- 06 10月, 2011 4 次提交
-
-
由 Borislav Petkov 提交于
Drop third nbcfg argument which is old remains and not required anymore. No functionality change. Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
-
由 Borislav Petkov 提交于
MCE decoding code is reporting the core which encountered the error unconditionally now so drop this piece. Besides, it reported the coreid in the local processor package which is not that valuable as a datapoint. Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
-
由 Borislav Petkov 提交于
The MCi_STATUS bank has a AddrV bit which, when set, denotes that the corresponding MCi_ADDR MSR contains a valid address belonging to the MCE currently being reported. Dump it since it is definitely relevant information. Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
-
由 Borislav Petkov 提交于
Currently, correctable ECCs go through mcelog and do not print the scary MCE banner. In that case, however, reporting the core where the CECC happened is important information so dump it along with the decoded string albeit at risk of having a minor redundancy. Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
-
- 05 10月, 2011 12 次提交
-
-
由 Linus Torvalds 提交于
-
git://github.com/davem330/net由 Linus Torvalds 提交于
* git://github.com/davem330/net: pch_gbe: Fixed the issue on which a network freezes pch_gbe: Fixed the issue on which PC was frozen when link was downed. make PACKET_STATISTICS getsockopt report consistently between ring and non-ring net: xen-netback: correctly restart Tx after a VM restore/migrate bonding: properly stop queuing work when requested can bcm: fix incomplete tx_setup fix RDSRDMA: Fix cleanup of rds_iw_mr_pool net: Documentation: Fix type of variables ibmveth: Fix oops on request_irq failure ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket cxgb4: Fix EEH on IBM P7IOC can bcm: fix tx_setup off-by-one errors MAINTAINERS: tehuti: Alexander Indenbaum's address bounces dp83640: reduce driver noise ptp: fix L2 event message recognition
-
git://github.com/tiwai/sound由 Linus Torvalds 提交于
* 'fix/asoc' of git://github.com/tiwai/sound: ASoC: omap_mcpdm_remove cannot be __devexit ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC ASoC: use a valid device for dev_err() in Zylonite
-
git://people.freedesktop.org/~airlied/linux由 Linus Torvalds 提交于
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/radeon/kms: fix channel_remap setup (v2) drm/radeon: Set cursor x/y to 0 when x/yorigin > 0. drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation. drm/radeon: Simplify cursor x/yorigin calculation. drm/radeon/kms: fix cursor image off-by-one error drm/radeon/kms: Fix logic error in DP HPD handler drm/radeon/kms: add retry limits for native DP aux defer drm/radeon/kms: fix regression in DP aux defer handling
-
git://git.secretlab.ca/git/linux-2.6由 Linus Torvalds 提交于
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6: spi-topcliff-pch: Fix overrun issue spi-topcliff-pch: Add recovery processing in case FIFO overrun error occurs spi-topcliff-pch: Fix CPU read complete condition issue spi-topcliff-pch: Fix SSN Control issue spi-topcliff-pch: add tx-memory clear after complete transmitting
-
由 Jon Mason 提交于
Add the ability to disable PCI-E MPS turning and using the BIOS configured MPS defaults. Due to the number of issues recently discovered on some x86 chipsets, make this the default behavior. Also, add the option for peer to peer DMA MPS configuration. Peer to peer DMA is outside the scope of this patch, but MPS configuration could prevent it from working by having the MPS on one root port different than the MPS on another. To work around this, simply make the system wide MPS the smallest possible value (128B). Signed-off-by: NJon Mason <mason@myri.com> Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alex Deucher 提交于
Most asics just use the hw default value which requires no explicit programming. For those that need a different value, the vbios will program it properly. As such, there's no need to program these registers explicitly in the driver. Changing MC_SHARED_CHREMAP requires a reload of all data in vram otherwise its contents will be scambled. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=40103 v2: drop now unused channel_remap functions. Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Tomoya MORINAGA 提交于
We found that adding load, Rx data sometimes drops.(with DMA transfer mode) The cause is that before starting Rx-DMA processing, Tx-DMA processing starts. This causes FIFO overrun occurs. This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor size like below. Current this patch Rx-descriptor 4Byte+12Byte*341 --> 12Byte*340-4Byte-12Byte Rx-threshold (Not modified) Tx-descriptor 4Byte+12Byte*341 --> 16Byte-12Byte*340 Rx-threshold 12Byte --> 2Byte Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
由 Tomoya MORINAGA 提交于
Add recovery processing in case FIFO overrun error occurs with DMA transfer mode. Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
由 Tomoya MORINAGA 提交于
We found Rx data sometimes drops.(with non-DMA transfer mode) The cause is read complete condition is not true. This patch fixes the issue. Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
由 Tomoya MORINAGA 提交于
During processing 1 command/data series, SSN should keep LOW. However, currently, SSN becomes HIGH. This patch fixes the issue. Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
