CONFIG_X86_CPU_DEBUG, which provides some parsed versions of the x86
CPU configuration via debugfs, has caused boot failures on real
hardware.  The value of this feature has been marginal at best, as all
this information is already available to userspace via generic
interfaces.

Causes crashes that have not been fixed + minimal utility -> remove.

See the referenced LKML thread for more information.
Reported-by: NOzan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
LKML-Reference: <alpine.LFD.2.00.1001221755320.13231@localhost.localdomain>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>

Commit d1c84f79
leads to a regression when microcode_amd.c is compiled into the kernel.
It causes a big boot delay because the firmware is not available.
See http://marc.info/?l=linux-kernel&m=126267290920060

It also renders the reload sysfs attribute useless.
Fixing this is too intrusive for an -rc5 kernel.

Thus I'd like to restore the microcode loading behaviour of kernel
2.6.32.

CC: Gene Heskett <gene.heskett@verizon.net>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100122203456.GB13792@alberich.amd.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

HPET MSI on platforms with ATI SB700/SB800 as they seem to have some
side-effects on floppy DMA. Do not use HPET MSI on such platforms.

Original problem report from Mark Hounschell
http://lkml.indiana.edu/hypermail/linux/kernel/0912.2/01118.html

[ This patch needs to go to stable as well. But, there are some
  conflicts that prevents the patch from going as is. I can
  rebase/resubmit to stable once the patch goes upstream.
  hpa: still Cc:'ing stable@ as an FYI. ]
Tested-by: NMark Hounschell <markh@compro.net>
Signed-off-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
LKML-Reference: <20100121190952.GA32523@linux-os.sc.intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

nodes_possible_map does not currently include nodes that have SRAT
entries that are all ACPI_SRAT_MEM_HOT_PLUGGABLE since the bit is
cleared in nodes_parsed if it does not have an online address range.

Unequivocally setting the bit in nodes_parsed is insufficient since
existing code, such as acpi_get_nodes(), assumes all nodes in the map
have online address ranges.  In fact, all code using nodes_parsed
assumes such nodes represent an address range of online memory.

nodes_possible_map is created by unioning nodes_parsed and
cpu_nodes_parsed; the former represents nodes with online memory and
the latter represents memoryless nodes.  We now set the bit for
hotpluggable nodes in cpu_nodes_parsed so that it also gets set in
nodes_possible_map.

[ hpa: Haicheng Li points out that this makes the naming of the
  variable cpu_nodes_parsed somewhat counterintuitive.  However, leave
  it as is in the interest of keeping the pure bug fix patch small. ]
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Tested-by: NHaicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <alpine.DEB.2.00.1001201152040.30528@chino.kir.corp.google.com>
Cc: <stable@kernel.org>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: x86: Add support for the ANY bit
  perf: Change the is_software_event() definition
  perf: Honour event state for aux stream data
  perf: Fix perf_event_do_pending() fallback callsite
  perf kmem: Print usage help for unknown commands
  perf kmem: Increase "Hit" column length
  hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
  perf timechart: Use tid not pid for COMM change

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
  sched: Fix vmark regression on big machines

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: retry FS IOs even if it has failed with AC_ERR_INVALID

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty: fix race in tty_fasync
  serial: serial_cs: oxsemi quirk breaks resume
  serial: imx: bit &/| confusion
  serial: Fix crash if the minimum rate of the device is > 9600 baud
  serial-core: resume serial hardware with no_console_suspend
  serial: 8250_pnp: use wildcard for serial Wacom tablets
  nozomi: quick fix for the close/close bug
  compat_ioctl: Supress "unknown cmd" message on serial /dev/console

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: hv: fix smp problems in the hyperv core code
  Staging: et131x: Fix 2.6.33rc1 regression in et131x
  Staging: asus_oled: fix oops in 2.6.32.2

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
  driver-core: fix devtmpfs crash on s390

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
  USB: isp1362: better 64bit printf warning fixes
  USB: fix usbstorage for 2770:915d delivers no FAT
  USB: Fix level of isp1760 Reloading ptd error message
  USB: FHCI: avoid NULL pointer dereference
  USB: Fix duplicate sysfs problem after device reset.
  USB: add speed values for USB 3.0 and wireless controllers
  USB: add missing delay during remote wakeup
  USB: EHCI & UHCI: fix race between root-hub suspend and port resume
  USB: EHCI: fix handling of unusual interrupt intervals
  USB: Don't use GFP_KERNEL while we cannot reset a storage device
  USB: fix bitmask merge error
  usb: serial: fix memory leak in generic driver
  USB: serial: fix USB serial fix kfifo_len locking

