Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs.  This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NMichael Büsch <m@bues.ch>
Tested-by: NMichael Büsch <m@bues.ch>
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.16-rc4

A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.

CPPI41 got a race condition fix which was found by Thomas Gleixner.

The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.

We also have a fix for a panic caused when removing musb_am335x driver.

Other than that, a few other minor fixes.
Signed-of-by: NFelipe Balbi <balbi@ti.com>

commit 943c1397 "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format.  Fix by wrapping the numbers in
cpu_to_le32.

Cc: stable@vger.kernel.org
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use case is when the phy is configured in host mode and a usb device is
attached to board before bootup. On bootup, with the existing code and
runtime pm enabled, the driver would decrement the pm usage count
without checking the current state of the phy. This pm usage count
decrement would trigger the runtime pm which than would abort the
usb enumeration which was in progress. In my case a usb stick gets
detected and then immediatly the driver goes to low power mode which is
not correct.

log:
[    1.631412] msm_hsusb_host 12520000.usb: EHCI Host Controller
[    1.636556] msm_hsusb_host 12520000.usb: new USB bus registered, assigned bus number 1
[    1.642563] msm_hsusb_host 12520000.usb: irq 220, io mem 0x12520000
[    1.658197] msm_hsusb_host 12520000.usb: USB 2.0 started, EHCI 1.00
[    1.659473] hub 1-0:1.0: USB hub found
[    1.663415] hub 1-0:1.0: 1 port detected
...
[    1.973352] usb 1-1: new high-speed USB device number 2 using msm_hsusb_host
[    2.107707] usb-storage 1-1:1.0: USB Mass Storage device detected
[    2.108993] scsi0 : usb-storage 1-1:1.0
[    2.678341] msm_otg 12520000.phy: USB in low power mode
[    3.168977] usb 1-1: USB disconnect, device number 2

This issue was detected on IFC6410 board.

This patch fixes the intial runtime pm trigger by checking the phy
state and decrementing the pm use count only when the phy state is IDLE.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Merge tag 'usb-serial-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v3.16-rc3

Here are some USB-serial updates for v3.16-rc3 that fix a reported
NULL-pointer dereference and add some new device IDs.

Included is also two changes to MAINTAINERS dropping individual
maintainership for two small sub-drivers and updating an email address.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:

CPU 0					CPU1

start_next_transfer(RQ1);

DMA interrupt
  if (premature_irq(RQ1))
    if (!hrtimer_active(timer))
       hrtimer_start(timer);

hrtimer expires
  timer->state = CALLBACK_RUNNING;
  timer->fn()
    cppi41_recheck_tx_req()
      complete_request(RQ1);
      if (requests_pending())
        start_next_transfer(RQ2);

					DMA interrupt
					  if (premature_irq(RQ2))
					    if (!hrtimer_active(timer))
					       hrtimer_start(timer);
  timer->state = INACTIVE;

The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:

  timer->state != HRTIMER_STATE_INACTIVE

which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.

That's clearly documented:

 * A timer is active, when it is enqueued into the rbtree or the
 * callback function is running or it's in the state of being migrated
 * to another cpu.

But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.

We have a helper function for this: hrtimer_is_queued(). This
evaluates:

  timer->state & HRTIMER_STATE_QUEUED

So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().

Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: NTorben Hohn <torbenh@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The value 0x3 (not 0x11) in the field for additional transaction/microframe
is reserved and should not be let through. Be clear in the error message about
what value caused the error return.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NAndreas Larsson <andreas@gaisler.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

At probe time, the musb_am335x driver register its childs by
calling of_platform_populate(), which registers all childs in
the devicetree hierarchy recursively.

On the other side, the driver's remove() function uses of_device_unregister()
to remove each child of musb_am335x's.

However, when musb_dsps is loaded, its devices are attached to the musb_am335x
device as musb_am335x childs. Hence, musb_am335x remove() will attempt to
unregister the devices registered by musb_dsps, which produces a kernel panic.

In other words, the childs in the "struct device" hierarchy are not the same
as the childs in the "devicetree" hierarchy.

Ideally, we should enforce the removal of the devices registered by
musb_am335x *only*, instead of all its child devices. However, because of the
recursive nature of of_platform_populate, this doesn't seem possible.