由 Tomoya MORINAGA 提交于
Currently, in case of reading date from SPI flash, command is sent twice. The cause is that tx-memory clear processing is missing . This patch adds the tx-momory clear processing. Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com> Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
- 04 10月, 2011 17 次提交
-
-
由 Takashi Iwai 提交于
Commit 2a7fade7 ("hwmon: lis3: Power on corrections") caused a regression on HP laptops with 8bit chip. Writing CTRL2_BOOT_8B bit seems clearing the BIOS setup, and no proper interrupt for DriveGuard will be triggered any more. Since the init code there is basically only for embedded devices, put a pdata check so that the problematic initialization will be skipped for hp_accel stuff. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Cc: Eric Piel <eric.piel@tremplin-utc.net> Cc: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@google.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://github.com/groeck/linux由 Linus Torvalds 提交于
* 'hwmon-for-linus' of git://github.com/groeck/linux: hwmon: (coretemp) Avoid leaving around dangling pointer hwmon: (coretemp) Fixup platform device ID change
-
git://github.com/davem330/ide由 Linus Torvalds 提交于
* git://github.com/davem330/ide: ide-disk: Fix request requeuing
-
git://github.com/chrismason/linux由 Linus Torvalds 提交于
* 'btrfs-3.0' of git://github.com/chrismason/linux: Btrfs: force a page fault if we have a shorty copy on a page boundary
-
由 Borislav Petkov 提交于
Simon Kirby reported that on his RAID setup with idedisk underneath the box OOMs after a couple of days of runtime. Running with CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally allocates an ide_cmd struct. However, ide_requeue_and_plug() can be called more than once per request, either from the request issue or the IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn() repeatedly, allocating a struct ide_cmd everytime and "forgetting" the previous pointer. Make sure the code reuses the old allocated chunk. Reported-and-tested-by: NSimon Kirby <sim@hostway.ca> Cc: <stable@kernel.org> [ 39.x, 3.0.x ] Link: http://marc.info/?l=linux-kernel&m=131667641517919 Link: http://lkml.kernel.org/r/20110922072643.GA27232@hostway.caSigned-off-by: NBorislav Petkov <bp@alien8.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Toshiharu Okada 提交于
The pch_gbe driver has an issue which a network stops, when receiving traffic is high. In the case, The link down and up are necessary to return a network. This patch fixed this issue. Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Toshiharu Okada 提交于
When a link was downed during network use, there is an issue on which PC freezes. This patch fixed this issue. Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Willem de Bruijn 提交于
This is a minor change. Up until kernel 2.6.32, getsockopt(fd, SOL_PACKET, PACKET_STATISTICS, ...) would return total and dropped packets since its last invocation. The introduction of socket queue overflow reporting [1] changed drop rate calculation in the normal packet socket path, but not when using a packet ring. As a result, the getsockopt now returns different statistics depending on the reception method used. With a ring, it still returns the count since the last call, as counts are incremented in tpacket_rcv and reset in getsockopt. Without a ring, it returns 0 if no drops occurred since the last getsockopt and the total drops over the lifespan of the socket otherwise. The culprit is this line in packet_rcv, executed on a drop: drop_n_acct: po->stats.tp_drops = atomic_inc_return(&sk->sk_drops); As it shows, the new drop number it taken from the socket drop counter, which is not reset at getsockopt. I put together a small example that demonstrates the issue [2]. It runs for 10 seconds and overflows the queue/ring on every odd second. The reported drop rates are: ring: 16, 0, 16, 0, 16, ... non-ring: 0, 15, 0, 30, 0, 46, 0, 60, 0 , 74. Note how the even ring counts monotonically increase. Because the getsockopt adds tp_drops to tp_packets, total counts are similarly reported cumulatively. Long story short, reinstating the original code, as the below patch does, fixes the issue at the cost of additional per-packet cycles. Another solution that does not introduce per-packet overhead is be to keep the current data path, record the value of sk_drops at getsockopt() at call N in a new field in struct packetsock and subtract that when reporting at call N+1. I'll be happy to code that, instead, it's just more messy. [1] http://patchwork.ozlabs.org/patch/35665/ [2] http://kernel.googlecode.com/files/test-packetsock-getstatistics.cSigned-off-by: NWillem de Bruijn <willemb@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Vrabel 提交于
If a VM is saved and restored (or migrated) the netback driver will no longer process any Tx packets from the frontend. xenvif_up() does not schedule the processing of any pending Tx requests from the front end because the carrier is off. Without this initial kick the frontend just adds Tx requests to the ring without raising an event (until the ring is full). This was caused by 47103041 (net: xen-netback: convert to hw_features) which reordered the calls to xenvif_up() and netif_carrier_on() in xenvif_connect(). Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Acked-by: NIan Campbell <ian.campbell@citrix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
