This function is supposed to be used at mode set time, so prevent
against future mistakes by adding a WARN().

Based on a patch by Paulo Zanoni, with the check extracted into a
little assert_hdmi_port_disabled helper added to make things self
documenting and move the assert stuff out of line.

[fixed up spelling goof-up while applying.]
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Change the ns_timeout parameter of the wait ioctl to a signed value.
Doing this allows the kernel to provide an infinite wait when a timeout
of less than 0 is provided. This mimics select/poll.

Initially the parameter was meant to match up with the GL spec 1:1, but
after being made aware of how much 2^64 - 1 nanoseconds actually is, I
do not think anyone will ever notice the loss of 1 bit.

The infinite timeout on waiting is similar to the existing i915
userspace interface with the exception that struct_mutex is dropped
while doing the wait in this ioctl.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's be a bit more paranoid here.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec Vol 3, Part 3, Section 3.8.1.1, bit 30:

"[DevIBX] Writing to this bit only takes effect when port is enabled.
Due to hardware issue it is required that this bit be cleared when port
is disabled. To clear this bit software must temporarily enable this
port on transcoder A."

Unfortunately the public Bspec misses totally out on the same language
for HDMIB. Internal Bspec also mentions that one of the bad
side-effects is that DPx can fail to light up on transcoder A if HDMIx
is disabled but using transcoder B.

I've found this while reviewing Bsepc. We already implement the same
workaround for the DP ports.

Also replace a magic 1 with PIPE_B I've found while looking through the
code.

v2: Implement suggestions from Chris Wilson:
- add pipe variable to cut down on code noise
- write the reg value twice to w/a hw issues (Bspec is unclear on
  which bit actually require the write twice stuff, but better be
  paranoid about it)
- untangle the if logic
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes for easier benchmarking and testing.  One can set a fixed
frequency by setting min and max to the same value.

v2: fix whitespace & comment (Eugeni)
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NEugeni Dodonov <eugeni@dodonov.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should only frob adjusted_mode. This is in preparation of
a massive patch by Laurent Pinchart to make the mode argument
const.

After the previous two prep patches the only thing left is to clean up
things a bit. I've opted to pass in an adjust_mode param to
dp_adjust_dithering because that way we can be sure to avoid
duplicating this logic between mode_valid and mode_fixup - which was
the cause behind a dp link bw calculation bug in the past.

Also mark the mode argument of pch_panel_fitting const.

v2: Split up the mode->clock => adjusted_mode->clock change,
as suggested by Chris Wilson.
Reported-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of changing mode->clock, which we should leave as-is.

After the previous patch we only touch that if it's a panel, and then
adjusted mode->clock equals adjusted_mode->clock. Outside of
intel_dp.c we only use ajusted_mode->clock in the mode_set functions.

Within intel_dp.c we only use it to calculate the dp dithering
and link bw parameters, so that's the only thing we need to fix
up.

As a temporary ugliness (until the cleanup in the next patch) we
pass the adjusted_mode into dp_dither for both parameters (because
that one still looks at mode->clock).

Note that we do overwrite adjusted_mode->clock with the selected dp
link clock, but that only happens after we've calculated everything we
need based on the dotclock of the adjusted output configuration.

Outside of intel_dp.c only intel_display.c uses adjusted_mode->clock,
and that stays the same after this patch (still equals the selected dp
link clock). intel_display.c also needs the actual dotclock (as
target_clock), but that has been fixed up in the previous patch.

v2: Adjust the debug message to also use adjusted_mode->clock.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... instead of abusing mode->clock by storing it in there - we
shouldn't touch that one at all. This patch is the first prep step to
constify the mode argument of the intel_dp_mode_fixup function.

The next patch will stop us from modifying mode->clock.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Both busy_ioctl and the new wait_ioct need to do the same dance (or at
least should). Some slight changes:
- busy_ioctl now unconditionally checks for olr. Before emitting a
  require flush would have prevent the olr check and hence required a
  second call to the busy ioctl to really emit the request.
- the timeout wait now also retires request. Not really required for
  abi-reasons, but makes a notch more sense imo.

I've tested this by pimping the i-g-t test some more and also checking
the polling behviour of the wait_rendering_timeout ioctl versus what
busy_ioctl returns.

v2: Too many people complained about unplug, new color is
flush_active.

v3: Kill the comment about the unplug moniker.

v4: s/un-active/inactive/
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of checking for !CPT, check for IBX to make it clearer that
this is a IBX-specific workaround. No functional change because we
smash the PPT PCH into the HAS_PCH_CPT check and atm DP isn't enabled
on the haswell LPT PCH yet.

