This patch (as1653) fixes a bug in ehci-hcd.  Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to.  Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.

Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NAndy Leiserson <andy@leiserson.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PID and special handling for Telit LE920
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add VID and PID for Telit Gobi QDL device
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1652) fixes a long-standing bug in ehci-hcd.  The driver
relies on status polls to know when to stop port-resume signalling.
It uses the root-hub status timer to schedule these status polls.  But
when the driver for the root hub is resumed, the timer is rescheduled
to go off immediately -- before the port is ready.  When this happens
the timer does not get re-enabled, which prevents the port resume from
finishing until some other event occurs.

The symptom is that when a new device is plugged in, it doesn't get
recognized or enumerated until lsusb is run or something else happens.

The solution is to re-enable the root-hub status timer after every
status poll while a port resume is in progress.

This bug hasn't surfaced before now because we never used to try to
suspend the root hub in the middle of a port resume (except by
coincidence).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NNorbert Preining <preining@logic.at>
Tested-by: NMing Lei <ming.lei@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1651) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to uhci-hcd.  Now UHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1650) adds calls to the new
usb_hcd_{start,end}_port_resume() functions to ehci-hcd.  Now EHCI
root hubs won't be runtime suspended while they are sending a resume
signal to one of their ports.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1649) adds a mechanism for host controller drivers to
inform usbcore when they have begun or ended resume signalling on a
particular root-hub port.  The core will then make sure that the root
hub does not get runtime-suspended while the port resume is going on.

Since commit 596d789a (USB: set hub's
default autosuspend delay as 0), the system tries to suspend hubs
whenever they aren't in use.  While a root-hub port is being resumed,
the root hub does not appear to be in use.  Attempted runtime suspends
fail because of the ongoing port resume, but the PM core just keeps on
trying over and over again.  We want to prevent this wasteful effort.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1648) fixes a regression affecting nVidia EHCI
controllers.  Evidently they don't like to have more than one async QH
unlinked at a time.  I can't imagine how they manage to mess it up,
but at least one of them does.

The patch changes the async unlink logic in two ways:

	Each time an IAA cycle is started, only the first QH on the
	async unlink list is handled (rather than all of them).

	Async QHs do not all get unlinked as soon as they have been
	empty for long enough.  Instead, only the last one (i.e., the
	one that has been on the schedule the longest) is unlinked,
	and then only if no other unlinks are in progress at the time.

This means that when multiple QHs are empty, they won't be unlinked as
quickly as before.  That's okay; it won't affect correct operation of
the driver or add an excessive load.  Multiple unlinks tend to be
relatively rare in any case.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: NPiergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Cc: stable <stable@vger.kernel.org> # 3.6
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1647) attempts to work around a problem that seems to
affect some nVidia EHCI controllers.  They sometimes take a very long
time to turn off their async or periodic schedules.  I don't know if
this is a result of other problems, but in any case it seems wise not
to depend on schedule enables or disables taking effect in any
specific length of time.

The patch removes the existing 20-ms timeout for enabling and
disabling the schedules.  The driver will now continue to poll the
schedule state at 1-ms intervals until the controller finally decides
to obey the most recent command issued by the driver.  Just in case
this hides a problem, a debugging message will be logged if the
controller takes longer than 20 polls.

I don't know if this will actually fix anything, but it can't hurt.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NPiergiorgio Sartor <piergiorgio.sartor@nexgo.de>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-linus-2012-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:
	USB/xhci: Misc fixes for 3.8.

	Hi Greg,

	Here's six patches for xHCI and the USB core.  There's a couple of
	patches to fix xHCI 1.0 field formats, some memory leaks, dead ports,
	and USB 3.0 remote wakeup disabling.

	All of these are marked for stable.

	I know I owe you some re-works of failed stable patches from my last
	patchset round, but I don't think I'm going to get to them before I head
	off to Linux Conf Australia tomorrow.

	Sarah Sharp

Pull btrfs fixes from Chris Mason:
 "It turns out that we had two crc bugs when running fsx-linux in a
  loop.  Many thanks to Josef, Miao Xie, and Dave Sterba for nailing it
  all down.  Miao also has a new OOM fix in this v2 pull as well.

  Ilya fixed a regression Liu Bo found in the balance ioctls for pausing
  and resuming a running balance across drives.

  Josef's orphan truncate patch fixes an obscure corruption we'd see
  during xfstests.

  Arne's patches address problems with subvolume quotas.  If the user
  destroys quota groups incorrectly the FS will refuse to mount.