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  fs/bio.c: fix shadows sparse warning
  drbd: The kernel code is now equivalent to out of tree release 8.3.7
  drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
  drbd: Don't go into StandAlone mode when authentification failes because of network error
  drivers/block/drbd/drbd_receiver.c: correct NULL test
  cfq-iosched: Respect ioprio_class when preempting
  genhd: overlapping variable definition
  block: removed unused as_io_context
  DM: Fix device mapper topology stacking
  block: bdev_stack_limits wrapper
  block: Fix discard alignment calculation and printing
  block: Correct handling of bottom device misaligment
  drbd: check on CONFIG_LBDAF, not LBD
  drivers/block/drbd: Correct NULL test
  drbd: Silenced an assert that could triggered after changing write ordering method
  drbd: Kconfig fix
  drbd: Fix for a race between IO and a detach operation [Bugz 262]
  drbd: Use drbd_crypto_is_hash() instead of an open coded check

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
  ACPI: delete acpi_processor_power_verify_c2()
  ACPI: allow C3 > 1000usec
  ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
  ACPI: power_meter: remove double kfree()
  ACPI: processor: restrict early _PDC to opt-in platforms
  ACPI: Fix unused variable warning in sbs.c
  acpi: make ACPI device id constant
  sony-laptop - fix using of uninitialized variable
  ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
  eeepc-laptop: disable wireless hotplug for 1201N
  eeepc-laptop: add hotplug_disable parameter
  eeepc-laptop: switch to using sparse keymap library
  eeepc-laptop: dmi blacklist to disable pci hotplug code
  eeepc-laptop: disable cpu speed control on EeePC 701
  ACPI: don't cond_resched if irq is disabled
  ACPI: Remove unnecessary cast.
  ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
  ACPI: EC: Add wait for irq storm
  ACPI: SBS: Move SBS HC callback to faster Notify queue
  x86, ACPI: delete acpi_boot_table_init() return value
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  ecryptfs: use after free
  ecryptfs: Eliminate useless code
  ecryptfs: fix interpose/interpolate typos in comments
  ecryptfs: pass matching flags to interpose as defined and used there
  ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
  ecryptfs: don't ignore return value from lock_rename
  ecryptfs: initialize private persistent file before dereferencing pointer
  eCryptfs: Remove mmap from directory operations
  eCryptfs: Add getattr function
  eCryptfs: Use notify_change for truncating lower inodes

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix possible panic on unmount
  Btrfs: deal with NULL acl sent to btrfs_set_acl
  Btrfs: fix regression in orphan cleanup
  Btrfs: Fix race in btrfs_mark_extent_written
  Btrfs, fix memory leaks in error paths
  Btrfs: align offsets for btrfs_ordered_update_i_size
  btrfs: fix missing last-entry in readdir(3)

In free_unmap_area_noflush(), va->flags is marked as VM_LAZY_FREE first, and
then vmap_lazy_nr is increased atomically.

But, in __purge_vmap_area_lazy(), while traversing of vmap_are_list, nr
is counted by checking VM_LAZY_FREE is set to va->flags.  After counting
the variable nr, kernel reads vmap_lazy_nr atomically and checks a
BUG_ON condition whether nr is greater than vmap_lazy_nr to prevent
vmap_lazy_nr from being negative.

The problem is that, if interrupted right after marking VM_LAZY_FREE,
increment of vmap_lazy_nr can be delayed.  Consequently, BUG_ON
condition can be met because nr is counted more than vmap_lazy_nr.

It is highly probable when vmalloc/vfree are called frequently.  This
scenario have been verified by adding delay between marking VM_LAZY_FREE
and increasing vmap_lazy_nr in free_unmap_area_noflush().

Even the vmap_lazy_nr is for checking high watermark, it never be the
strict watermark.  Although the BUG_ON condition is to prevent
vmap_lazy_nr from being negative, vmap_lazy_nr is signed variable.  So,
it could go down to negative value temporarily.

Consequently, removing the BUG_ON condition is proper.

A possible BUG_ON message is like the below.

   kernel BUG at mm/vmalloc.c:517!
   invalid opcode: 0000 [#1] SMP
   EIP: 0060:[<c04824a4>] EFLAGS: 00010297 CPU: 3
   EIP is at __purge_vmap_area_lazy+0x144/0x150
   EAX: ee8a8818 EBX: c08e77d4 ECX: e7c7ae40 EDX: c08e77ec
   ESI: 000081fe EDI: e7c7ae60 EBP: e7c7ae64 ESP: e7c7ae3c
   DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
   Call Trace:
   [<c0482ad9>] free_unmap_vmap_area_noflush+0x69/0x70
   [<c0482b02>] remove_vm_area+0x22/0x70
   [<c0482c15>] __vunmap+0x45/0xe0
   [<c04831ec>] vmalloc+0x2c/0x30
   Code: 8d 59 e0 eb 04 66 90 89 cb 89 d0 e8 87 fe ff ff 8b 43 20 89 da 8d 48 e0 8d 43 20 3b 04 24 75 e7 fe 05 a8 a5 a3 c0 e9 78 ff ff ff <0f> 0b eb fe 90 8d b4 26 00 00 00 00 56 89 c6 b8 ac a5 a3 c0 31
   EIP: [<c04824a4>] __purge_vmap_area_lazy+0x144/0x150 SS:ESP 0068:e7c7ae3c

[ See also http://marc.info/?l=linux-kernel&m=126335856228090&w=2 ]
Signed-off-by: NYongseok Koh <yongseok.koh@samsung.com>
Reviewed-by: NMinchan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh64: wire up sys_accept4.
  sh: unwire sys_recvmmsg.
  sh: ms7724: Correct sh-eth EEPROM polling timeout.