During a test where a pair of bonding interfaces using ARP monitoring were both brought up and torn down (with an rmmod) repeatedly, a panic in the timer code was noticed. I tracked this down and determined that any of the bonding functions that ran as workqueue handlers and requeued more work might not properly exit when the module was removed. There was a flag protected by the bond lock called kill_timers that is set when the interface goes down or the module is removed, but many of the functions that monitor link status now unlock the bond lock to take rtnl first. There is a chance that another CPU running the rmmod could get the lock and set kill_timers after the first check has passed. This patch does not allow any function to queue work that will make itself run unless kill_timers is not set. I also noticed while doing this work that bond_resend_igmp_join_requests did not have a check for kill_timers, so I added the needed call there as well. Signed-off-by: NAndy Gospodarek <andy@greyhouse.net> Reported-by: NLiang Zheng <lzheng@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michel Dänzer 提交于
Apart from the obvious cleanup, this should make the line cursor_end = x - xorigin + w; correct now. Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com> Reviewed-by: NAlex Deucher <alexander.deucher@amd.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Michel Dänzer 提交于
Fixes cursor disappearing prematurely when moving off a top/left edge which is not located at the desktop top/left edge. Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com> Cc: stable@kernel.org Reviewed-by: NAlex Deucher <alexander.deucher@amd.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Michel Dänzer 提交于
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com> Reviewed-by: NAlex Deucher <alexander.deucher@amd.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Nicholas Miell 提交于
The mouse cursor hotspot calculation when the cursor is partially off the top or left side of the screen was off by one. Fixes https://bugs.freedesktop.org/show_bug.cgi?id=41158Signed-off-by: NNicholas Miell <nmiell@gmail.com> Reviewed-by: NMichel Dänzer <michel@daenzer.net> Reviewed-by: NAlex Deucher <alexander.deucher@amd.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Only disable the pipe if the monitor is physically disconnected. The previous logic also disabled the pipe if the link was trained. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=41248Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
The previous code could potentially loop forever. Limit the number of DP aux defer retries to 4 for native aux transactions, same as i2c over aux transactions. Noticed by: Brad Campbell <lists2009@fnarfbargle.com> Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Cc: Brad Campbell <lists2009@fnarfbargle.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
An incorrect ordering in the error checking code lead to DP aux defer being skipped in the aux native write path. Move the bytes transferred check (ret == 0) below the defer check. Tracked down by: Brad Campbell <brad@fnarfbargle.com> Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=41121Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Cc: Brad Campbell <brad@fnarfbargle.com> Cc: stable@kernel.org Signed-off-by: NDave Airlie <airlied@redhat.com>
-
- 03 10月, 2011 5 次提交
-
-
git://git.infradead.org/users/sameo/mfd-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6: mfd: Fix generic irq chip ack function name for jz4740-adc
-
git://github.com/tiwai/sound由 Linus Torvalds 提交于
* 'for-linus' of git://github.com/tiwai/sound: ALSA: hda - Fix a regression of the position-buffer check
-
由 Arnd Bergmann 提交于
omap_mcpdm_remove is used from asoc_mcpdm_probe, which is an initcall, and must not be discarded when HOTPLUG is disabled. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
-
由 Axel Lin 提交于
Current code set update bits for WM8753_LDAC and WM8753_RDAC twice, but missed setting update bits for WM8753_LADC and WM8753_RADC. I think it is a copy-paste bug in commit 776065 "ASoC: codecs: wm8753: Fix register cache incoherency". Signed-off-by: NAxel Lin <axel.lin@gmail.com> Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
-
由 Arnd Bergmann 提交于
A recent conversion has introduced references to &pdev->dev, which does not actually exist in all the contexts it's used in. Replace this with card->dev where necessary, in order to let the driver build again. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
-
- 02 10月, 2011 1 次提交
-
-
git://tesla.tglx.de/git/linux-2.6-tip由 Linus Torvalds 提交于
* 'perf-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip: perf tools: Fix raw sample reading
-
- 01 10月, 2011 1 次提交
-
-
由 Linus Torvalds 提交于
Merge branches 'irq-urgent-for-linus', 'x86-urgent-for-linus' and 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip * 'irq-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip: irq: Fix check for already initialized irq_domain in irq_domain_add irq: Add declaration of irq_domain_simple_ops to irqdomain.h * 'x86-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip: x86/rtc: Don't recursively acquire rtc_lock * 'sched-urgent-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip: posix-cpu-timers: Cure SMP wobbles sched: Fix up wchan borkage sched/rt: Migrate equal priority tasks to available CPUs
-