Therefore, as the only solution at hand, this commit disables musb_am335x
driver removal capability, preventing it from being ever removed. This was
originally suggested by Sebastian Siewior:

https://www.mail-archive.com/linux-omap@vger.kernel.org/msg104946.html

And for reference, here's the panic upon module removal:

musb-hdrc musb-hdrc.0.auto: remove, state 4
usb usb1: USB disconnect, device number 1
musb-hdrc musb-hdrc.0.auto: USB bus 1 deregistered
Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = de11c000
[0000008c] *pgd=9e174831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] ARM
Modules linked in: musb_am335x(-) musb_dsps musb_hdrc usbcore usb_common
CPU: 0 PID: 623 Comm: modprobe Not tainted 3.15.0-rc4-00001-g24efd13 #69
task: de1b7500 ti: de122000 task.ti: de122000
PC is at am335x_shutdown+0x10/0x28
LR is at am335x_shutdown+0xc/0x28
pc : [<c0327798>]    lr : [<c0327794>]    psr: a0000013
sp : de123df8  ip : 00000004  fp : 00028f00
r10: 00000000  r9 : de122000  r8 : c000e6c4
r7 : de0e3c10  r6 : de0e3800  r5 : de624010  r4 : de1ec750
r3 : de0e3810  r2 : 00000000  r1 : 00000001  r0 : 00000000
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c5387d  Table: 9e11c019  DAC: 00000015
Process modprobe (pid: 623, stack limit = 0xde122240)
Stack: (0xde123df8 to 0xde124000)
3de0:                                                       de0e3810 bf054488
3e00: bf05444c de624010 60000013 bf043650 000012fc de624010 de0e3810 bf043a20
3e20: de0e3810 bf04b240 c0635b88 c02ca37c c02ca364 c02c8db0 de1b7500 de0e3844
3e40: de0e3810 c02c8e28 c0635b88 de02824c de0e3810 c02c884c de0e3800 de0e3810
3e60: de0e3818 c02c5b20 bf05417c de0e3800 de0e3800 c0635b88 de0f2410 c02ca838
3e80: bf05417c de0e3800 bf055438 c02ca8cc de0e3c10 bf054194 de0e3c10 c02ca37c
3ea0: c02ca364 c02c8db0 de1b7500 de0e3c44 de0e3c10 c02c8e28 c0635b88 de02824c
3ec0: de0e3c10 c02c884c de0e3c10 de0e3c10 de0e3c18 c02c5b20 de0e3c10 de0e3c10
3ee0: 00000000 bf059000 a0000013 c02c5bc0 00000000 bf05900c de0e3c10 c02c5c48
3f00: de0dd0c0 de1ec970 de0f2410 bf05929c de0f2444 bf05902c de0f2410 c02ca37c
3f20: c02ca364 c02c8db0 bf05929c de0f2410 bf05929c c02c94c8 bf05929c 00000000
3f40: 00000800 c02c8ab4 bf0592e0 c007fc40 c00dd820 6273756d 336d615f 00783533
3f60: c064a0ac de1b7500 de122000 de1b7500 c000e590 00000001 c000e6c4 c0060160
3f80: 00028e70 00028e70 00028ea4 00000081 60000010 00028e70 00028e70 00028ea4
3fa0: 00000081 c000e500 00028e70 00028e70 00028ea4 00000800 becb59f8 00027608
3fc0: 00028e70 00028e70 00028ea4 00000081 00000001 00000001 00000000 00028f00
3fe0: b6e6b6f0 becb59d4 000160e8 b6e6b6fc 60000010 00028ea4 00000000 00000000
[<c0327798>] (am335x_shutdown) from [<bf054488>] (dsps_musb_exit+0x3c/0x4c [musb_dsps])
[<bf054488>] (dsps_musb_exit [musb_dsps]) from [<bf043650>] (musb_shutdown+0x80/0x90 [musb_hdrc])
[<bf043650>] (musb_shutdown [musb_hdrc]) from [<bf043a20>] (musb_remove+0x24/0x68 [musb_hdrc])
[<bf043a20>] (musb_remove [musb_hdrc]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c8e28>] (device_release_driver+0x20/0x2c)
[<c02c8e28>] (device_release_driver) from [<c02c884c>] (bus_remove_device+0xdc/0x10c)
[<c02c884c>] (bus_remove_device) from [<c02c5b20>] (device_del+0x104/0x198)
[<c02c5b20>] (device_del) from [<c02ca838>] (platform_device_del+0x14/0x9c)
[<c02ca838>] (platform_device_del) from [<c02ca8cc>] (platform_device_unregister+0xc/0x20)
[<c02ca8cc>] (platform_device_unregister) from [<bf054194>] (dsps_remove+0x18/0x38 [musb_dsps])
[<bf054194>] (dsps_remove [musb_dsps]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c8e28>] (device_release_driver+0x20/0x2c)
[<c02c8e28>] (device_release_driver) from [<c02c884c>] (bus_remove_device+0xdc/0x10c)
[<c02c884c>] (bus_remove_device) from [<c02c5b20>] (device_del+0x104/0x198)
[<c02c5b20>] (device_del) from [<c02c5bc0>] (device_unregister+0xc/0x20)
[<c02c5bc0>] (device_unregister) from [<bf05900c>] (of_remove_populated_child+0xc/0x14 [musb_am335x])
[<bf05900c>] (of_remove_populated_child [musb_am335x]) from [<c02c5c48>] (device_for_each_child+0x44/0x70)
[<c02c5c48>] (device_for_each_child) from [<bf05902c>] (am335x_child_remove+0x18/0x30 [musb_am335x])
[<bf05902c>] (am335x_child_remove [musb_am335x]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c94c8>] (driver_detach+0xb4/0xb8)
[<c02c94c8>] (driver_detach) from [<c02c8ab4>] (bus_remove_driver+0x4c/0xa0)
[<c02c8ab4>] (bus_remove_driver) from [<c007fc40>] (SyS_delete_module+0x128/0x1cc)
[<c007fc40>] (SyS_delete_module) from [<c000e500>] (ret_fast_syscall+0x0/0x48)

