This is necessary in order to support > 1 VF/PF in a VM for software
that uses the node guid as a discriminator, such as librdmacm.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Remove the error returns for IB ports from mlx4_ib_add,
mlx4_INIT_PORT_wrapper, and mlx4_CLOSE_PORT_wrapper.

Currently, SRIOV is supported only for devices for which the
link layer is IB on all ports; RoCE support will be added later.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

1. Slaves may not set the IS_SM capability for the port.
2. DEV_MGMT may not be set in multifunction mode.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

For an IB port, a slave should not show port active until that slave
has a valid alias-guid (provided by the subnet manager).  Therefore
the port-up event should be passed to a slave only after both the port
is up, and the slave's alias-guid has been set.

Also, provide the infrastructure for propagating port-management
events (client-reregister, etc) to slaves.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

This requires:

1. Replacing the paravirtualized P_Key index (inserted by the guest)
   with the real P_Key index.

2. For UD QPs, placing the guest's true source GID index in the
   address path structure mgid field, and setting the ud_force_mgid
   bit so that the mgid is taken from the QP context and not from the
   WQE when posting sends.

3. For UC and RC QPs, placing the guest's true source GID index in the
   address path structure mgid field.

4. For tunnel and proxy QPs, setting the Q_Key value reserved for that
   proxy/tunnel pair.

Since not all the above adjustments occur in all the QP transitions,
the QP transitions require separate wrapper functions.

Secondly, initialize the P_Key virtualization table to its default
values: Master virtualized table is 1-1 with the real P_Key table,
guest virtualized table has P_Key index 0 mapped to the real P_Key
index 0, and all the other P_Key indices mapped to the reserved
(invalid) P_Key at index 127.

Finally, add logic in smp_snoop for maintaining the phys_P_Key_cache.
and generating events on the master only if a P_Key actually changed.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Allocate SR-IOV paravirtualization resources and MAD demuxing contexts
on the master.

This has two parts.  The first part is to initialize the structures to
contain the contexts.  This is done at master startup time in
mlx4_ib_init_sriov().

The second part is to actually create the tunneling resources required
on the master to support a slave.  This is performed the master
detects that a slave has started up (MLX4_DEV_EVENT_SLAVE_INIT event
generated when a slave initializes its comm channel).

For the master, there is no such startup event, so it creates its own
tunneling resources when it starts up.  In addition, the master also
creates the real special QPs.  The ib_core layer on the master causes
creation of proxy special QPs, since the master is also
paravirtualized at the ib_core layer.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

In addition, pass the proxy and tunnel QP numbers to slaves so the
driver can perform special QP paravirtualization.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

1. Introduce the basic SR-IOV parvirtualization context objects for
   multiplexing and demultiplexing MADs.
2. Introduce support for the new proxy and tunnel QP types.

This patch introduces the objects required by the master for managing
QP paravirtualization for guests.

struct mlx4_ib_sriov is created by the master only.
It is a container for the following:

1. All the info required by the PPF to multiplex and de-multiplex MADs
   (including those from the PF). (struct mlx4_ib_demux_ctx demux)
2. All the info required to manage alias GUIDs (i.e., the GUID at
   index 0 that each guest perceives.  In fact, this is not the GUID
   which is actually at index 0, but is, in fact, the GUID which is at
   index[<VF number>] in the physical table.
3. structures which are used to manage CM paravirtualization
4. structures for managing the real special QPs when running in SR-IOV
   mode.  The real SQPs are controlled by the PPF in this case.  All
   SQPs created and controlled by the ib core layer are proxy SQP.

struct mlx4_ib_demux_ctx contains the information per port needed
to manage paravirtualization:

1. All multicast paravirt info
2. All tunnel-qp paravirt info for the port.
3. GUID-table and GUID-prefix for the port
4. work queues.

struct mlx4_ib_demux_pv_ctx contains all the info for managing the
paravirtualized QPs for one slave/port.

struct mlx4_ib_demux_pv_qp contains the info need to run an individual
QP (either tunnel qp or real SQP).

