- 07 11月, 2005 33 次提交
-
-
由 Roland Dreier 提交于
Add support for the AMCC PowerPC 440SPe SoC, including PCI Express in root port mode. Signed-off-by: NRoland Dreier <rolandd@cisco.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Roland Dreier 提交于
The PowerPC 440SP SoC has two Processor Local Bus (PLB) segments (a high-throughput segment and a low-latency segment). Fix our PLB register definitions to cope with this, and add code to dump the status of both segments when a machine check occurs. Signed-off-by: NRoland Dreier <rolandd@cisco.com> Cc: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Roland Dreier 提交于
The PowerPC 440SPe supports up to 16 GB of RAM, and therefore its IO registers are at 0x4_xxxx_xxxx instead of being at 0x1_xxxx_xxxx like most other PPC 440 chips. To allow for this, this patch moves the definition of the ERPN used for mapping UART0 from being hard-coded in the head_44x.S assembly code to being defined in ibm44x.h. Signed-off-by: NRoland Dreier <rolandd@cisco.com> Signed-off-by: NMatt Porter <mporter@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Lee Nicks 提交于
This patch adds watchdog, RTC support for Marvell EV64360BP board. Signed-off-by: NLee Nicks <allinux@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Stephen Hemminger 提交于
It is not valid to enable scatter/gather without hardware checksum support of some kind. (akpm: applies only to the old boomerang cards). Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Add capability for 3c59x driver to use memory-mapped PCI I/O resources. This may improve performance for those devices so equipped. This will be the default behaviour for IS_CYCLONE and IS_TORNADO devices. Additionally, it can be enabled/disabled individually for up to MAX_UNITS number of devices via the use_mmio module option or for all units via the global_use_mmio option. The use_mmio option overrides the global_use_mmio option for those devices specified. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Only increment rx_dropped in case of lack of resources (i.e. not for frames with errors). Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Add support for ETHTOOL_GPERMADDR to 3c59x. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Correct several (apparently cut & paste) grammatical typos in module parameter descriptions. They seem to have originated as copies of the description for "global_options". Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Beautify the array initilizations for the module parameters. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Add bounds checking to usage of hw_checksums module parameter array. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Tommy Christensen 提交于
In order to spare some I/O operations, be more intelligent about when to read from the PHY. Pointed out by Bogdan Costescu. Signed-off-by: NTommy S. Christensen <tommy.christensen@tpack.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Neil Horman 提交于
Clean up mdio_read routines in 3c59x.c to use the MII_* macros defined in include/linux/mii.h Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Convert 3c59x driver to use pci_iomap API. This makes it easier to enable the use of memory-mapped PCI I/O resources. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Manfred Spraul 提交于
Chen noticed that cache_reap uses REAPTIMEOUT_CPUC+smp_processor_id() as the timeout for rescheduling. The "+smp_processor_id()" part is wrong, the timeout should be identical for all cpus: start_cpu_timer already adds a cpu dependant offset to avoid any clustering. The attached patch removes smp_processor_id(). Signed-Off-By: NManfred Spraul <manfred@colorfullife.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Pekka J Enberg 提交于
This patch renames struct kmem_cache_s to kmem_cache so we can start using it instead of kmem_cache_t typedef. Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Andrew Morton 提交于
slab presently goes BUG if someone tries to register an already-registered cache. But this can happen if the user accidentally loads a module which is already statically linked into the kernel. Nuking the kernel is rather a harsh reaction. Change it into a warning, and just fail the kmem_cache_alloc() attempt. If the module is well-behaved, the modprobe will fail and all is well. Notes: - Swaps the ranking of cache_chain_sem and lock_cpu_hotplug(). Doesn't seem important. Acked-by: NManfred Spraul <manfred@colorfullife.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Andrew Morton 提交于
!unlikely(expr) hurts my brain. likely(!expr) is more straightforward. Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Benjamin Herrenschmidt 提交于
Oops, some last minute changes caused the 64K pages patch to break ppc32 build, this fixes it. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Benjamin Herrenschmidt 提交于
The zImage wrapper has a bug where it doesn't claim() the memory for the kernel properly, it forgets to take into account the offset between the ELF header and the kernel itself. This results on some machines, like G5s, into a kernel that crashes at boot when clearing the BSS. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Hugh Dickins 提交于
Suppress split ptlock on arches which may use one page for multiple page tables. Reconsider what better to do (particularly on ppc64) later on. Signed-off-by: NHugh Dickins <hugh@veritas.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Olof Johansson 提交于
Two CONFIG_SMP=n build fixes due to missing <asm/smp.h> includes. Signed-off-by: NOlof Johansson <olof@lixom.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
The current ia64 implementation of dma_get_cache_alignment does not work for modules because it relies on a symbol which is not exported. Direct access to a global is a little ugly anyway, so this patch re-implements dma_get_cache_alignment in a manner similar to what is currently used for x86_64. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Yuri Vasilevski 提交于