Fixes: 97238b35 ("usb: musb: dsps: use proper child nodes")
Cc: <stable@vger.kernel.org> # v3.12+
Acked-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Even though usb_functionfs_descs_head structure is now deprecated,
it has been used by some user space tools.  Its removel in commit
[ac8dde11: “Add flags to descriptors block”] was an oversight
leading to build breakage for such tools.

Bring it back so that old user space tools can still be build
without problems on newer kernel versions.

Cc: <stable@vger.kernel.org>  # 3.14
Reported-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Reported-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This reverts commit f2af7412.

There is a better fix for this build error coming in a following
patch.
Signed-of-by: NFelipe Balbi <balbi@ti.com>

The system suspend flow as following:
1, Freeze all user processes and kenrel threads.

2, Try to suspend all devices.

2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.

2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.

2.3, Call suspend callbacks of devices.

2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.

2.3.2, Finally, hcd_pci_suspend callback is called.

Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.

The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.

For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.

xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.

This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120
"USB: XHCI: resume root hubs when the controller resumes"

Cc: stable@vger.kernel.org # 3.2
Signed-off-by: NWang, Yu <yu.y.wang@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
[use readl() instead of removed xhci_readl(), reword commit message -Mathias]
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When xHCI PCI host is suspended, if do_wakeup is false in xhci_pci_suspend,
xhci_bus_suspend needs to clear all root port wake on bits. Otherwise some Intel
platforms may get a spurious wakeup, even if PCI PME# is disabled.

This patch should be back-ported to kernels as old as 2.6.37, that
contains the commit 9777e3ce
"USB: xHCI: bus power management implementation".

Cc: stable@vger.kernel.org # 2.6.37
Signed-off-by: NLu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).

Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1

This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33
"xhci 1.0: Set transfer burst count field."

Cc: stable@vger.kernel.org # 3.0
Suggested-by: NShiChun Ma <masc2008@qq.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Command completion events normally include command completion status,
SLOT_ID, and a pointer to the original command. Reset device command
completion SLOT_ID may be zero according to xhci specs 4.6.11.

VIA controllers set the SLOT_ID to zero, triggering a WARN_ON in the
command completion handler.

Use the SLOT ID found from the original command instead.

This patch should be applied to stable kernels since 3.13 that contain
the commit 20e7acb1
"xhci: use completion event's slot id rather than dig it out of command"

Cc: stable@vger.kernel.org # 3.13
Reported-by: NSaran Neti <sarannmr@gmail.com>
Tested-by: NSaran Neti <sarannmr@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'fixes-for-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

usb: fixes for v3.16-rc2

dwc3-omap won't crash anymore on module removal and suspend/resume won't kill
xHCI interrupts.