Note:  We made use of the 2 most significant bits in enum
mlx4_ib_qp_flags (based on enum ib_qp_create_flags in ib_verbs.h).
We need these bits in the low-level driver for internal purposes.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Since VFs may be mapped to VMs which aren't trusted entities,  flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable callers of mlx4_assign_eq to supply a pointer to cpu_rmap.
If supplied, the assigned IRQ is tracked using rmap infrastructure.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.

In addition, in SR-IOV mode, do the following:

1. Reduce reported P_Key table size by 1.
   This is done to reserve the highest P_Key index for internal use,
   for declaring an invalid P_Key in P_Key paravirtualization.
   We require a P_Key index which always contain an invalid P_Key
   value for this purpose (i.e., one which cannot be modified by
   the subnet manager).  The way to do this is to reduce the
   P_Key table size reported to the subnet manager by 1, so that
   it will not attempt to access the P_Key at index #127.

2. Paravirtualize the GID table size to 1. Thus, each guest sees
   only a single GID (at its paravirtualized index 0).

In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The SR-IOV special QP tunneling mechanism uses proxy special QPs
(instead of the real special QPs) for MADs on guests.  These proxy QPs
send their packets to a "tunnel" QP owned by the master.  The master
then forwards the MAD (after any required paravirtualization) to the
real special QP, which sends out the MAD.

For security reasons (i.e., to prevent guests from sending MADs to
tunnel QPs belonging to other guests), each proxy-tunnel QP pair is
assigned a unique, reserved, Q_Key.  These Q_Keys are available only
for proxy and tunnel QPs -- if the guest tries to use these Q_Keys
with other QPs, it will fail.

This patch introduces a mechanism for reserving a block of 64K Q_Keys
for proxy/tunneling use.

The patch introduces also two new fields into mlx4_dev: base_sqpn and
base_tunnel_sqpn.

In SR-IOV mode, the QP numbers for the "real," proxy, and tunnel sqps
are added to the reserved QPN area (so that they will not change).
There are 8 special QPs per port in the HCA, and each of them is
assigned both a proxy and a tunnel QP, for each VF and for the PF as
well in SR-IOV mode.

The QPNs for these QPs are arranged as follows:
 1. The real SQP numbers (8)
 2. The proxy SQPs (8 * (max number of VFs + max number of PFs)
 3. The tunnel SQPs (8 * (max number of VFs + max number of PFs)

To support these QPs, two new fields are added to struct mlx4_dev:

  base_sqp:  this is the QP number of the first of the real SQPs
  base_tunnel_sqp: this is the qp number of the first qp in the tunnel
                   sqp region. (On guests, this is the first tunnel
                   sqp of the 8 which are assigned to that guest).

In addition, in SR-IOV mode, sqp_start is the number of the first
proxy SQP in the proxy SQP region.  (In guests, this is the first
proxy SQP of the 8 which are assigned to that guest)

Note that in non-SR-IOV mode, there are no proxies and no tunnels.
In this case, sqp_start is set to sqp_base -- which minimizes code
changes.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

With IB SR-IOV, each slave has its own separate copy of the port
capabilities flags.  For example, the master can run a subnet manager
(which causes the IsSM bit to be set in the master's port
capabilities) without affecting the port capabilities seen by the
slaves (the IsSM bit will be seen as cleared in the slaves).

Also add a static inline mlx4_master_func_num() to enhance readability
of the code.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The port management change event can replace smp_snoop.  If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command).  In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.

If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).

In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events.  The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).

Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.

We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Currently, VFs have 0 in their dev->caps.function field.  This is a
valid pci id (usually of the PF).  Instead, pass an invalid PCI id to
the VF via QUERY_FW, so that if the value gets accessed in the VF
driver, we'll catch the problem.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.

This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.

A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.

B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,

The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In SRIOV mode, the number of EQs used when computing the total ICM size
was incorrect.

To fix this, we do the following:
1. We add a new structure to mlx4_dev, mlx4_phys_caps, to contain physical HCA
   capabilities.  The PPF uses the phys capabilities when it computes things
   like ICM size.

   The dev_caps structure will then contain the paravirtualized values, making
   bookkeeping much easier in SRIOV mode. We add a structure rather than a
   single parameter because there will be other fields in the phys_caps.

