Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.
Reported-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
   zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode
Signed-off-by: NIdo Yariv <ido@wizery.com>
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Definitions to support wl128x:
  - New FW file name
  - Chip ID
  - New PLL Configuration Algorithm macros that will be used at wl128x
    boot stage
  - Rename NVS macro name: wl127x and wl128x are using the same NVS
    file name. However, the ini parameters between them are
    different. The driver will validate the correct NVS size in
    wl1271_boot_upload_nvs().

[Cleaned up some of the definitions. -- Luca]
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

On newer hardware revisions, there is no need to write the host's
counter at the end of a RX transaction. The same applies to writing the
number of packets at the end of a TX transaction.

It is generally a good idea to avoid unnecessary SDIO/SPI transfers.
Throughput and CPU usage are improved when avoiding these.

Send the host's RX counter and the TX packet count only if needed, based
on the hardware revision.

[Changed WL12XX_QUIRK_END_OF_TRANSACTION to use BIT(0) -- Luca]
Signed-off-by: NIdo Yariv <ido@wizery.com>
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Reviewed-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

For the SDIO testing module we need to load the firmware but not
boot it. wl1271_load_firmware() is meant to do just the firmware loading part.

We also export some functions so they are usable in the testing module.
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>

The wl1271 device is using a reference clock that may change
between board to board.

Make the ref_clock parameter configurable by board settings
instead of having a hard coded value in the sources.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reads the HW PG version (along with a ROM-version, embedded in the
same value) from the wl1271 hardware and publishes the value in a sysfs -file.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch configures the wl1271 chipset clock-request line to be
driver in open-drain mode instead of push-pull.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Updated RefClk configuration based on reference sources. Apparently this
change will improve RF performance.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add top register access function.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver supports the wl1271 chipset from Texas Instruments based on the
WiLink(tm) 6.0 mobile platform.  Support for wl1273 should be relatively easy
to add.  This chipset is designed for embedded devices, with good powersaving
capabilities.  The wl1271 chipset is the successor of wl1251 and supports the
802.11b/g/n standards, but currently this driver supports only b/g.

More information about this chipset can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12762&contentId=29993Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>