MUSB got a fix to handle Babble condition only in host mode, how it should be.

The f_fs function driver got a fix for a NULL pointer dereference.

Renesas gadget got a fix for Status stage handling.
Signed-of-by: NFelipe Balbi <balbi@ti.com>

I'll be using my kernel.org address for upstream work from now on so
update my MAINTAINERS entry.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Adding a couple of Olivetti modems and blacklisting the net
function on a couple which are already supported.
Reported-by: NLars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Fix NULL-pointer dereference when probing an interface with no
endpoints.

These devices have two bulk endpoints per interface, but this avoids
crashing the kernel if a user forces a non-FTDI device to be probed.

Note that the iterator variable was made unsigned in order to avoid
a maybe-uninitialized compiler warning for ep_desc after the loop.

Fixes: 895f28ba ("USB: ftdi_sio: fix hi-speed device packet size
calculation")
Reported-by: NMike Remski <mremski@mutualink.net>
Tested-by: NMike Remski <mremski@mutualink.net>
Cc: <stable@vger.kernel.org>	# 2.6.31
Signed-off-by: NJohan Hovold <johan@kernel.org>

Remove the remaining two obsolete usb-serial subdriver entries from
MAINTAINERS, which were missed in the recent purge by commit
f896b796 ("USB: Maintainers change for usb serial drivers").
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>

Reported by Alif Mubarak Ahmad:

This device vendor and product id is 1c9e:9800
It is working as serial interface with generic usbserial driver.
I thought it is more suitable to use usbserial option driver, which has
better capability distinguishing between modem serial interface and
micro sd storage interface.

[ johan: style changes ]
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Tested-by: NAlif Mubarak Ahmad <alive4ever@live.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Pull i2c new drivers from Wolfram Sang:
 "Here is a pull request from i2c hoping for the "new driver" rule.

  Originally, I wanted to send this request during the merge window, but
  code checkers with very recent additions complained, so a few fixups
  were needed.  So, some more time went by and I merged rc1 to get a
  stable base"

So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c.  So I considered not pulling this, but eventually
relented.

Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.

So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: sun6-p2wi: fix call to snprintf
  i2c: rk3x: add NULL entry to the end of_device_id array
  i2c: sun6i-p2wi: use proper return value in probe
  i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
  i2c: sunxi: add P2WI DT bindings documentation
  i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter

Pull file locking fixes from Jeff Layton:
 "File locking related bugfixes

  Nothing too earth-shattering here.  A fix for a potential regression
  due to a patch in pile #1, and the addition of a memory barrier to
  prevent a race condition between break_deleg and generic_add_lease"

* tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux:
  locks: set fl_owner for leases back to current->files
  locks: add missing memory barrier in break_deleg

Pull kbuild fixes from Michal Marek:
 "There are three fixes for regressions caused by the relative paths
  series: deb-pkg, tar-pkg and *docs did not work with O=.

  Plus, there is a fix for the linux-headers deb package and a fixed
  typo.  These are not regression fixes but are safe enough"

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: fix a typo in a kbuild document
  builddeb: fix missing headers in linux-headers package
  Documentation: Fix DocBook build with relative $(srctree)
  kbuild: Fix tar-pkg with relative $(objtree)
  deb-pkg: Fix for relative paths

Pull btrfs fixes from Chris Mason:
 "This fixes some lockups in btrfs reported with rc1.  It probably has
  some performance impact because it is backing off our spinning locks
  more often and switching to a blocking lock.  I'll be able to nail
  that down next week, but for now I want to get the lockups taken care
  of.

  Otherwise some more stack reduction and assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix wrong error handle when the device is missing or is not writeable
  Btrfs: fix deadlock when mounting a degraded fs
  Btrfs: use bio_endio_nodec instead of open code
  Btrfs: fix NULL pointer crash when running balance and scrub concurrently
  btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
  Btrfs: fix broken free space cache after the system crashed
  Btrfs: make free space cache write out functions more readable
  Btrfs: remove unused wait queue in struct extent_buffer
  Btrfs: fix deadlocks with trylock on tree nodes

Pull nfsd bugfixes from Bruce Fields:
 "Fixes for a new regression from the xdr encoding rewrite, and a
  delegation problem we've had for a while (made somewhat more annoying
  by the vfs delegation support added in 3.13)"

* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
  NFSD: fix bug for readdir of pseudofs
  NFSD: Don't hand out delegations for 30 seconds after recalling them.