See Bspec Vol 3, Part 3, Section 4.[3-5].1 about DP[BCD], bit 30 for
details of this workaround.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need the latest dma-buf code from Dave Airlie so that we can pimp
the backing storage handling code in drm/i915 with Chris Wilson's
unbound tracking and stolen mem backed gem object code.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Positively checking for the required feature/gen is simpler than build
a cascade of negative "we need to bail" checks. And the later won't
scale if we add more stuff that doesn't fit in nicely.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This fixes an (albeit really hard to hit) race resulting in an oops:
- The parity work get scheduled.
- We re-init the irq state and call INIT_WORK again.
- The workqueue code tries to run the work item and stumbles over a
  work item that should be on it's runlist.

Also initiliaze the work item unconditionally like all the others,
it's simpler.
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Notice by Fengguang Wu's automatic sparse checker.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is the same as the nouveau code pretty much.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Tested sharing to udl.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This allows udl to get a vmapping of an imported buffer for scanout.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is used to export a vmapping to the udl driver so that
i915 and udl can share the udl scanout.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds a stub until we have pieces in place to test
a correct one.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds a stub until we have some users in place to test
this with.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This just adds a stub for now, until we have some users in
place to test this functionality properly.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Dumb binary interfaces which allow root-only updates of the cache
remapping registers. As mentioned in a previous patch, software using
this interface needs to know about HW limits, and other programming
considerations as the kernel interface does no checking for these things
on the root-only interface.

v1: Drop extra posting reads (Chris)
Return negative values in the sysfs interfaces on errors (Chris)

v2: Return -EINVAL for offset % 4 (Jesse)
Move schizo userspace check out (Jesse)
Cleaner sysfs item initializers (Daniel)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If any l3 rows have been previously remapped, we must remap them after
GPU reset/resume too.

v2: Just return (no warn) on remapping init if not IVB (Jesse)
Move the check of schizo userspace to i915_gem_l3_remap (Jesse)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The previous patch put all the code, and handlers in place. It should
now be safe to enable the parity error interrupt. The parity error must
be unmasked in both the GTIMR, and the CS IMR. Unfortunately, the docs
aren't clear about this; nevertheless it's the truth.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On IVB hardware we are given an interrupt whenever a L3 parity error
occurs in the L3 cache. The L3 cache is used by internal GPU clients
only.  This is a very rare occurrence (in fact to test this I need to
use specially instrumented silicon).

When a row in the L3 cache detects a parity error the HW generates an
interrupt. The interrupt is masked in GTIMR until we get a chance to
read some registers and alert userspace via a uevent. With this
information userspace can use a sysfs interface (follow-up patch) to
remap those rows.

Way above my level of understanding, but if a given row fails, it is
statistically more likely to fail again than a row which has not failed.
Therefore it is desirable for an operating system to maintain a lifelong
list of failing rows and always remap any bad rows on driver load.
Hardware limits the number of rows that are remappable per bank/subbank,
and should more than that many rows detect parity errors, software
should maintain a list of the most frequent errors, and remap those
rows.

V2: Drop WARN_ON(IS_GEN6) (Jesse)
DRM_DEBUG row/bank/subbank on errror (Jesse)
Comment updates (Jesse)
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A 30 ms delay is simply way too big to waste cpu cycles on.
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Jesse extracted this nice helper in his i9xx_crtc_mode_set refactor,
but we have the identical code in ironlake_ccrtc_mode_set. And that
function is huge, so extracting some code full of magic numbers is
always nice.

Noticed while trying to get a handle on our dp clock code.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Already discovered in

commit 5a117db7
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date:   Thu Jan 5 09:34:29 2012 -0200

    drm/i915: there is no pipe CxSR on ironlake

but we've failed to rip out the code from the ironlake specific code.
Reviewed-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On IVB and older, we basically have two registers: the control and the
data register. We write a few consecutitve times to the control
register, and we need these writes to arrive exactly in the specified
order.

Also, when we're changing the data register, we need to guarantee that
anything written to the control register already arrived (since
changing the control register can change where the data register
points to). Also, we need to make sure all the writes to the data
register happen exactly in the specified order, and we also *can't*
read the data register during this process, since reading and/or
writing it will change the place it points to.

So invoke the "better safe than sorry" rule and just be careful and
put barriers everywhere :)

On HSW we still have a control register that we write many times, but
we have many data registers.
Demanded-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HSW support is now just like all the other generations: we send AVI
and SPD InfoFrames. There are other DIPs for HSW, but there are other
DIPs for the previous generations too. For each gen, we can see which
DIPs are missing by looking at the 'set_infoframes' function: we
explicitly disable the DIPs we're not using.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The register that controls the HDMI port can be used to control the
sDVO port. Some bits are defined only for sDVO, and SDVO_BORDER_ENABLE
is one of those: HDMI ports that can't be used in sDVO mode don't even
have this bit defined in their specifications.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At this time, the HDMI port is enabled, and the DIP control register
specification says we need to disable the port *before* disabling the
DIPs. Also, while doing this we risk telling the HW to send the AVI
DIPs once (not every VSync), which really seems to confuse the HW and
trigger bugs where the DIPs are not sent.