  The rest are smaller fixes and plugs for memory leaks."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (30 commits)
  Btrfs: fix repeated delalloc work allocation
  Btrfs: fix wrong max device number for single profile
  Btrfs: fix missed transaction->aborted check
  Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
  Btrfs: put csums on the right ordered extent
  Btrfs: use right range to find checksum for compressed extents
  Btrfs: fix panic when recovering tree log
  Btrfs: do not allow logged extents to be merged or removed
  Btrfs: fix a regression in balance usage filter
  Btrfs: prevent qgroup destroy when there are still relations
  Btrfs: ignore orphan qgroup relations
  Btrfs: reorder locks and sanity checks in btrfs_ioctl_defrag
  Btrfs: fix unlock order in btrfs_ioctl_rm_dev
  Btrfs: fix unlock order in btrfs_ioctl_resize
  Btrfs: fix "mutually exclusive op is running" error code
  Btrfs: bring back balance pause/resume logic
  btrfs: update timestamps on truncate()
  btrfs: fix btrfs_cont_expand() freeing IS_ERR em
  Btrfs: fix a bug when llseek for delalloc bytes behind prealloc extents
  Btrfs: fix off-by-one in lseek
  ...

Pull cifs fixes from Steve French:
 "Two small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fs/cifs/cifs_dfs_ref.c: fix potential memory leakage
  cifs: fix srcip_matches() for ipv6

Pull kvm fixlet from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Emulate dcbf

Pull ARM fixes from Russell King:
 "A number of fixes:

  Patrik found a problem with preempt counting in the VFP assembly
  functions which can cause the preempt count to be upset.

  Nicolas fixed a problem with the parsing of the DT when it straddles a
  1MB boundary.

  Subhash Jadavani reported a problem with sparsemem and our highmem
  support for cache maintanence for DMA areas, and TI found a bug in
  their strongly ordered memory mapping type.

  Also, three fixes by way of Will Deacon's tree from Dave Martin for
  instruction compatibility and Marc Zyngier to fix hypervisor boot mode
  issues."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
  ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
  ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
  ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
  ARM: virt: simplify __hyp_stub_install epilog
  ARM: virt: boot secondary CPUs through the right entry point
  ARM: virt: Avoid bx instruction for compatibility with <=ARMv4

Pull ARM SoC fixes from Olof Johansson:
 "Here's a long-pending fixes pull request for arm-soc (I didn't send
  one in the -rc4 cycle).

  The larger deltas are from:

   - A fixup of error paths in the mvsdio driver

   - Header file move for a driver that hadn't been properly converted
     to multiplatform on i.MX, which was causing build failures when
     included

   - Device tree updates for at91 dealing mostly with their new pinctrl
     setup merged in 3.8 and mistakes in those initial configs

  The rest are the normal mix of small fixes all over the place; sunxi,
  omap, imx, mvebu, etc, etc."

* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
  mfd: vexpress-sysreg: Don't skip initialization on probe
  ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
  ARM: vexpress: extend the MPIDR range used for pen release check
  ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
  ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
  ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
  ARM: at91/dts: add macb mii pinctrl config for kizbox
  ARM: at91: rm9200: remake the BGA as default version
  ARM: at91: fix gpios on i2c-gpio for RM9200 DT
  ARM: at91/at91sam9x5 DTS: add SCK USART pins
  ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
  ARM: at91/at91-pinctrl documentation: fix typo and add some details
  ARM: kirkwood: fix missing #interrupt-cells property
  mmc: mvsdio: use devm_ API to simplify/correct error paths.
  clk: mvebu/clk-cpu.c: fix memory leakage
  ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
  ARM: OMAP2+: DT node Timer iteration fix
  ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
  ARM: OMAP2+: fix build break for omapdrm
  ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
  ...

Pull ACPI and power management fixes from Rafael Wysocki:

 - Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.

 - cpufreq regression fixes for AMD processors from Borislav Petkov,
   Stefan Bader, and Matthew Garrett.

 - ACPI cpufreq fix from Thomas Schlichter.

 - cpufreq and devfreq fixes related to incorrect usage of operating
   performance points (OPP) framework and RCU from Nishanth Menon.

 - APEI workaround for incorrect BIOS information from Lans Zhang.

* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Add module aliases for acpi-cpufreq
  ACPI: Check MSR valid bit before using P-state frequencies
  PM / devfreq: exynos4_bus: honor RCU lock usage
  PM / devfreq: add locking documentation for recommended_opp
  cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
  cpufreq: OMAP: use RCU locks around usage of OPP
  ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
  ACPI / processor: Get power info before updating the C-states
  powernow-k8: Add a kconfig dependency on acpi-cpufreq
  ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
  intel_idle: Don't register CPU notifier if we are not running.

Pull regmap fixes from Mark Brown:
 "One more oversight in the debugfs code was reported and fixed, plus a
  documentation fix."

* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: fix small typo in regmap_bulk_write comment
  regmap: debugfs: Fix seeking from the cache

Pull slave-dmaengine fixes from Vinod Koul:
 "A few fixes on slave dmanengine.  There are trivial fixes in imx-dma,
  tegra-dma & ioat driver"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: tegra: implement flags parameters for cyclic transfer
  dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
  ioat: Fix DMA memory sync direction correct flag

Pill i2c fixes from Wolfram Sang:
 "Here are a few, typical driver fixes for the I2C subsystem"

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c-designware: add missing MODULE_LICENSE
  i2c: omap: fix draining irq handling
  i2c: omap: errata i462: fix incorrect ack for arbitration lost interrupt
  i2c: muxes: fix wrong use of sizeof(ptr)
  i2c: sirf: register i2c_client from dt child-nodes in probe entry
  i2c: mxs: Fix type of error code
  i2c: mxs: Fix misuse init_completion

Usb3.0 device defines function remote wakeup which is only for interface
recipient rather than device recipient. This is different with usb2.0 device's
remote wakeup feature which is defined for device recipient. According usb3.0
spec 9.4.5, the function remote wakeup can be modified by the SetFeature()
requests using the FUNCTION_SUSPEND feature selector. This patch is to use
correct way to disable usb3.0 device's function remote wakeup after suspend
error and resuming.

This should be backported to kernels as old as 3.4, that contain the
commit 623bef9e "USB/xhci: Enable remote
wakeup for USB3 devices."
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

When the xHCI driver is not available, actively switch the ports to EHCI
mode since some BIOSes leave them in xHCI mode where they would
otherwise appear dead.  This was discovered on a  Dell Optiplex 7010,
but it's possible other systems could be affected.

This should be backported to kernels as old as 3.0, that contain the
commit 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NDavid Moore <david.moore@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

This patch (as1640) fixes a memory leak in xhci-hcd.  The urb_priv
data structure isn't always deallocated in the handle_tx_event()
routine for non-control transfers.  The patch adds a kfree() call so
that all paths end up freeing the memory properly.

This patch should be backported to kernels as old as 2.6.36, that
contain the commit 8e51adcc "USB: xHCI:
Introduce urb_priv structure"
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-and-tested-by: NMartin Mokrejs <mmokrejs@fold.natur.cuni.cz>
CC: <stable@vger.kernel.org>

Fix incorrect bit test that originally showed up in
4ee823b8 "USB/xHCI: Support
device-initiated USB 3.0 resume."

Use '&' instead of '&&'.

This should be backported to kernels as old as 3.4.
Signed-off-by: NNickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

To calculate the TD size for a particular TRB in an isoc TD, we need
know the endpoint's max packet size.  Isochronous endpoints also encode
the number of additional service opportunities in their wMaxPacketSize
field.  The TD size calculation did not mask off those bits before using
the field.  This resulted in incorrect TD size information for
isochronous TRBs when an URB frame buffer crossed a 64KB boundary.

For example:
 - an isoc endpoint has 2 additional service opportunites and
   a max packet size of 1020 bytes
 - a frame transfer buffer contains 3060 bytes
 - one frame buffer crosses a 64KB boundary, and must be split into
   one 1276 byte TRB, and one 1784 byte TRB.

The TD size is is the number of packets that remain to be transferred
for a TD after processing all the max packet sized packets in the
current TRB and all previous TRBs.

For this TD, the number of packets to be transferred is (3060 / 1020),
or 3.  The first TRB contains 1276 bytes, which means it contains one
full packet, and a 256 byte remainder.  After processing all the max
packet-sized packets in the first TRB, the host will have 2 packets left
to transfer.

The old code would calculate the TD size for the first TRB as:

total packet count = DIV_ROUND_UP (TD length / endpoint wMaxPacketSize)
total packet count - (first TRB length / endpoint wMaxPacketSize)

The math should have been:

total packet count = DIV_ROUND_UP (3060 / 1020) = 3
3 - (1276 / 1020) = 2

Since the old code didn't mask off the additional service interval bits
from the wMaxPacketSize field, the math ended up as

total packet count = DIV_ROUND_UP (3060 / 5116) = 1
1 - (1276 / 5116) = 1

Fix this by masking off the number of additional service opportunities
in the wMaxPacketSize field.

This patch should be backported to stable kernels as old as 3.0, that
contain the commit 4da6e6f2 "xhci 1.0:
Update TD size field format."  It may not apply well to kernels older
than 3.2 because of commit 29cc8897
"USB: use usb_endpoint_maxp() instead of le16_to_cpu()".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

An isochronous TD is comprised of one isochronous TRB chained to zero or
more normal TRBs.  Only the isoc TRB has the TBC and TLBPC fields.  The
normal TRBs must set those fields to zeroes.  The code was setting the
TBC and TLBPC fields for both isoc and normal TRBs.  Fix this.