Pull perf fixes from Ingo Molnar:
 "This is larger than usual: the main reason are the ARM symbol lookup
  speedups that came in late and were hard to resist.

  There's also a kprobes fix and various tooling fixes, plus the minimal
  re-enablement of the mmap2 support interface"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  x86/kprobes: Fix build errors and blacklist context_track_user
  perf tests: Add test for closing dso objects on EMFILE error
  perf tests: Add test for caching dso file descriptors
  perf tests: Allow reuse of test_file function
  perf tests: Spawn child for each test
  perf tools: Add dso__data_* interface descriptons
  perf tools: Allow to close dso fd in case of open failure
  perf tools: Add file size check and factor dso__data_read_offset
  perf tools: Cache dso data file descriptor
  perf tools: Add global count of opened dso objects
  perf tools: Add global list of opened dso objects
  perf tools: Add data_fd into dso object
  perf tools: Separate dso data related variables
  perf tools: Cache register accesses for unwind processing
  perf record: Fix to honor user freq/interval properly
  perf timechart: Reflow documentation
  perf probe: Improve error messages in --line option
  perf probe: Improve an error message of perf probe --vars mode
  perf probe: Show error code and description in verbose mode
  perf probe: Improve error message for unknown member of data structure
  ...

Merge branch 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull rtmutex fixes from Thomas Gleixner:
 "Another three patches to make the rtmutex code more robust.  That's
  the last urgent fallout from the big futex/rtmutex investigation"

* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rtmutex: Plug slow unlock race
  rtmutex: Detect changes in the pi lock chain
  rtmutex: Handle deadlock detection smarter

Pull s390 patches from Martin Schwidefsky:
 "A couple of bug fixes, a debug change for qdio, an update for the
  default config, and one small extension.

  The watchdog module based on diagnose 0x288 is converted to the
  watchdog API and it now works under LPAR as well"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ccwgroup: use ccwgroup_ungroup wrapper
  s390/ccwgroup: fix an uninitialized return code
  s390/ccwgroup: obtain extra reference for asynchronous processing
  qdio: Keep device-specific dbf entries
  s390/compat: correct ucontext layout for high gprs
  s390/cio: set device name as early as possible
  s390: update default configuration
  s390: avoid format strings leaking into names
  s390/airq: silence lockdep warning
  s390/watchdog: add support for LPAR operation (diag288)
  s390/watchdog: use watchdog API
  s390/sclp_vt220: Enable ASCII console per default
  s390/qdio: replace shift loop by ilog2
  s390/cio: silence lockdep warning
  s390/uaccess: always load the kernel ASCE after task switch
  s390/ap_bus: Make modules parameters visible in sysfs

Pull UniCore32 bug fixes from Guan Xuetao:
 "This includes bugfixes to make unicore32 successfully build under
  defconfig, and some changes for allmodconfig (though not finished)"

* tag 'for-linus' of git://github.com/gxt/linux:
  unicore32: Remove ARCH_HAS_CPUFREQ config option
  UniCore32: Change git tree location information in MAINTAINERS
  arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
  arch: unicore32: ksyms: export 'pm_power_off' to avoid compiling failure.
  arch: unicore32: ksyms: export additional find_first_*() to avoid compiling failure
  arch:unicore32:mm: add devmem_is_allowed() to support STRICT_DEVMEM
  unicore32: include: asm: add missing ')' for PAGE_* macros in pgtable.h
  arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
  drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
  arch: unicore32: kernel: ksyms: remove 'bswapsi2' and 'muldi3' to avoid compiling failure
  arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
  drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
  drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
  arch/unicore32/include/asm/io.h: add readl_relaxed() generic definition
  arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
  arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
  arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
  arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
  arch/unicore32/kernel/ksyms.c: remove several undefined exported symbols

Pull char / misc driver fixes from Greg KH:
 "Here are 3 patches, one a revert of the UIO patch you objected to in
  3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
  MAINTAINERS update for the vmware balloon driver.