This code was here just to set the DIP register to a 'known state'
before using it, but since now the set_infoframes functions already
set the control registers to a known state, this code can go away.

Also, the previous code disables *all* the DIP registers for *each*
HDMI port, so we end disabling each DIP register more than once.

This patch solves a problem I can reproduce on my IVB machine. When I
boot it with just a single HDMI monitor, the AVI InfoFrames are not
sent. With this patch, the InfoFrames are sent. Previously, I wrote a
patch to 'touch the DIP registers after we enable the HDMI port' to
solve this same problem, but that patch doesn't seem to be needed
anymore after this patch.

All this patch does is revert a chunk of the following commit:

    commit 64a8fc01
    Author: Jesse Barnes <jbarnes@virtuousgeek.org>
    Date:   Thu Sep 22 11:16:00 2011 +0530

        drm/i915: fix ILK+ infoframe support

So bugs that can be bisected to that commit may be fixed now.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43256Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The register specification says we need to do this.

V2: Only write the register if the port is enabled.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

From this point on, the 'set_infoframe' functions always set the DIP
registers to a known state, so anything done will always be undone at
the modeset.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is called when the pipe is disabled, so it always gets
the 50ms timeout.

This function is called once for each InfoFrame, so we actually get a
100ms timeout. Will be more if we add more InfoFrames.

Also, the spec says we need to "wait for a VSync to ensure completion
of any pending DIP transmissions", not for a VBlank. OTOH, the
register documentation suggests that the DIPs are sent *during* the
VSync, so shouldn't we be waiting until *after* the VSync to ensure
all DIPs are sent?

So this wait_for_vblank seems, besides useless, totally wrong.

If we ever want to change some specific InfoFrame on-the-fly (outside
of the modeset code), the code that changes the InfoFrame will have to
do the waiting itself, and properly.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

So the write_infoframe function can assume the DIP is on.

V2: Be more defensive and add WARN().
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Not once for each InfoFrame. Now we have a function that allows us to
do this.

[danvet: Paulo clarified on irc that a later bugfix patch needs this
cleanup.]
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This solves problems that happen when you alternate between HDMI and
DVI on the same port. I can reproduce these problems using DP->HDMI
and DP->DVI adapters on a DP port.

When you first plug HDMI and then plug DVI, you need to stop sending
DIPs, even if the port is in DVI mode (see the HDMI register spec). If
you don't stop sending DIPs, you'll see a pink vertical line on the
left side of the screen, some modes will give you a black screen, some
modes won't work correctly.

When you first plug DVI and then plug HDMI, you need to properly
enable the DIPs, otherwise the HW won't send them. After spending a
lot of time investigating this, I concluded that if the DIPs are
disabled, we should not write to the DIP register again because when
we do this, we also set the AVI InfoFrame frequency to "once", and
this seems to really confuse our hardware. Since this problem was not
exactly easy to debug, I'm adopting the defensive behavior and not
just avoing the "disable twice" sequence, but also explicitly
selecting the AVI InfoFrame and setting its frequency to a correct
one.

Also, move the "is_dvi" check from intel_set_infoframe to the
set_infoframes functions since now they're going to be the first ones
to deal with the DIP registers.

This patch adds the code to fix the problem, but it depends on the
removal of some code that can't be removed right now and will come
later in the patch series. The patch that we need is:
  - drm/i915: don't write 0 to DIP control at HDMI init

[danvet: Paulo clarified that this additional patch is only required
to make the fix complete, this patch here alone doesn't introduce a
regression but only partially solves the problem of randomly clearing
the dip registers.]

V2: Be even more defensive by selecting AVI and setting its frequency
outside the "is_dvi" check.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need a function that is able to fully 'set' the state of the DIP
registers to a known state.

Currently, we have the write_infoframe function that is called twice:
once for AVI and once for SPD. The problem is that write_infoframe
tries to keep the state of the DIP register as it is, changing only
the minimum necessary bits. The second problem is that
write_infoframe does twice (once for each time it is called) some
work that should be done only once (like waiting for vblank and
setting the port). If we add even more DIPs, it will do even more
repeated work.

This patch only adds the infrastructure keeping the code behavior the
same as before.

v2: add static keywords
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>