This should be backported to stable kernels as old as 3.0, that contain
the commit b61d378f " xhci 1.0: Set
transfer burst last packet count field."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

btrfs_start_delalloc_inodes() locks the delalloc_inodes list, fetches the
first inode, unlocks the list, triggers btrfs_alloc_delalloc_work/
btrfs_queue_worker for this inode, and then it locks the list, checks the
head of the list again. But because we don't delete the first inode that it
deals with before, it will fetch the same inode. As a result, this function
allocates a huge amount of btrfs_delalloc_work structures, and OOM happens.

Fix this problem by splice this delalloc list.
Reported-by: NAlex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

The max device number of single profile is 1, not 0 (0 means 'as many as
possible'). Fix it.

Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Reviewed-by: NLiu Bo <bo.li.liu@oracle.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

First, though the current transaction->aborted check can stop the commit early
and avoid unnecessary operations, it is too early, and some transaction handles
don't end, those handles may set transaction->aborted after the check.

Second, when we commit the transaction, we will wake up some worker threads to
flush the space cache and inode cache. Those threads also allocate some transaction
handles and may set transaction->aborted if some serious error happens.

So we need more check for ->aborted when committing the transaction. Fix it.
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

We may access and update transaction->aborted on the different CPUs without
lock, so we need ACCESS_ONCE() wrapper to prevent the compiler from creating
unsolicited accesses and make sure we can get the right value.
Signed-off-by: NMiao Xie <miaox@cn.fujitsu.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

I noticed a WARN_ON going off when adding csums because we were going over
the amount of csum bytes that should have been allowed for an ordered
extent.  This is a leftover from when we used to hold the csums privately
for direct io, but now we use the normal ordered sum stuff so we need to
make sure and check if we've moved on to another extent so that the csums
are added to the right extent.  Without this we could end up with csums for
bytenrs that don't have extents to cover them yet.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

For compressed extents, the range of checksum is covered by disk length,
and the disk length is different with ram length, so we need to use disk
length instead to get us the right checksum.
Signed-off-by: NLiu Bo <bo.li.liu@oracle.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

A user reported a BUG_ON(ret) that occured during tree log replay.  Ret was
-EAGAIN, so what I think happened is that we removed an extent that covered
a bitmap entry and an extent entry.  We remove the part from the bitmap and
return -EAGAIN and then search for the next piece we want to remove, which
happens to be an entire extent entry, so we just free the sucker and return.
The problem is ret is still set to -EAGAIN so we trip the BUG_ON().  The
user used btrfs-zero-log so I'm not 100% sure this is what happened so I've
added a WARN_ON() to catch the other possibility.  Thanks,
Reported-by: NJan Steffens <jan.steffens@gmail.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

We drop the extent map tree lock while we're logging extents, so somebody
could come in and merge another extent into this one and screw up our
logging, or they could even remove us from the list which would keep us from
logging the extent or freeing our ref on it, so we need to make sure to not
clear LOGGING until after the extent is logged, and then we can merge it to
adjacent extents.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>

From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms

* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
  mfd: vexpress-sysreg: Don't skip initialization on probe
  ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
  ARM: vexpress: extend the MPIDR range used for pen release check

From Nicolas Ferre:
Here are fixes for AT91 that are mainly related to device tree.
One RM9200 setup option is the only C code change.
Some documentation changes can clarify the pinctrl use.
Then, some defconfig modifications are allowing the affected platforms
to boot.

* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
  ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
  ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
  ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
  ARM: at91/dts: add macb mii pinctrl config for kizbox
  ARM: at91: rm9200: remake the BGA as default version
  ARM: at91: fix gpios on i2c-gpio for RM9200 DT
  ARM: at91/at91sam9x5 DTS: add SCK USART pins
  ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
  ARM: at91/at91-pinctrl documentation: fix typo and add some details

The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>

As the kernel is able to cope with multiple clusters,
uncomment the A7 cores in the Device Tree for V2P-CA15_A7
tile, making all 5 cores available to the user.
Signed-off-by: NPawel Moll <pawel.moll@arm.com>

In ARM multi-cluster systems the MPIDR affinity level 0 cannot be used as a
single cpu identifier, affinity levels 1 and 2 must be taken into account as
well.
This patch extends the MPIDR usage to affinity levels 1 and 2 in versatile
secondary cores start up code in order to compare the passed pen_release
value with the full-blown affinity mask.
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NLiviu Dudau <liviu.dudau@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NPawel Moll <pawel.moll@arm.com>