132446@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NRaghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds omap_reserve functionality to board-omap4panda.c.
Helps in the reserving boot time memory in SDRAM, used here for
framebuffer allocation.

This patch is in similar lines to commit id 71ee7dad, from
Russell king

Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NRaghuveer Murthy <raghuveer.murthy@ti.com>
[tony@atomide.com: fixed to be before .map_io as pointed out by Russell King]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enabling the musb OTG mode for SDP and PANDA boards.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Registering the twl6030-usb transceiver device as a child to twl6030 core.
Removed the NOP transceiver init call from board file.

Populated twl4030_usb_data platform data structure with the function
pointers for OMAP4430 internal PHY operation to be used by twl630-usb driver.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

initialize the musb port on pandaboard.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Implement GPIO as a platform device.

GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.

omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.

Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.

Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.

Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.

Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).

Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.

Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.

In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs

TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
   instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
   to use runtime pm implentation.
Signed-off-by: NCharulatha V <charu@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Reviewed-by: NBasak, Partha <p-basak2@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The mux framework allows the change of pad configuration by drivers
when needed. Prior to this the mux framework has to be initialised
with all the mux parameters specific to the board. The mux init is
already present in the board file for SDP. Adding the mux init
for panda boards.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Acked-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>

For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030. This functionality was introduced in mfd tree on
track to kernel.org

Sync pandaboard to the same and make mmc work.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Tested-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

The OMAP4 PandaBoard has EHCI port1 hooked up to an external
SMSC3320 transciever. GPIO 1 is used to power on the transceiver
and GPIO 62 for reset on the transceiver.
Signed-off-by: NDavid Anders <x0132446@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Avoid possible crash if CONFIG_MMC_OMAP_HS is not set.
Signed-off-by: NDavid Anders <x0132446@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

remove the second hsmmc definition as it is only used on the
expansion header of the PandaBoard and can be mux for other
functions.
Signed-off-by: NDavid Anders <x0132446@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap.  This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.

In response, move the SCM headers into mach-omap2/.

As part of this, remove the direct SCM access from the OMAP UDC
driver.  It was clearly broken.  The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

This patch fixes sparse warnings due non declarations of static functions.

arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: NManjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

At Pandaboard we have 2 status leds, so adding them with similar usage as
we have for Beagleboard (heartbeat and mmc0). The patch basically adds the
platform data required by leds-gpio driver.
Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes these compiler warnings:

  CC      arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function

  CC      arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function

  CC      arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add initial support for the OMAP4 based Panda Board.
Signed-off-by: NDavid Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: NHemanth V <hemanthv@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.

This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Adding support for MMC1 & MMC2 controllers of OMAP4430 SDP
to board file.
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds i2c1 peripherals data to
omap4430 sdp board file.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds the i2c board support for OMAP4430 SDP platform.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable Micrel KS8851 SPI network chip for OMAP4430
Signed-off-by: NAbraham Arce <x0066660@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch moves omap_smc1 function to a seperate omap44xx-smc.S file
and sets compile flags as -Wa,-march=armv7-a.

This fix was suggested by Tony Lindgren <tony@atomide.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: otherwise multi-omap build with V6 and V7 breaks]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The musb support is enabled in omap3 platforms. For omap4 only board
support is available and the driver still isn't supported.
Because of this build with omap3_defconfig used for multi-omap
doesn't work on omap4430 sdp.

This patch avoids usb_musb_init() by adding a cpu check
in the board file.

Thanks to Anand Gadiyar and Mankad Maulik for the suggestion
of patching board file instead of musb driver.
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for Mentor USB to 4430 SDP board
file.

It also defines the base address for HS USB OTG controller
in OMAP4.

Also updates platform specfic structure with base address
and IRQ details.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds L2 Cache support for OMAP4. External L2 cache
is used in OMAP4

CC: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>