  All of these, except for the MAINTAINERS update which just got added,
  have been in linux-next just fine"

* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: add entry for VMware Balloon driver
  w1: mxc_w1: Fix incorrect "presence" status
  Revert "uio: fix vma io range check in mmap"

Pull staging driver fixes from Greg KH:
 "Here are a few fixes for staging and iio drivers that resolve issues
  reported in 3.16-rc1.

  All have been in linux-next just fine"

* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  imx-drm: parallel-display: Fix DPMS default state.
  staging: android: timed_output: fix use after free of dev
  staging: comedi: addi_apci_1564: add addi_watchdog dependency
  staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
  staging: rtl8723au: Request correct firmware file for A-cut parts
  iio: adc: checking for NULL instead of IS_ERR() in probe
  iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
  iio: mxs-lradc: fix divider
  iio: Fix endianness issue in ak8975_read_axis()
  staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
  twl4030-madc: Request processed values in twl4030_get_madc_conversion
  staging: iio: tsl2x7x_core: fix proximity treshold
  iio: Fix two mpl3115 issues in measurement conversion
  iio: hid-sensors: Get feature report from sensor hub after changing power state

Pull tty/serial bugfixes from Greg KH:
 "Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
  some reported issues.  The samsung driver build error itself has been
  reported by a bunch of people, sorry about that one.  The others are
  all tiny and everyone seems to like them in linux-next so far"

* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty/serial: fix 8250 early console option passing to regular console
  tty: Correct INPCK handling
  serial: Fix IGNBRK handling
  serial: samsung: Fix build error

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 3.16-rc2 that resolve some reported
  issues.  All of these have been in linux-next for a while with no
  problems"

* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: usbtest: add a timeout for scatter-gather tests
  USB: EHCI: avoid BIOS handover on the HASEE E200
  usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
  usb: quiet peer failure warning, disable poweroff
  usb: improve "not suspended yet" message in hub_suspend()
  xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
  usb: fix ->update_hub_device() vs hdev->maxchild

Signed-off-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are fixes mostly (ia64 regression related to the ACPI
  enumeration of devices, cpufreq regressions, fix for I2C controllers
  included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
  plus additional kernel command line arguments from Kees to make it
  possible to build kernel images with hibernation and the kernel
  address space randomization included simultaneously, a new ACPI
  battery driver quirk for a system with a broken BIOS and a couple of
  ACPI core cleanups.

  Specifics:

   - Fix for an ia64 regression introduced during the 3.11 cycle by a
     commit that modified the hardware initialization ordering and made
     device discovery fail on some systems.

   - Fix for a build problem on systems where the cpufreq-cpu0 driver is
     built-in and the cpu-thermal driver is modular from Arnd Bergmann.

   - Fix for a recently introduced computational mistake in the
     intel_pstate driver that leads to excessive rounding errors from
     Doug Smythies.

   - Fix for a failure code path in cpufreq_update_policy() that fails
     to unlock the locks acquired previously from Aaron Plattner.

   - Fix for the cpuidle mvebu driver to use shorter state names which
     will prevent the sysfs interface from returning mangled strings.
     From Gregory Clement.

   - ACPI LPSS driver fix to make sure that the I2C controllers included
     in BayTrail SoCs are not held in the reset state while they are
     being probed from Mika Westerberg.

   - New kernel command line arguments making it possible to build
     kernel images with hibernation and kASLR included at the same time
     and to select which of them will be used via the command line (they
     are still functionally mutually exclusive, though).  From Kees
     Cook.

   - ACPI battery driver quirk for Acer Aspire V5-573G that fails to
     send battery status change notifications timely from Alexander
     Mezin.

   - Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"

* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: mvebu: Fix the name of the states
  cpufreq: unlock when failing cpufreq_update_policy()
  intel_pstate: Correct rounding in busy calculation
  ACPI: use kstrto*() instead of simple_strto*()
  ACPI / processor replace __attribute__((packed)) by __packed
  ACPI / battery: add quirk for Acer Aspire V5-573G
  ACPI / battery: use callback for setting up quirks
  ACPI / LPSS: Take I2C host controllers out of reset
  x86, kaslr: boot-time selectable with hibernation
  PM / hibernate: introduce "nohibernate" boot parameter
  cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
  ACPI / ia64 / sba_iommu: Restore the working initialization ordering