A typo fix for fix-build-on-nls-free-systems.patch that caused all systems to be detected as not having NLS. Signed-off-by: NYuri Vasilevski <yvasilev@duke.math.cinvestav.mx> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 David Gibson 提交于
This patch, however, should be applied on top of the 64k-page-size patch to fix some problems with hugepage (some pre-existing, another introduced by this patch). The patch fixes a bug in the SLB miss handler for hugepages on ppc64 introduced by the dynamic hugepage patch (commit id c594adad) due to a misunderstanding of the srd instruction's behaviour (mea culpa). The problem arises when a 64-bit process maps some hugepages in the low 4GB of the address space (unusual). In this case, as well as the 256M segment in question being marked for hugepages, other segments at 32G intervals will be incorrectly marked for hugepages. In the process, this patch tweaks the semantics of the hugepage bitmaps to be more sensible. Previously, an address below 4G was marked for hugepages if the appropriate segment bit in the "low areas" bitmask was set *or* if the low bit in the "high areas" bitmap was set (which would mark all addresses below 1TB for hugepage). With this patch, any given address is governed by a single bitmap. Addresses below 4GB are marked for hugepage if and only if their bit is set in the "low areas" bitmap (256M granularity). Addresses between 4GB and 1TB are marked for hugepage iff the low bit in the "high areas" bitmap is set. Higher addresses are marked for hugepage iff their bit in the "high areas" bitmap is set (1TB granularity). To avoid conflicts, this patch must be applied on top of BenH's pending patch for 64k base page size [0]. As such, this patch also addresses a hugepage problem introduced by that patch. That patch allows hugepages of 1MB in size on hardware which supports it, however, that won't work when using 4k pages (4 level pagetable), because in that case hugepage PTEs are stored at the PMD level, and each PMD entry maps 2MB. This patch simply disallows hugepages in that case (we can do something cleverer to re-enable them some other day). Built, booted, and a handful of hugepage related tests passed on POWER5 LPAR (both ARCH=powerpc and ARCH=ppc64). [0] http://gate.crashing.org/~benh/ppc64-64k-pages.diffSigned-off-by: NDavid Gibson <david@gibson.dropbear.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Linus Torvalds 提交于
-
由 Linus Torvalds 提交于
-
由 Linus Torvalds 提交于
-
由 Linus Torvalds 提交于
-
由 Benjamin Herrenschmidt 提交于
Adds a new CONFIG_PPC_64K_PAGES which, when enabled, changes the kernel base page size to 64K. The resulting kernel still boots on any hardware. On current machines with 4K pages support only, the kernel will maintain 16 "subpages" for each 64K page transparently. Note that while real 64K capable HW has been tested, the current patch will not enable it yet as such hardware is not released yet, and I'm still verifying with the firmware architects the proper to get the information from the newer hypervisors. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Russell King 提交于
glibc expects to count lines beginning with "processor" to determine the number of processors, not lines beginning with "Processor". So, give glibc the format it expects. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
We don't want to call dump_cpu_info() from cpu_init() after boot since it produces a lot of unnecessary noise - since cpu_init() gets called on resume and hotplug cpu insertion events. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 06 11月, 2005 7 次提交
-
-
由 Russell King 提交于
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Russell King 提交于
// disagrees with ld's script parsing ability. Don't use it. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Richard Purdie 提交于
Patch from Richard Purdie Update the PXA pm.c file to allow machines (such as the Sharp Zaurus) to override the standard pm functions but reuse/wrap them where needed. The init call is made slightly earlier to give machine code an init level to override them in removing any race. Signed-off-by: Richard Purdie Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Nicolas Pitre 提交于
Patch from Nicolas Pitre Since we know the value of cpsr on entry, we can replace the bic+orr with a single eor. Also remove a possible result delay (at least on XScale). Signed-off-by: NNicolas Pitre <nico@cam.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Lennert Buytenhek 提交于
Patch from Lennert Buytenhek Make the uengine loader use ixp2000_reg_wrb in the right places. Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Alessandro Zummo 提交于
Patch from Alessandro Zummo This patch fixes AHB/PCI endianness problems when the processor is in little-endian mode. The patch configures the CSR register closely following the directives in [1], paragraph 4.1, page 19. According to the considerations in [1], page 11, while the AHB bus supports both endian modes, on the IXP4XX it always uses big-endian. The PCI bus is connected to the South AHB. A wrong setting in the CSR register will thus cause a malfunctional PCI bus. A schematic diagram of the bus interconnections on the IXP4XX can be found in [1], page 18. The patch has been verified to work on the NSLU2 in both LE and BE modes. The author is Peter Korsgaard. [1] Intel® IXP4XX Product Line of Network Processors and IXC1100 Control Plane Processor: Understanding Big Endian and Little Endian Modes http://www.intel.com/design/network/applnots/25423701.pdfSigned-off-by: NAlessandro Zummo <a.zummo@towertech.it> Signed-off-by: NDeepak Saxena <dsaxena@plexity.net> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Dirk Opfer 提交于
Patch from Dirk Opfer This patch adds basic machine support for the Sharp SL-6000x (Tosa) PDAs. Signed-off-by: Dirk Opfer Signed-off-by: NRichard Purdie <rpurdie@rpsys.net> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-