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
  ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
  ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
  ARM: 5884/1: arm: Fix DCC console for v7
  ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
  ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
  ARM: fix badly placed mach/plat entries in Kconfig & Makefile

Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: NStephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Anton reported that perf record kept receiving events even after calling
ioctl(PERF_EVENT_IOC_DISABLE). It turns out that FORK,COMM and MMAP
events didn't respect the disabled state and kept flowing in.
Reported-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: NAnton Blanchard <anton@samba.org>
LKML-Reference: <1263459187.4244.265.camel@laptop>
CC: stable@kernel.org
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Paul questioned the context in which we should call
perf_event_do_pending(). After looking at that I found that it should be
called from IRQ context these days, however the fallback call-site is
placed in softirq context. Ammend this by placing the callback in the IRQ
timer path.
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1263374859.4244.192.camel@laptop>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Assume A->B schedule is processing, if B have acquired BKL before and it
need reschedule this time. Then on B's context, it will go to
need_resched_nonpreemptible for reschedule. But at this time, prev and
switch_count are related to A. It's wrong and will lead to incorrect
scheduler statistics.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <2674af741001102238w7b0ddcadref00d345e2181d11@mail.gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

SD_PREFER_SIBLING is set at the CPU domain level if power saving isn't
enabled, leading to many cache misses on large machines as we traverse
looking for an idle shared cache to wake to.  Change the enabler of
select_idle_sibling() to SD_SHARE_PKG_RESOURCES, and enable same at the
sibling domain level.
Reported-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NMike Galbraith <efault@gmx.de>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1262612696.15495.15.camel@marge.simson.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

There was some left over #ifdef ARM logic that is outdated but no one
really noticed.  So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings.  So use %zu for sizeof() values.  This is a
better version of the previous commit b0a9cf29.
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Resolves kernel.org bug 14914.

Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).

The patch works, but let me clarify a few things about it.  All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think).  I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear.  Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine.  Starting with
2.6.30, things no longer work.
Signed-off-by: NRyan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Assign fhci only if usb is not NULL.
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate.  It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:

[  427.681810] Restarting tasks ...
[  427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[  427.682019] usb usb3: usb resume
[  427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[  427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[  427.682205] usb 1-2: usb wakeup-resume
[  427.682226] usb 1-2: finish reset-resume
[  427.682886] done.
[  427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[  427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[  427.746682] hub 3-0:1.0: hub_reset_resume
[  427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[  427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[  427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[  427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[  427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[  427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[  427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[  427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[  427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[  427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[  427.916609]  ep_81: create, parent hub
[  427.916632] ------------[ cut here ]------------
[  427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[  427.916649] Hardware name: System Product Name
[  427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[  427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[  427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869aa-dirty #13
[  427.916699] Call Trace:

The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.

After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces.  However, the
USB core keeps track of the old state, which may include non-zero
alternate settings.  It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.

The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0.  This caused duplicate
endpoint files to be created.

The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device().  Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NBorislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: NKurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1330) fixes a bug in khbud's handling of remote
wakeups.  When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes.  At
this point the port's SUSPEND feature is automatically turned off.

However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec).  Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup.  This patch adds the missing
delay to the remote-wakeup path.

It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes).  The extra time appears to help some
devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost.  When remote wakeup is
enabled, this is undesirable behavior.

The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.

	URBs with an interval of 2 or 4 microframes aren't handled.
	For the time being, the patch reduces to interval to 1 uframe.

	URBs are constrained to have an interval no larger than 1024
	frames by usb_submit_urb().  But some EHCI controllers allow
	use of a schedule as short as 256 frames; for these
	controllers we may have to decrease the interval to the
	actual schedule length.

The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames.  But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: NGlynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a regression introduced by commit
715b1dc0 ("USB: usb_debug,
usb_generic_serial: implement multi urb write").

URB transfer buffer was never freed when using multi-urb writes. 
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: NJason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.

Please apply it to the 2.6.33-rc* tree.
Signed-off-by: NStefani Seibold <stefani@seibold.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a number of SMP problems that were in the hyperv core code.

Patch originally written by K. Y. Srinivasan <ksrinivasan@novell.com>
but forward ported to the latest in-kernel code and tweaked slightly by
me.

Novell, Inc. hereby disclaims all copyright in any derivative work
copyright associated with this patch.
Signed-off-by: NK. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>.
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>