Pull sound fixes from Takashi Iwai:
 "The significant part here is a few security fixes for ALSA core
  control API by Lars.  Besides that, there are a few fixes for ASoC
  sigmadsp (again by Lars) for building properly, and small fixes for
  ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
  i915/HD-audio binding"

* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: control: Make sure that id->index does not overflow
  ALSA: control: Handle numid overflow
  ALSA: control: Don't access controls outside of protected regions
  ALSA: control: Fix replacing user controls
  ALSA: control: Protect user controls against concurrent access
  drm/i915, HD-audio: Don't continue probing when nomodeset is given
  ASoC: fsl: Fix build problem
  ASoC: rsnd: fixup index of src/dst mod when capture
  ASoC: fsl_spdif: Fix integer overflow when calculating divisors
  ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
  ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
  ASoC: sigmadsp: Split regmap and I2C support into separate modules
  ASoC: MMP audio needs sram support
  ASoC: pxa: add I2C dependencies as needed

Pull drm fixes from Dave Airlie:
 "This looks bigger than it is, as one of the nouveau firmware fixes
  ("drm/gf100-/gr: report class data to host on fwmthd failure")
  regenerates a bunch of the firmware files after changing the assembly
  by a few lines, without that, its more of a

    36 files changed, 370 insertions(+), 129 deletions(-)

  It contains some vt.c fixes acked by Greg, for rare hard hangs on i915
  loading, that also fixes hangs on reload and spurious register write
  errors.

  drm core: one fix for uninit memory

  nouveau: displayport rework caused a few regressions, Ben has been
     fixing them as the appear, along with some other fixes

  radeon: pageflipping regression fix, deep color fix, mode validation
     fixes

  i915: fbc disable, vga console kick off, backlight fix, divide-by-zero
     fix"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
  drm: fix uninitialized acquire_ctx fields (v2)
  drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
  Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
  drm/radeon: improve dvi_mode_valid
  drm/radeon: update mode_valid testing for DP
  drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
  drm/nouveau/disp: fix oops in destructor with headless cards
  drm/gf117/i2c: no aux channels on this chipset
  drm/nouveau/doc: update the thermal documentation
  drm/nouveau/pwr: fix typo in fifo wrap handling
  drm/nv50/disp: fix a potential oops in supervisor handling
  drm/nouveau/disp/dp: don't touch link config after success
  drm/nouveau/kms: reference vblank for crtc during pageflip.
  drm/gk104/fb/ram: fixups from an earlier search+replace
  drm/nv50/gr: remove an unneeded write while initialising PGRAPH
  drm/nv50/gr: fix overlap while zeroing zcull regions
  drm/gf100-/gr: report class data to host on fwmthd failure
  drm/gk104/ibus: increase various random timeouts
  drm/gk104/clk: only touch divider for mode we'll be using
  drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
  ...

Pull block fixes from Jens Axboe:
 "A smaller collection of fixes for the block core that would be nice to
  have in -rc2.  This pull request contains:

   - Fixes for races in the wait/wakeup logic used in blk-mq from
     Alexander.  No issues have been observed, but it is definitely a
     bit flakey currently.  Alternatively, we may drop the cyclic
     wakeups going forward, but that needs more testing.

   - Some cleanups from Christoph.

   - Fix for an oops in null_blk if queue_mode=1 and softirq completions
     are used.  From me.

   - A fix for a regression caused by the chunk size setting.  It
     inadvertently used max_hw_sectors instead of max_sectors, which is
     incorrect, and causes hangs on btrfs multi-disk setups (where hw
     sectors apparently isn't set).  From me.

   - Removal of WQ_POWER_EFFICIENT in the kblockd creation.  This was a
     recent addition as well, but it actually breaks blk-mq which relies
     on strict scheduling.  If the workqueue power_efficient mode is
     turned on, this breaks blk-mq.  From Matias.

   - null_blk module parameter description fix from Mike"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: bitmap tag: fix races in bt_get() function
  blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
  blk-mq: bitmap tag: fix races on shared ::wake_index fields
  block: blk_max_size_offset() should check ->max_sectors
  null_blk: fix softirq completions for queue_mode == 1
  blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
  blk-mq: properly drain stopped queues
  block: remove WQ_POWER_EFFICIENT from kblockd
  null_blk: fix name and description of 'queue_mode' module parameter
  block: remove elv_abort_queue and blk_abort_flushes