   The first field we add to the mlx4_phys_caps structure is num_phys_eqs.

2. In INIT_HCA, when running in SRIOV mode, the "log_num_eqs" parameter
   passed to the FW is the number of EQs per VF/PF; each function (PF or VF)
   has this number of EQs available.

   However, the total number of EQs which must be allowed for in the ICM is
   (1 << log_num_eqs) * (#VFs + #PFs).  Rather than compute this quantity,
   we allocate ICM space for 1024 EQs (which is the device maximum
   number of EQs, and which is the value we place in the mlx4_phys_caps structure).

   For INIT_HCA, however, we use the per-function number of EQs as described
   above.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a 64-bit flags2 features member to struct mlx4_dev to
export further features of the hardware.  The original flags field
tracks features whose support bits are advertised by the firmware in
offsets 0x40 and 0x44 of the query device capabilities command.
flags2 will track features whose support bits are scattered at various
offsets.

RSS support is the first feature to be exported through flags2.  RSS
capabilities are located at offset 0x2e.  The size of the RSS
indirection table is also given in this offset.
Signed-off-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB).  Allow for dynamic mtu
configuration through a new, per-port sysfs entry.

Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.

For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode.  To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Print an error message when a thermal error async event is reported by the HW.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDotan Barak <dotanb@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

While doing the work for commit a6f7feae ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b78 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).

This patch reverts commit 97285b78 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The SET_PORT functions are implemented in port.c, which is part
of mlx4_core, these functions are exported. The functions are in use by
the mlx4_en module (were originally part of mlx4_en).
Their declaration remained in mlx4_en module, moving the declaration to the right location.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt.  The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.

Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

In native mode display all available staticstics.
In SRIOV mode on VF display only SW counters statistics,
in SRIOV mode on hypervisor display SW counters and errors (got from FW)
statistics.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New FW can give clues to driver regarding default port type
and whether or not we should default to link sensing on the port.

2 bits are added to QUERY_PORT command:
1. suggested_type: This bit gives a hint whether the default port type should be
   IB or Ethernet.
   The driver will use this hint in case the user didn't specify explicitly the link layer
   type he wants to set.
2. default_sense: If this bit is set, we would sense the port type on start-up
   and default the port to link sensing
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ConnectX3 devices, we allow link sensing only if FW explicitly
reported it supports the feature.
For older versions (ConnectX1 and 2), if the card supports both link layer types
(Ethenet and Infiniband), link sensing is supported.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Added module parameters sr_iov and probe_vf for controlling enablement of
   SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
   SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
   ports configured as desired.
   In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
   for the case where the FW supports both port types (ETH and IB), the
   port_type_array parameter is used.
   By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
   to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
   mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
   modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
   VFs obtain their startup information from the PF (master) device via the
   comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
   aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership:  Currently, only one PF is supported by the driver.
   If the HCA is burned with FW which enables more than one PF, only one
   of the PFs is allowed to run.  The first one up grabs a FW ownership
   semaphone -- all other PFs will find that semaphore taken, and the
   driver will not allow them to run.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NLiran Liss <liranl@mellanox.co.il>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the previous implementation mtts are managed by:
1. order     - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order     - log(mtts) rather than segments
2. offset    - mtt index in mtt table

Note: The actual mtt allocation is made in segments but it is
      transparent to callers.

Rational: The mtt resource holders are not interested on how the allocation
          of mtt is done, but rather on how they will use it.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware

Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.

Change the allocator to return only 17 bits for the PD.  The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).

Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
  (i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
  PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
  by other mlx4_core source files).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 2 capability bits for WOL, one for each port.
WOL handlers were looking only on the second bit, regardless of the port.
Signed-off-by: NOren Duer <oren@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An Extended Port Info packet is sent to each hw port during HCA init.
If it returns without error, we assume the port supports extended port
capabilities.
Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Canceling FCS removal where FW allows for better alignment
of incoming data.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the user to create XRC SRQs.  This patch is based on a patch
from Jack Morgenstrein <jackm@dev.mellanox.co.il>.
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>